| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | ( )
|
- | - |
| 2 | INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY | - | - | - | - |
| 3 | BENCH TYPE REAR SEATBACK ASSEMBLY | - | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | REAR DOOR SCUFF PLATE INSIDE LH | 67918F | - | - | - |
| 5 | REAR DOOR SCUFF PLATE INSIDE RH | 67917F | - | - | - |
| 6 | REAR DOOR OPENING TRIM WEATHERSTRIP LH | 62332A | - | - | - |
| 7 | REAR DOOR OPENING TRIM WEATHERSTRIP RH | 62331A | - | - | - |
| 8 | REAR SEAT SIDE GARNISH LH | 62552F | - | - | - |
| 9 | REAR SEAT SIDE GARNISH RH | 62551F | - | - | - |
| 10 | INNER ROOF SIDE GARNISH COVER LH | 62488A | - | - | - |
| 11 | INNER ROOF SIDE GARNISH COVER RH | 62487A | - | - | - |
| 12 | INNER ROOF SIDE GARNISH ASSEMBLY LH | 62480A | - | - | - |
| 13 | INNER ROOF SIDE GARNISH ASSEMBLY RH | 62470A | - | - | - |
| 14 | ROOF SIDE RAIL GARNISH ASSEMBLY LH | 62440 | - | - | - |
| 15 | ROOF SIDE RAIL GARNISH ASSEMBLY RH | 62430 | - | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 16 | FRONT DOOR OPENING TRIM WEATHERSTRIP LH | 62312B | - | - | - |
| 17 | FRONT DOOR OPENING TRIM WEATHERSTRIP RH | 62311B | - | - | - |
| 18 | LOWER CENTER PILLAR GARNISH LH | 62414A | - | - | - |
| 19 | LOWER CENTER PILLAR GARNISH RH | 62413A | - | - | - |
| 20 | CENTER PILLAR GARNISH ASSEMBLY LH | 62420A | - | - | - |
| 21 | CENTER PILLAR GARNISH ASSEMBLY RH | 62410A | - | - | - |
| ● | Non-reusable part | - | - |
| *A | w/ ETC System | - | - |
| *1 | ASSIST GRIP COVER | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 37 | ROOF HEADLINING ASSEMBLY | 63310 | ( )
|
- | - |
| *A | for Normal Roof | *B | for Panoramic Moon Roof |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor standard position is recognized. | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
2.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
3.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY
67918F
4.REMOVE REAR DOOR SCUFF PLATE INSIDE LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
67917F
5.REMOVE REAR DOOR SCUFF PLATE INSIDE RH
Use the same procedure described for the LH side.
62332A
6.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
62331A
7.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62552F
8.REMOVE REAR SEAT SIDE GARNISH LH
|
Remove in this Direction | - | - |
62551F
9.REMOVE REAR SEAT SIDE GARNISH RH
Use the same procedure described for the LH side.
62488A
10.REMOVE INNER ROOF SIDE GARNISH COVER LH
|
Remove in this Direction | - | - |
62487A
11.REMOVE INNER ROOF SIDE GARNISH COVER RH
Use the same procedure described for the LH side.
62480A
12.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
|
Remove in this Direction | - | - |
When reusing a inner roof side garnish assembly LH:
| *a | Clip A | *b | Clip B |
62470A
13.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
62440
14.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
|
Remove in this Direction | - | - |
When reusing a roof side rail garnish assembly LH:
| *a | Clip A | *b | Clip B |
62430
15.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
62312B
16.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
17.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62414A
18.REMOVE LOWER CENTER PILLAR GARNISH LH
|
Place Hand Here |
|
Remove in this Direction |
62413A
19.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure described for the LH side.
62420A
20.REMOVE CENTER PILLAR GARNISH ASSEMBLY LH
|
Place Hand Here |
|
Remove in this Direction |
When reusing a center pillar garnish assembly LH:
62410A
21.REMOVE CENTER PILLAR GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
74610A
22.REMOVE ASSIST GRIP SUB-ASSEMBLY
| *a | Cutout | *b | 30 to 45° |
|
Remove in this Direction | - | - |
Insert SST into the cutout of the assist grip cover as shown in the illustration.
To prevent the assist grip sub-assembly from being damaged, make sure to insert SST straight into the cutout.
Pull SST as shown in the illustration to detach the claw.
To prevent the assist grip sub-assembly from being damaged, make sure to only pull SST as shown in the illustration.
Use the same procedure for the claw on the other side of the assist grip cover.
|
Remove in this Direction | - | - |
Detach the clip and remove the assist grip sub-assembly as shown in the illustration.
Remove the 4 clips.
74630E
23.REMOVE REAR ASSIST GRIP ASSEMBLY LH
Use the same procedure for the assist grip sub-assembly.
74620C
24.REMOVE REAR ASSIST GRIP ASSEMBLY RH
Use the same procedure for the assist grip sub-assembly.
75631L
25.REMOVE FRONT ROOF TOP GARNISH
|
Remove in this Direction | - | - |
89943
31.REMOVE RAIN SENSOR COVER
74325
32.REMOVE VISOR BRACKET COVER
Use the same procedure for the opposite side.
74320
33.REMOVE VISOR ASSEMBLY LH
74310
34.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74348
35.REMOVE VISOR HOLDER
|
Turn in this Direction |
|
Remove in this Direction |
36.REMOVE TOLL COLLECTION COVER (w/ ETC System)
63310
37.REMOVE ROOF HEADLINING ASSEMBLY
for Front Pillar LH Side:
1. Remove the protective cover installed to the front pillar LH.
2. Disconnect the 2 connectors.
3. Detach the clamp.
4. Install the protective cover to the front pillar LH.
for Windshield Glass Side:
1. Disconnect each connector.
for Rear Pillar RH Side:
1. Disconnect the connector.
2. Detach the clamp.
w/ ETC System:
Disconnect the connector.
for Normal Roof:
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the visor holder base as shown in the illustration.
Detach the clip and remove the roof headlining assembly.
Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.
Check that the corners of the roof headlining assembly are free of bending, twisting and other deformation and that none of the mounted parts are falling off.
Do not damage the roof headlining assembly and body interior.
The headlining assembly must be carried out of the vehicle by multiple people to prevent deformation of the roof headlining assembly.
for Panoramic Moon Roof:
| *a | Fastener | *b | Guide |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the visor holder base as shown in the illustration.
Detach the clip and fastener.
Detach the guide and remove the roof headlining assembly.
Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.
Check that the corners of the roof headlining assembly are free of bending, twisting and other deformation and that none of the mounted parts are falling off.
Do not damage the roof headlining assembly and body interior.
The headlining assembly must be carried out of the vehicle by multiple people to prevent deformation of the roof headlining assembly.
67912A
38.REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH
|
|
|
Remove in this Direction |
|
Protective Tape |
Apply protective tape around the front door scuff plate outside LH.
Insert moulding remover D at the position shown in the illustration and lift in the direction indicated by the arrow to detach the claw and front door scuff plate outside LH.
67911B
39.REMOVE FRONT DOOR SCUFF PLATE RH
|
|
Use the same procedure described for the LH side.
67916
40.REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH
|
|
|
Remove in this Direction |
|
Protective Tape |
Apply protective tape around the rear door scuff plate outside LH.
Insert moulding remover D at the position shown in the illustration and lift in the direction indicated by the arrow to detach the claw and rear door scuff plate outside LH.
67915
41.REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH
|
|
Use the same procedure described for the LH side.