Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2021.08
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455450 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors is detected consecutively 3 times.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2325 LIN Communication Bus Malfunction The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Driver side junction block assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Front multiplex network door ECULH (w/ Reverse Shift-linked Mirror)

·

Front multiplex network door ECURH (w/ Reverse Shift-linked Mirror)

·

Rear multiplex network door ECU LH (for RHD with Double Locking System)

·

Rear multiplex network door ECU LH (for LHD with Door Closer System)

·

Rear multiplex network door ECU RH (for RHD with Double Locking System)

·

Rear multiplex network door ECU RH (for LHD with Door Closer System)

·

Harness or connector

·

Rear power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH


Main Body A

WIRING DIAGRAM

for LHD


C469564E02
2.458,0.813 2.771,1.01 0.313,0.198 10 false 4H 2.458,2.104 2.771,2.302 0.313,0.198 10 false 4H 2.438,1.646 2.75,1.844 0.313,0.198 10 false 4A 2.458,0.615 2.771,0.813 0.313,0.198 10 false 34 2.448,1.469 2.76,1.667 0.313,0.198 10 false 19 2.479,1.896 2.792,2.094 0.313,0.198 10 false 35 1.271,0.667 1.583,0.865 0.313,0.198 10 false 16 0.906,0.823 1.521,1.021 0.615,0.198 10 false LIN2 1.281,2.479 2.51,3.083 1.229,0.604 10 false Driver Side Junction Block Assembly 0.177,2.927 0.333,3.125 0.156,0.198 10 false A 0.177,3.094 1.802,3.667 1.625,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 1.531,4.031 2.146,4.229 0.615,0.198 10 false LIN1 1.521,4.594 2.135,4.792 0.615,0.198 10 false LIN3 1.948,4.063 2.26,4.26 0.313,0.198 10 false 22 1.958,4.615 2.271,4.813 0.313,0.198 10 false 23 0.271,5 0.583,5.198 0.313,0.198 10 false F16 0.302,6.917 0.615,7.115 0.313,0.198 10 false F12 0.302,7.115 2.552,7.521 2.25,0.406 10 false Rear Power Window Regulator Motor Assembly LH 1.583,6.573 2.198,6.771 0.615,0.198 10 false LIN 1.969,6.417 2.281,6.615 0.313,0.198 10 false 9 0.698,8.469 2.479,8.688 1.781,0.219 10 false : LIN Communication Line 5.552,6.406 5.865,6.604 0.313,0.198 10 false 9 5.75,6.563 6.365,6.76 0.615,0.198 10 false LIN 5.313,4.896 5.625,5.094 0.313,0.198 10 false E32 5.292,5.073 6.854,5.75 1.563,0.677 10 false Multiplex Network Master Switch Assembly 5.75,4.208 6.365,4.406 0.615,0.198 10 false LIN1 5.042,6.885 5.354,7.083 0.313,0.198 10 false E20 5.063,7.052 6.969,7.698 1.906,0.646 10 false Front Power Window Regulator Motor Assembly LH 5.5,4.052 5.813,4.25 0.313,0.198 10 false 17 5.292,2.031 5.604,2.229 0.313,0.198 10 false E25 5.292,2.219 6.76,2.771 1.469,0.552 10 false Front Multiplex Network Door ECU LH*1 5.792,0.646 6.406,0.844 0.615,0.198 10 false LIN1 5.75,1.104 6.365,1.302 0.615,0.198 10 false LIN3 5.74,1.563 6.354,1.76 0.615,0.198 10 false LIN2 5.479,0.656 5.792,0.854 0.313,0.198 10 false 11 5.479,1.583 5.792,1.781 0.313,0.198 10 false 12 5.458,1.135 5.771,1.333 0.313,0.198 10 false 13 0.281,7.708 2.865,7.948 2.583,0.24 10 false *1: w/ Reverse Shift-linked Mirror 0.281,8.083 2.625,8.344 2.344,0.26 10 false *2: w/o Reverse Shift-linked Mirror 2.573,4.031 2.885,4.229 0.313,0.198 10 false *3 2.573,4.594 2.885,4.792 0.313,0.198 10 false *3 2.969,4.469 3.281,4.667 0.313,0.198 10 false *4 0.281,5.177 1.729,5.708 1.448,0.531 10 false Rear Multiplex Network Door ECU LH*1 5.75,4.625 6.365,4.823 0.615,0.198 10 false LIN2 5.5,4.448 5.813,4.646 0.313,0.198 10 false 16 5,1.115 5.313,1.313 0.313,0.198 10 false *1 4.99,0.625 5.302,0.823 0.313,0.198 10 false *1 5.01,1.563 5.323,1.76 0.313,0.198 10 false *1 4.646,1.042 4.958,1.24 0.313,0.198 10 false *2 4.656,1.521 4.969,1.719 0.313,0.198 10 false *2 4.365,1.521 4.677,1.719 0.313,0.198 10 false *1 4.635,5.49 4.948,5.688 0.313,0.198 10 false *2 2.708,7.708 6.167,7.917 3.458,0.208 10 false *3: w/ Door Closer System 2.719,8.063 6.24,8.333 3.521,0.271 10 false *4: w/o Door Closer System 4.344,5.479 4.656,5.677 0.313,0.198 10 false *1 2.427,1.24 2.74,1.438 0.313,0.198 10 false 4A 2.427,1.052 2.74,1.25 0.313,0.198 10 false 20

C471323E01
0.594,6.427 2.573,6.625 1.979,0.198 10 false : LIN Communication Line 4.583,1.104 4.896,1.302 0.313,0.198 10 false H4 4.573,1.281 7.094,1.958 2.521,0.677 10 false Sliding Roof Drive Gear Sub-assembly*3 4.625,0.563 4.781,0.76 0.156,0.198 10 false 7 0.073,1.854 0.531,2.052 0.458,0.198 10 false E7 0.073,2 2.646,2.417 2.573,0.417 10 false Front Multiplex Network Door ECU RH 1.24,0.552 1.854,0.75 0.615,0.198 10 false LIN1 1.198,1.281 1.813,1.479 0.615,0.198 10 false LIN3 1.646,1.281 1.958,1.479 0.313,0.198 10 false 13 1.635,0.563 1.948,0.76 0.313,0.198 10 false 11 0.052,3.573 0.51,3.771 0.458,0.198 10 false E2 0.021,3.74 2.323,4.281 2.302,0.542 10 false Front Power Window Regulator Motor Assembly RH 1.302,3.104 1.917,3.302 0.615,0.198 10 false LIN 1.646,2.927 1.802,3.125 0.156,0.198 10 false 9 5.135,2.083 5.75,2.281 0.615,0.198 10 false LIN1 5.135,2.823 5.75,3.021 0.615,0.198 10 false LIN3 4.854,2.083 5.167,2.281 0.313,0.198 10 false 22 4.844,2.813 5.156,3.01 0.313,0.198 10 false 23 4.76,3.375 5.219,3.573 0.458,0.198 10 false F5 4.76,3.573 6.823,4.063 2.063,0.49 10 false Rear Multiplex Network Door ECU RH*4 4.896,5.021 5.354,5.219 0.458,0.198 10 false F1 4.885,5.198 6.729,5.76 1.844,0.563 10 false Rear Power Window Regulator Motor Assembly RH 4.833,0.719 5.448,0.917 0.615,0.198 10 false LIN 4.906,4.448 5.281,4.844 0.375,0.396 10 false 9 0.156,5.906 3.198,6.167 3.042,0.26 10 false *3: w/ Roof Sunshade System 3.583,2.594 3.896,2.792 0.313,0.198 10 false *5 4.25,2.792 4.563,2.99 0.313,0.198 10 false *4 4.25,2.052 4.563,2.25 0.313,0.198 10 false *4 2.948,5.938 6.406,6.292 3.458,0.354 10 false *4: w/ Door Closer System 2.938,6.396 6.542,6.583 3.604,0.188 10 false *5: w/o Door Closer System 0.146,5.052 2.813,5.271 2.667,0.219 10 false *1: w/ Reverse Shift-linked Mirror 0.156,5.469 2.26,5.667 2.104,0.198 10 false *2: w/o Reverse Shift-linked Mirror 2.26,0.531 2.573,0.729 0.313,0.198 10 false *1 2.281,1.281 2.594,1.479 0.313,0.198 10 false *1 2.719,1.083 3.031,1.281 0.313,0.198 10 false *2 5.156,4.646 5.771,4.844 0.615,0.198 10 false LIN


for RHD


C453146E04
2.458,0.813 2.771,1.01 0.313,0.198 10 false 4H 2.458,1.729 2.771,1.927 0.313,0.198 10 false 4H 2.458,1.271 2.771,1.469 0.313,0.198 10 false 4A 2.458,0.615 2.771,0.813 0.313,0.198 10 false 33 2.458,1.083 2.771,1.281 0.313,0.198 10 false 40 2.458,1.531 2.771,1.729 0.313,0.198 10 false 34 1.271,0.667 1.583,0.865 0.313,0.198 10 false 16 0.906,0.823 1.521,1.021 0.615,0.198 10 false LIN2 1.292,2.229 2.917,2.74 1.625,0.51 10 false Driver Side Junction Block Assembly 0.177,2.927 0.333,3.125 0.156,0.198 10 false A 0.177,3.094 1.802,3.667 1.625,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 1.646,4.052 2.26,4.25 0.615,0.198 10 false LIN1 1.635,4.615 2.25,4.813 0.615,0.198 10 false LIN3 2.052,4.073 2.365,4.271 0.313,0.198 10 false 22 2.052,4.604 2.365,4.802 0.313,0.198 10 false 23 0.375,4.969 0.688,5.167 0.313,0.198 10 false F5 0.385,6.833 0.698,7.031 0.313,0.198 10 false F1 0.365,7.01 2.615,7.417 2.25,0.406 10 false Rear Power Window Regulator Motor Assembly RH 1.719,6.583 2.333,6.781 0.615,0.198 10 false LIN 2.042,6.406 2.354,6.604 0.313,0.198 10 false 9 0.698,8.469 2.479,8.688 1.781,0.219 10 false : LIN Communication Line 5.552,6.406 5.865,6.604 0.313,0.198 10 false 9 5.75,6.563 6.365,6.76 0.615,0.198 10 false LIN 5.313,4.896 5.625,5.094 0.313,0.198 10 false E14 5.292,5.073 6.854,5.75 1.563,0.677 10 false Multiplex Network Master Switch Assembly 5.75,4.208 6.365,4.406 0.615,0.198 10 false LIN1 5.042,6.885 5.354,7.083 0.313,0.198 10 false E2 5.063,7.052 6.969,7.698 1.906,0.646 10 false Front Power Window Regulator Motor Assembly RH 5.5,4.052 5.813,4.25 0.313,0.198 10 false 17 5.292,2.031 5.604,2.229 0.313,0.198 10 false E7 5.292,2.219 6.76,2.771 1.469,0.552 10 false Front Multiplex Network Door ECU RH*1 5.792,0.646 6.406,0.844 0.615,0.198 10 false LIN1 5.75,1.104 6.365,1.302 0.615,0.198 10 false LIN3 5.74,1.563 6.354,1.76 0.615,0.198 10 false LIN2 5.479,0.656 5.792,0.854 0.313,0.198 10 false 11 5.479,1.583 5.792,1.781 0.313,0.198 10 false 12 5.458,1.135 5.771,1.333 0.313,0.198 10 false 13 0.281,7.708 2.865,7.948 2.583,0.24 10 false *1: w/ Reverse Shift-linked Mirror 0.281,8.083 2.625,8.344 2.344,0.26 10 false *2: w/o Reverse Shift-linked Mirror 2.573,4.031 2.885,4.229 0.313,0.198 10 false *3 2.573,4.594 2.885,4.792 0.313,0.198 10 false *3 3.458,4.469 3.771,4.667 0.313,0.198 10 false *4 0.375,5.198 1.823,5.729 1.448,0.531 10 false Rear Multiplex Network Door ECU RH*1 5.75,4.625 6.365,4.823 0.615,0.198 10 false LIN2 5.5,4.448 5.813,4.646 0.313,0.198 10 false 16 5,1.115 5.313,1.313 0.313,0.198 10 false *1 4.99,0.625 5.302,0.823 0.313,0.198 10 false *1 5.01,1.563 5.323,1.76 0.313,0.198 10 false *1 4.646,1.042 4.958,1.24 0.313,0.198 10 false *2 4.656,1.521 4.969,1.719 0.313,0.198 10 false *2 4.365,1.521 4.677,1.719 0.313,0.198 10 false *1 4.635,5.49 4.948,5.688 0.313,0.198 10 false *2 2.698,7.719 4.615,7.958 1.917,0.24 10 false *3: w/ Double Locking System 2.719,8.063 4.635,8.302 1.917,0.24 10 false *4: w/o Double Locking System 4.344,5.479 4.656,5.677 0.313,0.198 10 false *1

C453147E03
0.594,6.427 2.573,6.625 1.979,0.198 10 false : LIN Communication Line 5.083,4.896 5.396,5.094 0.313,0.198 10 false H4 5.094,5.052 6.51,5.646 1.417,0.594 10 false Sliding Roof Drive Gear Sub-assembly*5 5.76,4.563 6.375,4.76 0.615,0.198 10 false LIN 5.563,4.417 5.719,4.615 0.156,0.198 10 false 7 0.25,1.74 0.708,1.938 0.458,0.198 10 false E25 0.219,1.917 2.792,2.333 2.573,0.417 10 false Front Multiplex Network Door ECU LH 1.646,0.563 2.26,0.76 0.615,0.198 10 false LIN1 1.635,1.281 2.25,1.479 0.615,0.198 10 false LIN3 2.021,1.281 2.333,1.479 0.313,0.198 10 false 13 2.052,0.563 2.365,0.76 0.313,0.198 10 false 11 0.271,3.365 0.729,3.563 0.458,0.198 10 false E20 0.26,3.563 2.563,4.104 2.302,0.542 10 false Front Power Window Regulator Motor Assembly LH 1.677,3.115 2.292,3.313 0.615,0.198 10 false LIN 2.042,2.948 2.198,3.146 0.156,0.198 10 false 9 5.792,0.573 6.406,0.771 0.615,0.198 10 false LIN1 5.771,1.302 6.385,1.5 0.615,0.198 10 false LIN3 5.5,0.563 5.813,0.76 0.313,0.198 10 false 22 5.5,1.292 5.813,1.49 0.313,0.198 10 false 23 4.979,1.719 5.438,1.917 0.458,0.198 10 false F16 4.969,1.906 7.031,2.396 2.063,0.49 10 false Rear Multiplex Network Door ECU LH*1 5.042,3.406 5.5,3.604 0.458,0.198 10 false F12 5.052,3.552 6.896,4.115 1.844,0.563 10 false Rear Power Window Regulator Motor Assembly LH 5.76,3.115 6.375,3.313 0.615,0.198 10 false LIN 5.531,2.948 5.688,3.146 0.156,0.198 10 false 9 0.146,6.156 3.188,6.417 3.042,0.26 10 false *5: w/ Roof Sunshade System 4.938,0.573 5.25,0.771 0.313,0.198 10 false *3 4.906,1.281 5.219,1.479 0.313,0.198 10 false *3 4.083,1.104 4.396,1.302 0.313,0.198 10 false *4 0.156,5.542 2.823,5.76 2.667,0.219 10 false *3: w/ Double Locking System 0.146,5.833 2.25,6.031 2.104,0.198 10 false *4: w/o Double Locking System 0.156,4.917 2.823,5.135 2.667,0.219 10 false *1: w/ Reverse Shift-linked Mirror 0.156,5.24 2.26,5.438 2.104,0.198 10 false *2: w/o Reverse Shift-linked Mirror 2.802,0.573 3.115,0.771 0.313,0.198 10 false *1 2.771,1.271 3.083,1.469 0.313,0.198 10 false *1 3.083,1.083 3.396,1.281 0.313,0.198 10 false *2


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the GTS and vehicle begins.

·

When the front power window regulator motor assembly LH is removed and reinstalled or replaced, the front power window regulator motor assembly LH must be initialized.



PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is not output A
B2325 is output B



Post-procedure1

a.

None



A

B

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD with Reverse Shift-linked Mirror A
for LHD without Reverse Shift-linked Mirror B
for RHD with Reverse Shift-linked Mirror C
for RHD without Reverse Shift-linked Mirror D



A

3.CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

B

23.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

C

27.CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

D

47.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
3.CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

Pre-procedure1

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B1206 and B2321 are output B



Post-procedure1

a.

None



A

4.CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

B

19.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
4.CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

Pre-procedure1

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2322 is output B



Post-procedure1

a.

None



A

5.CHECK VEHICLE TYPE

B

17.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
5.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Door Closer System A
w/o Door Closer System B



A

6.CHECK REAR MULTIPLEX NETWORK DOOR ECU RH

B

15.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
6.CHECK REAR MULTIPLEX NETWORK DOOR ECU RH

Pre-procedure1

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2323 is output B



Post-procedure1

a.

None



A

7.CHECK REAR MULTIPLEX NETWORK DOOR ECU LH

B

11.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
7.CHECK REAR MULTIPLEX NETWORK DOOR ECU LH

Pre-procedure1

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2324 is output B



Post-procedure1

a.

None



A

8.CHECK VEHICLE TYPE

B

13.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
8.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Roof Sunshade System A
w/o Roof Sunshade System B



A

9.CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

B

10.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
9.CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the H4 sliding roof drive gear sub-assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2329 is output B



Post-procedure1

a.

None



A

10.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

Pre-procedure1

*1: w/ Reverse Shift-linked Mirror

*2: w/ Door Closer System

*3: w/ Roof Sunshade System


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.


b.

Reconnect the driver side junction block assembly connectors.


c.

Disconnect the E25 front multiplex network door ECU LH connector.*1


d.

Disconnect the E7 front multiplex network door ECU RH connector.*1


e.

Disconnect the E32 multiplex network master switch assembly connector.


f.

Disconnect the F16 rear multiplex network door ECU LH connector.*2


g.

Disconnect the F5 rear multiplex network door ECU RH connector.*2


h.

Disconnect the H4 sliding roof drive gear sub-assembly connector.*3


i.

Disconnect the E2 front power window regulator motor assembly RH connector.


j.

Disconnect the E20 front power window regulator motor assembly LH connector.


k.

Disconnect the F1 rear power window regulator motor assembly RH connector.


l.

Disconnect the F12 rear power window regulator motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - Body ground Always 10 kΩ or higher
A-16 (LIN2) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

14.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
11.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the F1 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B2325 is output A
B2323 is output B



A

12.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Disconnect the F1 rear power window regulator motor assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F5,F1)Location & Routing

Click Connector(F5)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU RH

Click Connector(F1)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

F5-23 (LIN3) - F1-9 (LIN) Always Below 1 Ω
F5-23 (LIN3) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the F12 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2324 is output B



Post-procedure1

a.

None



A

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

Pre-procedure1

*1: w/ Reverse Shift-linked Mirror

*2: w/ Door Closer System

*3: w/ Roof Sunshade System


a.

Reconnect the driver side junction block assembly connectors.


b.

Disconnect the E25 front multiplex network door ECU LH connector.*1


c.

Disconnect the E7 front multiplex network door ECU RH connector.*1


d.

Disconnect the E32 multiplex network master switch assembly connector.


e.

Disconnect the F5 rear multiplex network door ECU RH connector.*2


f.

Disconnect the F16 rear multiplex network door ECU LH connector.*2


g.

Disconnect the H4 sliding roof drive gear sub-assembly connector.*3


h.

Disconnect the E2 front power window regulator motor assembly RH connector.


i.

Disconnect the E20 front power window regulator motor assembly LH connector.


j.

Disconnect the F1 rear power window regulator motor assembly RH connector.


k.

Disconnect the F12 rear power window regulator motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-19 - Body ground Always 10 kΩ or higher
4A-19 - Other terminals Always 10 kΩ or higher
4A-20 - Body ground Always 10 kΩ or higher
4A-20 - Other terminals Always 10 kΩ or higher
4H-34 - Body ground Always 10 kΩ or higher
4H-34 - Other terminals Always 10 kΩ or higher
4H-35 - Body ground Always 10 kΩ or higher
4H-35 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the F1 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B2325 is output A
B2323 is output B



A

16.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

16.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the F12 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2324 is output B



Post-procedure1

a.

None



A

8.CHECK VEHICLE TYPE

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

17.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Pre-procedure1

a.

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2322 is output B



Post-procedure1

a.

None



A

18.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

18.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Disconnect the E2 front power window regulator motor assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E7,E2)Location & Routing

Click Connector(E7)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU RH

Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

E7-13 (LIN3) - E2-9 (LIN) Always Below 1 Ω
E7-13 (LIN3) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU FRONT RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the E32 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B1206 is output B



Post-procedure1

a.

None



A

20.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU LH)

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

20.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU LH)

Pre-procedure1

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Disconnect the E32 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E25,E32)Location & Routing

Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LH

Click Connector(E32)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assembly

E25-12 (LIN2) - E32-17 (LIN1) Always Below 1 Ω
E25-12 (LIN2) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

21.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2321 is output B



Post-procedure1

a.

None



A

22.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

22.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Disconnect the E20 front power window regulator motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E25,E20)Location & Routing

Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LH

Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LH

E25-13 (LIN3) - E20-9 (LIN) Always Below 1 Ω
E25-13 (LIN3) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the E32 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B1206 and B2321 are output B



Post-procedure1

a.

None



A

24.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

25.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
24.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Pre-procedure1

a.

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2322 is output B



Post-procedure1

a.

None



A

8.CHECK VEHICLE TYPE

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

25.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2321 is output B



Post-procedure1

a.

None



A

26.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

26.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Disconnect the E32 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E20,E32)Location & Routing

Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LH

Click Connector(E32)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assembly

E20-9 (LIN) - E32-16 (LIN2) Always Below 1 Ω
E20-9 (LIN) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

Pre-procedure1

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B1206 and B2321 are output B



Post-procedure1

a.

None



A

28.CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

B

35.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
28.CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

Pre-procedure1

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2322 is output B



Post-procedure1

a.

None



A

29.CHECK VEHICLE TYPE

B

38.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
29.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Double Locking System A
w/o Double Locking System B



A

30.CHECK REAR MULTIPLEX NETWORK DOOR ECU RH

B

45.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
30.CHECK REAR MULTIPLEX NETWORK DOOR ECU RH

Pre-procedure1

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2323 is output B



Post-procedure1

a.

None



A

31.CHECK REAR MULTIPLEX NETWORK DOOR ECU LH

B

40.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
31.CHECK REAR MULTIPLEX NETWORK DOOR ECU LH

Pre-procedure1

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2324 is output B



Post-procedure1

a.

None



A

32.CHECK VEHICLE TYPE

B

42.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
32.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Roof Sunshade System A
w/o Roof Sunshade System B



A

33.CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

B

34.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
33.CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the H4 sliding roof drive gear sub-assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2329 is output B



Post-procedure1

a.

None



A

34.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

34.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

Pre-procedure1

*1: w/ Reverse Shift-linked Mirror

*2: w/ Double Locking System

*3: w/ Roof Sunshade System


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.


b.

Reconnect the driver side junction block assembly connectors.


c.

Disconnect the E25 front multiplex network door ECU LH connector.*1


d.

Disconnect the E7 front multiplex network door ECU RH connector.*1


e.

Disconnect the E14 multiplex network master switch assembly connector.


f.

Disconnect the E20 front power window regulator motor assembly LH connector.


g.

Disconnect the E2 front power window regulator motor assembly RH connector.


h.

Disconnect the F16 rear multiplex network door ECU LH connector.*2


i.

Disconnect the F5 rear multiplex network door ECU RH connector.*2


j.

Disconnect the F12 rear power window regulator motor assembly LH connector.


k.

Disconnect the F1 rear power window regulator motor assembly RH connector.


l.

Disconnect the H4 sliding roof drive gear sub-assembly connector.*3


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - Body ground Always 10 kΩ or higher
A-16 (LIN2) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

44.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
35.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the E14 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B2325 is output A
B1206 and B2321 are output B



A

36.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

36.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Disconnect the E14 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E7,E12)Location & Routing

Click Connector(E7)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU RH

E7-12 (LIN2) - E12-17 (LIN1) Always Below 1 Ω
E7-12 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

37.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B2325 is output A
B2321 is output B



A

29.CHECK VEHICLE TYPE

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

38.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B2325 is output A
B2322 is output B



A

39.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

39.CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Disconnect the E20 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E25,E20)Location & Routing

Click Connector(E25)Body>Front Door Wire LH / Front Door Wire RH>Front Multiplex Network Door ECU LH

Click Connector(E20)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly LH

E25-13 (LIN3) - E20-9 (LIN) Always Below 1 Ω
E25-13 (LIN3) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the F1 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B2325 is output A
B2323 is output B



A

41.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

41.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the F5 rear multiplex network door ECU RH connector.


b.

Disconnect the F1 rear power window regulator motor assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F5,F1)Location & Routing

Click Connector(F5)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU RH

Click Connector(F1)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

F5-23 (LIN3) - F1-9 (LIN) Always Below 1 Ω
F5-23 (LIN3) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the F12 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2324 is output B



Post-procedure1

a.

None



A

43.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

43.CHECK HARNESS AND CONNECTOR (REAR MULTIPLEX NETWORK DOOR ECU LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the F16 rear multiplex network door ECU LH connector.


b.

Disconnect the F12 rear power window regulator motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F16,F12)Location & Routing

Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

Click Connector(F12)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

F16-23 (LIN3) - F12-9 (LIN) Always Below 1 Ω
F16-23 (LIN3) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

Pre-procedure1

*1: w/ Reverse Shift-linked Mirror

*2: w/ Double Locking System

*3: w/ Roof Sunshade System


a.

Reconnect the driver side junction block assembly connectors.


b.

Disconnect the E25 front multiplex network door ECU LH connector.*1


c.

Disconnect the E7 front multiplex network door ECU RH connector.*1


d.

Disconnect the E14 multiplex network master switch assembly connector.


e.

Disconnect the E2 front power window regulator motor assembly RH connector.


f.

Disconnect the E20 front power window regulator motor assembly LH connector.


g.

Disconnect the F16 rear multiplex network door ECU LH connector.*2


h.

Disconnect the F5 rear multiplex network door ECU RH connector.*2


i.

Disconnect the F12 rear power window regulator motor assembly LH connector.


j.

Disconnect the F1 rear power window regulator motor assembly RH connector.


k.

Disconnect the H4 sliding roof drive gear sub-assembly connector.*3


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-40 - Body ground Always 10 kΩ or higher
4A-40 - Other terminals Always 10 kΩ or higher
4H-33 - Body ground Always 10 kΩ or higher
4H-33 - Other terminals Always 10 kΩ or higher
4H-34 - Body ground Always 10 kΩ or higher
4H-34 - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the F1 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2323 is output B



A

46.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

46.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the F12 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
DTC B2325 is output A
DTC B2324 is output B



Post-procedure1

a.

None



A

32.CHECK VEHICLE TYPE

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

47.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the E14 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B1206 and B2321 are output B



Post-procedure1

a.

None



A

48.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

49.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
48.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the E20 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2322 is output B



Post-procedure1

a.

None



A

29.CHECK VEHICLE TYPE

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

49.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Pre-procedure1

a.

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B2325 is output A
B2321 is output B



Post-procedure1

a.

None



A

50.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

50.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the E2 front power window regulator motor assembly RH connector.


b.

Disconnect the E14 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E2,E14)Location & Routing

Click Connector(E2)Body>Front Door Wire LH / Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

Click Connector(E14)Body>Front Door Wire LH / Front Door Wire RH>Multiplex Network Master Switch Assembly

E2-9 (LIN) - E14-16 (LIN2) Always Below 1 Ω
E2-9 (LIN) - Other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR