Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  High Beam Headlight Circuit  


DESCRIPTION

The headlight ECU sub-assembly controls the high beam headlights.

WIRING DIAGRAM

E475923E01
1.313,2.073 3.458,2.271 2.146,0.198 10 false Headlight Unit 2.521,2.594 4.667,2.792 2.146,0.198 10 false Headlight Unit Assembly 0.875,1.365 3.021,1.563 2.146,0.198 10 false Lo/Hi Beam Shade 5.667,1.146 6.042,1.396 0.375,0.25 10 false B 5.271,2.927 7.125,3.531 1.854,0.604 10 false Headlight ECU Sub-assembly 5.625,1.458 6.042,1.802 0.417,0.344 10 false 11 5.635,0.927 6.01,1.167 0.375,0.24 10 false 20 3.458,1.458 4.208,1.844 0.75,0.385 10 false 2 3.458,0.927 4.208,1.313 0.75,0.385 10 false 3 3.458,1.146 3.823,1.427 0.365,0.281 10 false D 3.458,1.667 3.823,1.948 0.365,0.281 10 false D 5.656,1.667 6.031,1.917 0.375,0.25 10 false B 3.5,2.073 6.26,2.396 2.76,0.323 10 false Headlight Housing Sub-assembly LH

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION


PROCEDURE

1.CHECK LIGHTS
a.

Check the illumination of each high beam lights.


Result:
Result Proceed to
LH side high beam light does not illuminate. A
RH side high beam light does not illuminate. B



A

2.PERFORM ACTIVE TEST USING GTS

B

5.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight High Beam High beam headlights OFF or ON -
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Headlight High Beam
50004 361 6
OK:

High beam headlights turn on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HEADLIGHT UNIT ASSEMBLY LH
3.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Check that the high beam light LH operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK


Result:
Result Proceed to
LH side high beam light does not illuminate. A
RH side high beam light does not illuminate. B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

4.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY LH
4.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY LH
a.

Remove the headlight unit LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Remove the headlight housing sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.
E459081C01
1.448,0.094 1.854,0.427 0.406,0.333 1.521,1.896 1.927,2.229 0.406,0.333 1.625,0.188 1.781,0.385 0.156,0.198 10 false B 1.677,1.99 1.833,2.188 0.156,0.198 10 false D 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 0.594,2 0.906,2.156 0.313,0.156 10 false *b
*a Component without harness connected
(Headlight Unit Assembly LH)
*b Component without harness connected
(Headlight Unit LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-11- D-2 Always Below 1 Ω
B-20 - D-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY LH

5.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight High Beam High beam headlights OFF or ON -
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Headlight High Beam
50004 414 4
OK:

High beam headlights turn on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HEADLIGHT UNIT ASSEMBLY RH
6.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Check that the high beam light RH operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK


Result:
Result Proceed to
RH side high beam light does not illuminate. A
LH side high beam light does not illuminate. B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

7.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY RH
7.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY RH
a.

Remove the headlight unit RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Remove the headlight housing sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.
E459081C01
1.448,0.094 1.854,0.427 0.406,0.333 1.521,1.896 1.927,2.229 0.406,0.333 1.625,0.188 1.781,0.385 0.156,0.198 10 false B 1.677,1.99 1.833,2.188 0.156,0.198 10 false D 0.583,0.146 0.896,0.302 0.313,0.156 10 false *a 0.594,2 0.906,2.156 0.313,0.156 10 false *b
*a Component without harness connected
(Headlight Unit Assembly LH)
*b Component without harness connected
(Headlight Unit LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-11- D-2 Always Below 1 Ω
B-20 - D-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY RH