The hydrogen system of the FC system feeds the FC stack with hydrogen, so that the FC stack can generate power. The hydrogen pump, which is one of the hydrogen system components, circulates a sufficient amount of hydrogen before it will eventually be supplied to the FC stack.
If the actual pump speed does not correspond to a target pump speed, it will be interpreted as a hydrogen pump error, and this DTC will be stored.
For the circuit diagram, refer to DTC P1DC000.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1DC000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1D2496 | Hydrogen Pump Component Internal Failure | Deviation between the actual and target hydrogen pump speeds has continued at a level that exceeds the threshold. While the ignition switch is ON (READY), this malfunction detection is active all the time.
(1 trip detection logic) |
·
Hydrogen recirculation pump assembly ·
Hydrogen pump inverter assembly |
Master Warning: Comes on | EV | B |
| Vehicle Condition | FC shutdown
(ignition switch ON) |
FC startup process | FC intermittent operation | FC is generating power
(vehicle is in stationary) |
FC is generating power
(vehicle is traveling) |
FC shutdown process |
|---|---|---|---|---|---|---|
| Data List
"FC Work Mode" |
Stop | Startup | Working | Finishing | ||
| Data List
"FC Intermittent Operation" |
OFF | ON | OFF | OFF | ||
| DTC Detection | - | ○ | ○ | ○ | ○ | ○ |
By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.
| DTC No. | Data List |
|---|---|
| P1D2496 | ·
Hydrogen Pump Speed ·
Target Hydrogen Pump Speed ·
Hydrogen Pump Main Power Supply Status ·
Hydrogen Pump Output Status ·
Hydrogen Pump Load Status ·
Hydrogen Pump LIN Communication Control ·
Hydrogen Pump CPU Abnormal ·
Hydrogen Pump Start Fail ·
Hydrogen Pump Inverter Over Temperature Status |
| DTC No. | Active Test |
|---|---|
| P1D2496 | Control the Hydrogen Pump |
Refer to DTC P1D8396.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D8396
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.
Make sure to remove the EV supply battery assembly service plug grip first.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the EV supply battery assembly
Disconnecting the low voltage connector of the FC converter assembly
Disconnecting the low voltage connector of the voltage inverter (w/ 1500W Type Voltage Inverter)
After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.
After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION
At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.
Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.
Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL
Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.
When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
Forcing the SOC of the EV supply battery assembly to decrease by applying electrical loads such as turning on the air conditioning (HOT MAX, maximum airflow), or depressing the accelerator pedal with the shift lever in P, the "FC Intermittent Operation" of the Data List is easily to enter OFF (power generation mode).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON (READY) with the shift lever in P, and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF. Then, wait for 1 minute or more.
The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.
Pre-procedure1
None
Procedure1
According to the display on the GTS, check for DTCs in the Health Check.
| Result | Proceed to |
|---|---|
| Only P1D2496 is output | A |
| P1D2496 is output and DTCs other than the DTCs in the table below are output | B |
| P1D2496 is output and any DTCs in the table below are output | C |
| Malfunction Content | Malfunction Content | |
|---|---|---|
| Microcomputer malfunction/Power source circuit malfunction | P1D8396 (EV) | Hydrogen Pump Inverter Component Internal Failure |
| Communication system malfunction | P1D8387 (EV) | Lost Communication with Hydrogen Pump Inverter Missing Message |
| Sensor and actuator circuit malfunction | P1DAA12 (FC) | Exhaust Drainage Valve Circuit Short to Battery |
| P1DAA14 (FC) | Exhaust Drainage Valve Circuit Short to Ground or Open | |
| System malfunction | P1C8449 (Hybrid (EV) Control System) | High Voltage Power Resource Circuit Short during Ready ON |
| P1A0F00 (Hybrid (EV) Control System) | DC/DC Converter "A" Overvoltage (Control Module Performance) | |
| P1A6F00 (Hybrid (EV) Control System) | DC/DC Converter "A" Overvoltage (Inverter Performance) | |
| P1A2F00 (Hybrid (EV) Control System) | DC/DC Converter "A" Overvoltage (Position Sensor Circuit Range/Performance) | |
| P1A7F00 (Hybrid (EV) Control System) | DC/DC Converter "A" Overvoltage (System Performance) | |
| P1A8400 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Overvoltage (Control Module Performance) | |
| P1A8E00 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Overvoltage (Inverter Performance) | |
| P1A8900 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Overvoltage (Position Sensor Circuit Range/Performance) | |
| P1A8F00 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Overvoltage (System Performance) | |
| P31B300 (Hybrid (EV) Control System) | Hybrid/EV Battery Voltage High | |
| P0A944B (Hybrid (EV) Control System) | DC/DC Converter "A" Over Temperature | |
| P1A9400 (Hybrid (EV) Control System) | DC/DC Converter "A" Overcurrent (Control Module Performance) | |
| P1AA400 (Hybrid (EV) Control System) | DC/DC Converter "A" Overcurrent (Inverter Performance) | |
| P1A9900 (Hybrid (EV) Control System) | DC/DC Converter "A" Overcurrent (Position Sensor Circuit Range/Performance) | |
| P1AA900 (Hybrid (EV) Control System) | DC/DC Converter "A" Overcurrent (System Performance) | |
| P0A949E (Hybrid (EV) Control System) | DC/DC Converter "A" Fail Signal Stuck On | |
| P1D824B (Hybrid (EV) Control System) | FC Air Compressor Inverter Over Temperature | |
| P1EF800 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (Control Module Performance) | |
| P1EFB00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (Inverter Performance) | |
| P1EF900 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (Position Sensor Circuit Range/Performance) | |
| P1EFA00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (System Performance) | |
| P1D829E (Hybrid (EV) Control System) | FC Air Compressor Inverter Fail Signal Stuck On | |
| P0A784B (Hybrid (EV) Control System) | Drive Motor "A" Inverter Over Temperature | |
| P1AB400 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Circuit Short (Control Module Performance) | |
| P1ABF00 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Circuit Short (Inverter Performance) | |
| P1AB900 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Circuit Short (Position Sensor Circuit Range/Performance) | |
| P1AC300 (Hybrid (EV) Control System) | Drive Motor "A" Inverter Circuit Short (System Performance) | |
| P0A789E (Hybrid (EV) Control System) | Drive Motor "A" Inverter Fail Signal Stuck On | |
DTC P1D2496 may be output due to problems that cause the DTCs shown above to output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.
Post-procedure1
Turn the ignition switch off.
A
B
C
Hybrid (EV) Control System:
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
None
Procedure1
Read the freeze frame data of DTC P1D2F96.
| Tester Display |
|---|
| Hydrogen Pump Main Power Supply Status |
| Hydrogen Pump Output Status |
| Hydrogen Pump Load Status |
| Hydrogen Pump LIN Communication Control |
| Hydrogen Pump CPU Abnormal |
| Hydrogen Pump Inverter Over Temperature Status |
| Result | Proceed to |
|---|---|
| Other than below. | A |
| The "Hydrogen Pump Output Status" of the freeze frame data shows Circuit Open. | B |
| The "Hydrogen Pump Main Power Supply Status" of the freeze frame data shows Low Voltage or Overvoltage. | C |
| The "Hydrogen Pump Load Status" of the freeze frame data shows Inverter Output Voltage Saturation. | |
| The "Hydrogen Pump CPU Abnormal" of the freeze frame data shows ON. | |
| The "Hydrogen Pump Inverter Over Temperature Status" of the freeze frame data shows Over Temperature. | |
| The "Hydrogen Pump LIN Communication Control" of the freeze frame data shows OFF. | D |
Post-procedure1
Turn the ignition switch off.
A
B
C
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time
D
Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.
Accumulated hydrogen gas could ignite, resulting in a serious accident.
Pre-procedure1
Ensure the safety of the areas in front and at the back of the vehicle.
Put wheel chocks and securely apply the parking brake.
Procedure1
Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working, "FC Intermittent Operation" is OFF, and "Exhaust Drainage Valve" is Close.
| Active Test Display |
|---|
| Activate the Exhaust Drainage Valve |
| Data List Display |
|---|
| FC Work Mode |
| FC Intermittent Operation |
| Exhaust Drainage Valve |
| *1 | Tailpipe |
| *2 | Hydrogen Gas Detector Probe |
Use the hydrogen gas detector to measure and record the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is closed.
Perform this measurement in an environment where there is no wind.
Position the hydrogen gas detector probe in an area 100 mm (3.94 in.) away from the tailpipe opening. (Avoid locations underneath the tailpipe opening)
Position the hydrogen gas detector probe so that it is free from dropping water that comes from the tailpipe opening.
Perform the "Activate the Exhaust Drainage Valve" Active Test several times over 1 minute, and then, starting from the third test, use the hydrogen gas detector to measure the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is open.
The exhaust drainage valve will open for 1 second each time the Active Test is performed, so measure the hydrogen concentration for several seconds.
Hydrogen concentration may not increase while coolant escapes when the valve is first opened. Therefore, start measuring from the third test.
There is a delayed response when performing detection using the hydrogen gas detector, so measure for several seconds.
"FC Intermittent Operation" in the Data List will be more likely to turn OFF if the accelerator pedal is depressed with the shift state in park (P).
| Result | Proceed to |
|---|---|
| The hydrogen concentration of the hydrogen gas detector will increase when "Exhaust Drainage Valve" in the Data List is Open rather than when "Exhaust Drainage Valve" is Close. | A |
| Other than above* | B |
*: The exhaust drainage valve is malfunctioning
Exhaust drainage valve is stuck closed:
Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained low.
Exhaust drainage valve is stuck open:
Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained high when the ignition switch is on (READY).
Post-procedure1
Turn the ignition switch off.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON (READY).
Procedure1
Check the "Target Hydrogen Pump Speed" and "Hydrogen Pump Speed" of the Data List during an Active Test.
| Active Test Display |
|---|
| Control the Hydrogen Pump |
| Data List Display |
|---|
| Hydrogen Pump Drive Speed |
| Hydrogen Pump Speed |
| Target Hydrogen Pump Speed |
| Hydrogen Pump Load Status |
| Hydrogen Pump Start Fail |
| - | Hydrogen Pump (Active Test) | |
|---|---|---|
| 1000 rpm | 2000 rpm | |
| Target Hydrogen Pump Speed
(Data List) |
1000 rpm | 2000 rpm |
| Hydrogen Pump Speed
(Data List) |
800 to 1200 rpm | 1800 to 2200 rpm |
"Target Hydrogen Pump Speed" and "Hydrogen Pump Speed" change according to the command of the Active Test, and no malfunctions are shown for other Data List items.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.
After removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the hydrogen recirculation pump assembly connector from the hydrogen pump inverter assembly.
Procedure1
| *1 | Shield Ground |
| *a | Front view of wire harness connector
(to Hydrogen Pump Assembly) |
Check the hydrogen pump assembly for an interphase short using a milliohmmeter.
Using a milliohmmeter, measure the resistance according to the value(s) in the table below.
If the hydrogen pump assembly temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z30)Location & Routingewd_type=routing;type=c;code=z30 Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assemblyewd_type=component;type=c;code=z30;pinno=3,2,1 |
||
| z30-3 (W) - z30-2 (V) | Ignition switch off | 622 to 762 mΩ |
| z30-3 (W) - z30-1 (U) | Ignition switch off | 622 to 762 mΩ |
| z30-2 (V) - z30-1 (U) | Ignition switch off | 622 to 762 mΩ |
To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).
R20 = Rt / {1 + 0.00393 X (T - 20)}
The calculation is based on the following:
R20: Resistance at 20°C (68°F) (mΩ)
Rt: Measured resistance (mΩ)
T: Temperature when the resistance is measured (°C (°F))
Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(z30)Location & Routingewd_type=routing;type=c;code=z30 Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assemblyewd_type=component;type=c;code=z30;pinno=3,2,1 |
||
| z30-3 (W) - Body ground and shield ground | Ignition switch off | 50 MΩ or higher |
| z30-2 (V) - Body ground and shield ground | Ignition switch off | 50 MΩ or higher |
| z30-1 (U) - Body ground and shield ground | Ignition switch off | 50 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the hydrogen recirculation pump assembly connector to the hydrogen pump inverter assembly.
OK
Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL
Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time
NG