The occupant detection sensor (separate type front seat cushion pad) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (front passenger side) detects the passenger seat belt condition and sends signals to the combination meter assembly or airbag sensor assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt assembly (front passenger seat), the seat belt warning light on the combination meter assembly will blink or go off.
w/ Occupant Classification System
w/o Occupant Classification System
The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK
If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Occupant Classification System | A |
| w/ Occupant Classification System | B |
A
B
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ All Auto Control | A |
| w/o All Auto Control | B |
A
B
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Occupant Detection Switch | Occupant detection sensor signal | OFF or ON | OFF: Front passenger seat not occupied
ON: Front passenger seat occupied |
- |
| Tester Display |
|---|
| Passenger Occupant Detection Switch |
The GTS display changes correctly in response to the front passenger seat condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the D41 combination meter assembly connector.
Disconnect the G27*1 or G25*2 front seat inner belt assembly (for Front Passenger Side) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D41,G27)Location & Routingewd_type=routing;type=c,c;code=D41,G27 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=6 Click Connector(G27)Seat>Floor Wire>Front Seat Inner Belt Assembly RHewd_type=component;type=c;code=G27;pinno=6,5 |
||
| D41-6 (PODS) - G27-6 (+) | Always | Below 1 Ω |
| D41-6 (PODS) or G27-6 (+) - Body ground | Always | 10 kΩ or higher |
| G27-5 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D41,G25)Location & Routingewd_type=routing;type=c,c;code=D41,G25 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=6 Click Connector(G25)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=G25;pinno=6,5 |
||
| D41-6 (PODS) - G25-6 (+) | Always | Below 1 Ω |
| D41-6 (PODS) or G25-6 (+) - Body ground | Always | 10 kΩ or higher |
| G25-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Passenger Buckle Switch | Front passenger seat belt buckle switch signal | OFF or ON | OFF: Front passenger seat belt fastened
ON: Front passenger seat belt not fastened |
- |
| Passenger Occupant Detection Switch | Occupant detection sensor signal | OFF or ON | OFF: Front passenger seat not occupied
ON: Front passenger seat occupied |
- |
| Tester Display |
|---|
| Passenger Buckle Switch |
| Passenger Occupant Detection Switch |
The GTS display changes correctly in response to the front passenger seat belt and front passenger seat condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Passenger Occupant Detection Switch) | B |
| NG (Passenger Buckle Switch) | C |
A
B
C
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Disconnect the D41 combination meter assembly connector.
Disconnect the G28*1 or G26*2 front seat inner belt assembly (for Front Passenger Side) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D41,G28)Location & Routingewd_type=routing;type=c,c;code=D41,G28 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=6 Click Connector(G28)Seat>Floor Wire>Front Seat Inner Belt Assembly RHewd_type=component;type=c;code=G28;pinno=5,4 |
||
| D41-6 (PODS) - G28-5 (+) | Always | Below 1 Ω |
| D41-6 (PODS) or G28-5 (+) - Body ground | Always | 10 kΩ or higher |
| G28-4 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D41,G26)Location & Routingewd_type=routing;type=c,c;code=D41,G26 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=6 Click Connector(G26)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=G26;pinno=5,4 |
||
| D41-6 (PODS) - G26-5 (+) | Always | Below 1 Ω |
| D41-6 (PODS) or G26-5 (+) - Body ground | Always | 10 kΩ or higher |
| G26-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the D41 combination meter assembly connector.
Disconnect the G28*1 or G26*2 front seat inner belt assembly (for Front Passenger Side) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D41,G28)Location & Routingewd_type=routing;type=c,c;code=D41,G28 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=18 Click Connector(G28)Seat>Floor Wire>Front Seat Inner Belt Assembly RHewd_type=component;type=c;code=G28;pinno=3,2 |
||
| D41-18 (PBKL) - G28-3 (+) | Always | Below 1 Ω |
| D41-18 (PBKL) or G28-3 (+) - Body ground | Always | 10 kΩ or higher |
| G28-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D41,G26)Location & Routingewd_type=routing;type=c,c;code=D41,G26 Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assemblyewd_type=component;type=c;code=D41;pinno=18 Click Connector(G26)Seat>Floor Wire>Front Seat Inner Belt Assembly LHewd_type=component;type=c;code=G26;pinno=3,2 |
||
| D41-18 (PBKL) - G26-3 (+) | Always | Below 1 Ω |
| D41-18 (PBKL) or G26-3 (+) - Body ground | Always | 10 kΩ or higher |
| G26-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART