Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A9000  Drive Motor "A" Performance  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC indicates that magnetic force deterioration of the permanent magnet located in the rotor inside the motor has been detected. The cause of this malfunction may be one of the following:

Area Main Malfunction Description
Inverter low-voltage circuit The connectors are not connected properly
EV control ECU EV control ECU internal circuit malfunction
Inside of inverter Inverter with converter assembly internal circuit malfunction
FCV with motor transaxle assembly (including motor cable)
·

Internal motor malfunction (entry of foreign matter, etc.)

·

Motor permanent magnet magnetic force deterioration

·

Open or short circuit in the motor coils

·

Defective motor cable connection

·

Open circuit or poor insulation on motor cable




DESCRIPTION

When three-phase alternating current flows through the three-phase windings of the stator coil, a rotating magnetic field is generated in the motor. The system controls the rotation of the magnetic field in accordance with the rotating position and speed of the rotor. As a result, the permanent magnets provided in the rotor are pulled in the direction of rotation, generating torque. The generated torque is almost proportional to the amount of current. The system controls motor speed by regulating the frequency of the alternating current. Furthermore, the system properly controls the rotating magnetic field and the angle of the rotor magnets in order to generate high torque in an efficient manner, even at high speeds.

HINT:

The term "drive motor A" indicates the motor (MG2).


A283318E03
2.302,1.375 1.583,1.375 false 3.875,0.74 3.385,0.74 3.385,0.74 2.979,1.219 false 4.302,1.417 3.083,1.906 false 4.677,1.792 3.698,1.792 3.698,1.792 3.49,1.958 false 3.021,3.344 3.021,2.594 false 1.958,0.271 2.646,0.5 0.688,0.229 10 U Phase 0.958,3.135 1.646,3.365 0.688,0.229 10 V Phase 4.771,2.615 5.458,2.844 0.688,0.229 10 W Phase 3.26,0.323 3.948,0.552 0.688,0.229 10 # 1.396,2.458 2.083,2.688 0.688,0.229 10 # 4.188,3.073 4.875,3.302 0.688,0.229 10 # 0.094,1.292 1.667,1.49 1.573,0.198 10 Rotating Magnetic Field 3.938,0.667 4.74,0.896 0.802,0.229 10 Stator Coil 4.333,1.323 4.833,1.552 0.5,0.229 10 Rotor 4.729,1.719 5.479,2 0.75,0.281 10 Reaction 2.729,3.333 3.49,3.615 0.76,0.281 10 Attraction 5.656,2.938 6.615,3.146 0.958,0.208 10 : from inverter 5.583,3.198 6.833,3.479 1.25,0.281 10 #: wired in motor

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A9000 Drive Motor "A" Performance Motor magnetic force deterioration or same phase short circuit:
Magnetic force of the motor decreases or a coil circuit in one of the 3 phases remains shorted for a certain period of time.
(1 trip detection logic)
·

FCV with motor transaxle assembly

·

Inverter with converter assembly

·

Wire harness or connector

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0A9000 Motor Maximum Temperature

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Drive the vehicle until the cumulative traveling time driving at a vehicle speed of 50 km/h (31 mph) or more is a few minutes (It is not necessary to drive continuously at 50 km/h (31 mph) or more).

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the motor high-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor High-voltage Circuit

Refer to the wiring diagram for the shut down signal circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0A9000 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Malfunction Content Relevant DTC
Insulation Malfunction P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1EEC49 Hybrid/EV Battery Voltage System Isolation (FC Air Compressor Area) Internal Electronic Failure
P1EED49 Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure
P1EEE49 Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure
P1EEF49 Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure
High Voltage Circuit Malfunction P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P1C8449 High Voltage Power Resource Circuit Short during Ready ON

HINT:
·

P0A9000 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.SIMULATION TEST

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.SIMULATION TEST

Pre-procedure1

a.

Drive the vehicle at a speed of 50 km/h (31 mph) for approximately 1 minute.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0A9000 is output or no DTCs are output. A
Except P0A9000 is output. B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK SHUT DOWN SIGNAL CIRCUIT

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SHUT DOWN SIGNAL CIRCUIT

NEXT

5.CHECK MOTOR HIGH-VOLTAGE CIRCUIT
5.CHECK MOTOR HIGH-VOLTAGE CIRCUIT

NEXT