Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AA000  Hybrid/EV Battery Positive Contactor Circuit Stuck Closed  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects a stuck closed malfunction of a system main relay on the EV supply battery assembly positive (+) terminal side.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

No. 1 EV battery junction block assembly malfunction


Low-voltage circuit (12 V) malfunction
·

EV control ECU malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0AA000 Hybrid/EV Battery Positive Contactor Circuit Stuck Closed Even the system main relay of EV supply battery assembly positive (+) terminal side is turned off, the inverter voltage (VH) does not drop.
(1 trip detection logic)
·

No. 1 EV battery junction block assembly

·

Inverter with converter assembly

·

EV control ECU

·

Wire harness or connector


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0AA000
·

Hybrid/EV Battery Voltage

·

VH-Voltage after Boosting

·

VL-Voltage before Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 100 V, the vehicle has returned to normal.


4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

If DTC P0AA000 is output, the ignition switch cannot be turned to ON (READY).


PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0AA000 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P1C9E9F Hybrid/EV System Reset Stuck Off
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance
P0A1B04 Drive Motor "A" Control Module System Internal Failure
P1CA700 Drive Motor "A" Control Module RAM/ROM Error
P1CAD49 Drive Motor "A" Control Module Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error
P1D8F04 FC Air Compressor Motor Control Module System Internal Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure
P1C731C Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
Power source circuit malfunction P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06B01C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
Communication system malfunction P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
Sensor and actuator circuit malfunction P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A1B00 Drive Motor "A" Control Module Performance
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P1D8F00 FC Air Compressor Motor Control Module Performance
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
System malfunction P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Overvoltage Signal Stuck On
P1E1500 FC Positive Contactor Actuator Stuck Closed
P1E1773 FC Negative Contactor Control Actuator Stuck Closed
P1E1573 FC Positive and Negative Contactor Actuator Stuck Closed

HINT:
·

P0AA000 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (EV)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK FREEZE FRAME DATA (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P0AA000.

Powertrain > EV
Tester Display Measurement Item Range
VL-Voltage before Boosting High voltage before it is boosted -
VH-Voltage after Boosting High voltage after it is boosted -
Powertrain > EV > DTC(P0AA000) > Freeze Frame Data
Tester Display
VL-Voltage before Boosting
VH-Voltage after Boosting
50040 397 150,151 P0AA000
NOTICE:

As freeze frame data is stored immediately before and after a DTC is stored, make sure to only read the values for the moment the DTC was stored ("0(s)").


Result:
Result Proceed to
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is less than 42 V. A
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is 42 V or more. B


HINT:

If VH-Voltage after Boosting is output even when an off command is being sent to the system main relay (positive side), P0AA000 is output. If the difference between the "VL-Voltage before Boosting" and the "VH-Voltage after Boosting" is large, it is determined that there is an inverter (VH sensor) malfunction.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014

Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

OK (for RHD)

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

NG

4.CONNECT SECURELY
4.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)
a.
A484682C02
0.865,0.656 1.385,1.063 0.521,0.406 0.667,3.208 1.188,3.615 0.521,0.406 0.99,0.76 1.323,0.948 0.333,0.188 10 true AG2 0.01,0 0.323,0.198 0.313,0.198 10 true *A 0,2.438 0.313,2.635 0.313,0.198 10 true *B 0.802,3.333 1.135,3.521 0.333,0.188 10 true AG2
*A for LHD
*B for RHD


Check the connection condition of the AG2 No. 2 floor wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

B

6.CONNECT SECURELY

C

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)
8.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)
a.
A479481E01
0.708,0.25 1.229,0.646 0.521,0.396 0.771,0.344 1.146,0.542 0.375,0.198 10 true G156

Check the connection condition of the G156 No. 2 EV battery pack wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

9.CONNECT SECURELY

C

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
11.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
A478500E01
2.021,0.375 2.469,0.698 0.448,0.323 2.135,0.458 2.375,0.604 0.24,0.146 10 true z24

Check the connector connections and contact pressure of the relevant terminals of the No. 1 EV battery junction block assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 10 EV battery shield panel.



OK

13.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)

NG

12.CONNECT SECURELY
12.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

13.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
13.CHECK GROUND WIRE CONNECTION CONDITION (SMR ACTIVATION LOW-VOLTAGE CIRCUIT)
a.

Check the installation condition of the ground wire GG.

OK:

The ground wire GG is securely installed.



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

14.CONNECT SECURELY
14.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

15.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
15.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the z24 No. 1 EV battery junction block assembly connector.


d.

Disconnect the G14*1 or A14*2 EV Control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A479459C27
2.531,3.51 3.01,3.885 0.479,0.375 0.885,1.833 1.365,2.146 0.479,0.313 0.885,1.448 1.365,1.76 0.479,0.313 1.042,4.24 1.375,3.823 true 0.844,2.313 0.469,1.75 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.198,2.76 0.51,2.958 0.313,0.198 10 false *b 2.677,3.615 2.99,3.813 0.313,0.198 10 false z24 0.854,2.365 1.313,2.531 0.458,0.167 10 false SMRB 0.823,4.302 1.375,4.51 0.552,0.208 10 false SMRB 0.958,1.5 1.417,1.698 0.458,0.198 10 false G14 0.969,1.906 1.427,2.104 0.458,0.198 10 false A14 1.427,1.49 1.74,1.688 0.313,0.198 10 false *A 1.417,1.896 1.729,2.094 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,z24)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

G14-4 (SMRB) - z24-1 (SMRB) Ignition switch off Below 1 Ω
G14-4 (SMRB) and z24-1 (SMRB) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,z24)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

A14-4 (SMRB) - z24-1 (SMRB) Ignition switch off Below 1 Ω
A14-4 (SMRB) and z24-1 (SMRB) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV Control ECU connector.

*1: for LHD

*2: for RHD


b.

Reconnect the z24 No. 1 EV battery junction block assembly connector.


c.

Install the No. 10 EV battery shield panel.



OK

17.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

17.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
17.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the z24 No. 1 EV battery junction block assembly connector.


Procedure1

a.
C385344C11
2.635,1.052 3.115,1.375 0.479,0.323 2.198,1.75 1.885,1.302 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 2.781,1.135 3.094,1.333 0.313,0.198 10 false z24 2.198,1.813 2.552,1.99 0.354,0.177 10 false GND
*a Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z24)Location & Routing

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z24-3 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z24 No. 1 EV battery junction block assembly connector.


b.

Install the No. 10 EV battery shield panel.



OK

19.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

18.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

19.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
19.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478500E01
2.021,0.375 2.469,0.698 0.448,0.323 2.135,0.458 2.375,0.604 0.24,0.146 10 true z24

Disconnect the z24 No. 1 EV battery junction block assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479455C09
3.844,0.99 4.24,1.281 0.396,0.292 3.385,1.188 3.094,1.354 true 3.604,1.188 3.844,1.375 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 3.958,1.063 4.271,1.219 0.313,0.156 10 false z24 3.708,1.385 4.135,1.552 0.427,0.167 10 true SMRB 2.927,1.385 3.24,1.552 0.313,0.167 10 true GND
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z24)Location & Routing

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z24-1 (SMRB) - z24-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z24 No. 1 EV battery junction block assembly connector.


b.

Install the No. 10 EV battery shield panel.



OK

20.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

22.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
20.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478501E01
2.083,0.125 2.469,0.417 0.385,0.292 2.219,0.208 2.531,0.406 0.313,0.198 10 false N1

Disconnect the N1 floor under wire connector from the No. 1 EV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
A479456E01
2.333,0.104 2.792,0.438 0.458,0.333 2.469,0.208 2.927,0.406 0.458,0.198 10 false z13

Disconnect the EV supply battery assembly high voltage connector from the No. 1 EV battery junction block assembly.

CAUTION:

Disconnect the EV supply battery assembly high voltage connector from the No. 1 EV battery junction block assembly.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479458C01
5.333,0.146 5.75,0.458 0.417,0.313 3.74,0.135 4.156,0.448 0.417,0.313 5.125,0.917 5.563,1.219 true 3.469,0.906 3.76,1.083 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 3.813,1.104 4.125,1.302 0.313,0.198 10 true CBI 5.448,0.229 5.76,0.427 0.313,0.198 10 false z13 3.885,0.229 4.198,0.427 0.313,0.198 10 false N1 5.646,1.198 5.958,1.396 0.313,0.198 10 false +
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z13,N1)Location & Routing

Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

z13-1 (+) - N1-1 (CBI) Ignition switch off 10 kΩ or higher


HINT:
·

If a system main relay is stuck closed, inspect the No. 1 EV battery junction block assembly without removing it from the vehicle, in order to keep the relay closed.

·

If the result of reading the freeze frame data is A, the No. 1 EV battery junction block assembly must be replaced. Measuring resistance can determine that this is either a present or past malfunction.



Result:
Result Judgment Proceed to
OK Past malfunction A
NG Present malfunction B



Post-procedure1

a.

Reconnect the EV supply battery assembly high voltage connector.


b.

Reconnect the floor under wire connector.


c.

Install the No. 10 EV battery shield panel.



A

21.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

B

23.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
21.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

24.CLEAR DTC
22.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

25.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)
23.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

24.CLEAR DTC
24.CLEAR DTC
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

install the service plug grip.


Procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

25.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)
25.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > EV > Data List
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50003 397 150,227
Result:
Result Proceed to
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 100 V. A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B

REPLACE EV CONTROL ECU AND NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY