Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module)
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0340  Camshaft Position Sensor Circuit Malfunction  


DESCRIPTION

The cam position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft timing rotor passes through the cam position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the cam position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No. DTC Detection Condition Trouble Area
P0340 Either of the following conditions is met (1 trip detection logic):
·

No cam position sensor signal to the ECM at an engine speed of 600 rpm or higher.

·

A missing cam position sensor signal despite the crank position sensor inputs being normal at an engine speed of 600 rpm or higher.


·

Open or short in cam position sensor circuit

·

Cam position sensor

·

Intake camshaft

·

Valve timing

·

ECM




MONITOR DESCRIPTION

If no pulse signal is transmitted by the cam position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Cam position sensor
Required Sensors/Components (Related) Crank position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0340.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.



PROCEDURE

1.INSPECT CAM POSITION SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (CAM POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CAM POSITION SENSOR - ECM)
a.

Disconnect the cam position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C13-1 - C10-82 (VV1+) Always Below 1 Ω
C13-2 - C10-114 (VV1-) Always Below 1 Ω
C13-1 or C10-82 (VV1+) - Body ground Always 10 kΩ or higher
C13-2 or C10-114 (VV1-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C13-1 - C9-82 (VV1+) Always Below 1 Ω
C13-2 - C9-114 (VV1-) Always Below 1 Ω
C13-1 or C9-82 (VV1+) - Body ground Always 10 kΩ or higher
C13-2 or C9-114 (VV1-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (CAM POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAM POSITION SENSOR)
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the cam position sensor installation.

OK:

Cam position sensor is installed correctly.




OK

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE CAM POSITION SENSOR

NG

6.REPLACE CAM POSITION SENSOR

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / DTC.


l.

Read the DTCs.

Result
Result Proceed to
DTC P0340 is output A
DTC is not output B

HINT:

If the engine does not start, replace the ECM.




A

B

END