When foreign matter adheres to the speed sensor tip or speed sensor rotor, these DTCs are stored. The presence of foreign matter can be judged when an abnormal waveform is received from the sensor.
These DTCs may also be detected when a malfunction occurs in the connector terminals or wire harness of the speed sensor circuit.
DTCs C1275/75 to C1278/78 will be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs from C1275/75 to C1278/78 are output only in Test Mode.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1235/35 | 541 | Either of the following is detected:
1.
When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more. 2.
When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more. |
·
Speed sensor rotor malfunction (foreign object attached) ·
Foreign object attached to speed sensor ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Resistance in speed sensor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1236/36 | 542 | Either of the following is detected:
1.
When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more. 2.
When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more. |
·
Speed sensor rotor malfunction (foreign object attached) ·
Foreign object attached to speed sensor ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Resistance in speed sensor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1238/38 | 543 | Either of the following is detected:
1.
When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more. 2.
When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more. |
·
Speed sensor rotor malfunction (foreign object attached) ·
Foreign object attached to speed sensor ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Resistance in speed sensor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1239/39 | 544 | Either of the following is detected:
1.
When driving at 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more. 2.
When driving at 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more. |
·
Speed sensor rotor malfunction (foreign object attached) ·
Foreign object attached to speed sensor ·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Resistance in speed sensor circuit ·
Skid control ECU (Brake booster with master cylinder assembly) |
| C1275/75
C1276/76 |
- | Detected only during Test Mode. | ·
Front speed sensor RH/LH ·
Front speed sensor rotor RH/LH (Front axle hub bearing RH/LH) |
| C1277/77
C1278/78 |
- | Detected only during Test Mode. | ·
Rear speed sensor RH/LH ·
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
DTCs C1235/35 and C1275/75 are for the front speed sensor RH.
DTCs C1236/36 and C1276/76 are for the front speed sensor LH.
DTCs C1238/38 and C1277/77 are for the rear speed sensor RH.
DTCs C1239/39 and C1278/78 are for the rear speed sensor LH.
Refer to DTCs C1464/31, C1465/32, C1466/33 and C1467/34 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1271/71 for front, and Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1273/73 for rear).
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check that no speed sensor malfunction DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
When C1464/31, C1465/32, C1466/33, and/or C1467/34 are output together with C1235/35, C1236/36, C1238/38, and/or C1239/39, inspect and repair the trouble areas indicated by C1464/31, C1465/32, C1466/33, and/or C1467/34 first.
| Result | Proceed to |
|---|---|
| DTCs C1235/35 and/or C1236/36 are output. | A |
| DTCs C1238/38 and C1239/39 are output. | B |
| Speed sensor malfunction DTCs (C1464/31, C1465/32, C1466/33 and/or C1467/34) are output. | C |
A
B
C
Remove the front speed sensor and the component with the sensor rotor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL and Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).
Check the speed sensor tip and speed sensor rotor.
The sensor tip and rotor is free of scratches, oil, and foreign matter.
If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
OK
NG
Install the front speed sensor and the component with the sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-18 (FR+) - A21-2 (FR+) | Always | Below 1 Ω |
| A41-18 (FR+) - Body ground | Always | 10 kΩ or higher |
| A41-5 (FR-) - A21-1 (FR-) | Always | Below 1 Ω |
| A41-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-31 (FL+) - A22-2 (FL+) | Always | Below 1 Ω |
| A41-31 (FL+) - Body ground | Always | 10 kΩ or higher |
| A41-32 (FL-) - A22-1 (FL-) | Always | Below 1 Ω |
| A41-32 (FL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-2 (FR+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A22-2 (FL+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the power switch off (lock).
Reconnect the front speed sensor connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1235/35 and/or C1236/36 are output. | A |
| DTCs C1235/35 and C1236/36 are not output. | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the power switch off (lock).
Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1235/35 and/or C1236/36 are output. | A |
| DTCs C1235/35 and C1236/36 are not output. | B |
A
B
Turn the power switch off (lock).
Replace the front speed sensor rotor (front axle hub bearing) (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).
The front speed sensor rotor is incorporated into the front axle hub bearing.
If the front speed sensor rotor needs to be replaced, replace the front axle hub bearing.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1235/35 and/or C1236/36 are output (for LHD). | A |
| DTCs C1235/35 and/or C1236/36 are output (for RHD). | B |
| DTCs C1235/35 and C1236/36 are not output. | C |
A
B
C
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the rear speed sensor connector and the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W1-2 (RR+) - WM1-1 (RR+) | Always | Below 1 Ω |
| W1-2 (RR+) - WM1-2 (RR-) | Always | 10 kΩ or higher |
| W1-2 (RR+) - Body ground | Always | 10 kΩ or higher |
| W1-1 (RR-) - WM1-2 (RR-) | Always | Below 1 Ω |
| W1-1 (RR-) - WM1-1 (RR+) | Always | 10 kΩ or higher |
| W1-1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X1-2 (RL+) - XM1-1 (RL+) | Always | Below 1 Ω |
| X1-2 (RL+) - XM1-2 (RL-) | Always | 10 kΩ or higher |
| X1-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| X1-1 (RL-) - XM1-2 (RL-) | Always | Below 1 Ω |
| X1-1 (RL-) - XM1-1 (RL+) | Always | 10 kΩ or higher |
| X1-1 (RL-) - Body ground | Always | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *a | Front view of skid control sensor wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-22 (RR+) - WM1-1 (RR+) | Always | Below 1 Ω |
| A41-22 (RR+) - Body ground | Always | 10 kΩ or higher |
| A41-9 (RR-) - WM1-2 (RR-) | Always | Below 1 Ω |
| A41-9 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-20 (RL+) - XM1-1 (RL+) | Always | Below 1 Ω |
| A41-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A41-7 (RL-) - XM1-2 (RL-) | Always | Below 1 Ω |
| A41-7 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| WM1-1 (RR+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| XM1-1 (RL+) - Body ground | Power switch on (IG) | 5.7 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control Sensor Wire) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the power switch off (lock).
Reconnect the rear speed sensor connector and the skid control sensor wire.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1238/38 and/or C1239/39 are output. | A |
| DTCs C1238/38 and C1239/39 are not output. | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the power switch off (lock).
Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1238/38 and/or C1239/39 are output (for LHD). | A |
| DTCs C1238/38 and/or C1239/39 are output (for RHD). | B |
| DTCs C1238/38 and C1239/39 are not output. | C |
A
B
C