Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1246/46  Master Cylinder Pressure Sensor Malfunction  C1281/81  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1364/61  Wheel Cylinder Pressure Sensor Malfunction  


DESCRIPTION

The regulator pressure sensor and wheel cylinder pressure sensor are built into the brake actuator. They measure their respective pressures and send signals to the skid control ECU.

DTC C1281/81 will be cleared when the regulator pressure sensor sends a regulator pressure signal or when Test Mode ends. DTC C1281/81 is output only in Test Mode.

DTC No. INF Code DTC Detection Condition Trouble Area
C1246/46 201 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds. Brake booster with master cylinder assembly
↑ 202 Regulator pressure sensor output voltage (Preg) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more. ↑
↑ 203 When not under braking, the regulator pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 3 seconds or more. ↑
↑ 204 Either of the following is detected:
1.

The regulator pressure sensor output voltage does not correspond with brake pedal stroke sensor assembly and the readings remain out of specification for 0.5 to 5 seconds or more continuously.

(The brake pedal stroke sensor assembly may be malfunctioning.)

2.

The regulator pressure sensor output voltage does not correspond with wheel cylinder pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.

(May be output with INF code 424.)


·

Brake pedal stroke sensor assembly

·

Brake booster with master cylinder assembly


↑ 207 Fluctuation of regulator pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more. Brake booster with master cylinder assembly
C1364/61 421 Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 422 Wheel cylinder pressure sensor output voltage (Pfront) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more. ↑
↑ 423 When not under braking, the wheel cylinder pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 0.1 to 3 seconds or more. ↑
↑ 424 The wheel cylinder pressure sensor output voltage does not correspond with regulator pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.
(May be output with INF code 204.)
↑
↑ 426 Fluctuation of wheel cylinder pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more. ↑
C1281/81 - Detected only during Test Mode.
·

Stop light switch assembly

·

Regulator pressure sensor (Brake booster with master cylinder assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the protrusion of the rod (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).

OK:

Stop light switch assembly is installed properly.


HINT:

If the stop light switch assembly is not installed properly, adjust the protrusion of the rod before proceeding to the next step.




OK

2.READ VALUE USING INTELLIGENT TESTER (REGULATOR PRESSURE SENSOR)

NG

2.READ VALUE USING INTELLIGENT TESTER (REGULATOR PRESSURE SENSOR)
a.

Mount a pedal effort gauge and install LSPV gauges to the rear wheels (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Output Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


e.

Check the output value of the regulator pressure sensor as the brake pedal is depressed.

Standard Voltage:
Brake Effort
(N (kgf, lbf))
Regulator Pressure Sensor Output
(V)
Rear Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Rear Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
100 (10, 22.5) 1.55 to 2.35 5.08 to 9.08 (51.9 to 92.5, 737 to 1317) 5.08 to 9.08 (51.9 to 92.5, 737 to 1317)
200 (20, 45.0) 3.47 to 4.27 14.49 to 18.49 (147.8 to 188.5, 2102 to 2681) 14.49 to 18.49 (147.8 to 188.5, 2102 to 2681)


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.READ VALUE USING INTELLIGENT TESTER (WHEEL CYLINDER PRESSURE SENSOR)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (WHEEL CYLINDER PRESSURE SENSOR)
a.

Install LSPV gauges to the front wheels (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).


b.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


c.

Check the output value of the wheel cylinder pressure sensor at each hydraulic pressure during electronically controlled brake system control.

Standard Voltage:
for Front Wheel Cylinder LH:
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94

for Front Wheel Cylinder RH:
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

4.READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL STROKE SENSOR ASSEMBLY AND PRESSURE SENSOR COMPARISON)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (BRAKE PEDAL STROKE SENSOR ASSEMBLY AND PRESSURE SENSOR COMPARISON)
a.

Mount a pedal effort gauge and install LSPV gauges to the front and rear wheels (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).


b.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor assembly / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor assembly 2 / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Regulator Pressure Sensor Output Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


c.

Check the output value of the brake pedal stroke sensor assembly as the brake pedal is depressed.

Standard Voltage:
Brake Effort
(N (kgf, lbf))
Stroke Sensor
(V)
Stroke Sensor2
(V)
Regulator Pressure Sensor Output
(V)
Wheel Cylinder Pressure Sensor
(V)
100 (10, 22.5) 1.26 to 1.96 3.04 to 3.74 1.55 to 2.35 1.34 to 2.14
200 (20, 45.0) 1.75 to 2.45 2.55 to 3.25 3.47 to 4.27 2.98 to 3.78


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

5.RECONFIRM DTC

B

C

5.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1246/46 and C1364/61 are not output. A
DTCs C1246/46 and/or C1364/61 are output (for LHD). B
DTCs C1246/46 and/or C1364/61 are output (for RHD). C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY