Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.12–2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light / red (malfunction) remains on:

·

The skid control ECU (brake booster with master cylinder assembly) connector is disconnected from the brake booster with master cylinder assembly.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation has been disabled.


WIRING DIAGRAM

C248090E16
0.604,0.521 1.052,0.667 0.448,0.146 10 false CANH 0.615,1.073 1.052,1.219 0.438,0.146 10 false CANL 4.448,2.729 4.927,2.875 0.479,0.146 10 false CANH 4.469,2.031 4.906,2.177 0.438,0.146 10 false CANL 6.219,2.74 6.625,2.885 0.406,0.146 10 false CA1H 6.219,2.052 6.656,2.198 0.438,0.146 10 false CA1L 1.146,0.542 1.458,0.688 0.313,0.146 10 false G59 1.198,0.313 1.375,0.5 0.177,0.188 10 false 14 1.146,1.083 1.438,1.229 0.292,0.146 10 false G59 1.198,0.854 1.375,1.052 0.177,0.198 10 false 13 4.969,1.938 5.146,2.083 0.177,0.146 10 false 32 4.969,2.625 5.146,2.771 0.177,0.146 10 false 31 6.219,3.833 6.469,3.979 0.25,0.146 10 false IG1 6.219,4.406 6.583,4.552 0.365,0.146 10 false LBL 5.938,4.375 6.167,4.542 0.229,0.167 10 false 36 2.365,3.292 2.573,3.438 0.208,0.146 10 false G1 2.594,3.292 4.458,3.49 1.865,0.198 10 false Combination Meter Assembly 1.99,3.823 3.354,4.063 1.365,0.24 10 false from IG1 NO. 1 Relay 4.354,3.979 5.323,4.188 0.969,0.208 10 false ECU-IG NO. 1 4.979,8.188 7.104,8.573 2.125,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.521,5.656 0.823,5.802 0.302,0.146 10 false PKB 0.448,5.896 0.677,6.115 0.229,0.219 10 false 12 0.083,8.146 1.76,8.49 1.677,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 1.188,7.135 1.385,7.292 0.198,0.156 10 false 3A 1.208,6.927 1.417,7.073 0.208,0.146 10 false 28 3.146,5.146 3.24,5.292 0.094,0.146 10 false 1 1.969,7.031 2.063,7.177 0.094,0.146 10 false 1 1.729,5.146 1.823,5.292 0.094,0.146 10 false 2 1.156,5.865 1.438,6.052 0.281,0.188 10 false A27 1.469,5.844 3.594,6.396 2.125,0.552 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 1.573,7.438 1.854,7.583 0.281,0.146 10 false G24 1.885,7.438 3.25,7.792 1.365,0.354 10 false Parking Brake Switch Assembly 6.219,5.292 6.635,5.438 0.417,0.146 10 false GND 6.219,5.76 6.635,5.906 0.417,0.146 10 false GND2 6.219,6.198 6.635,6.344 0.417,0.146 10 false GND3 6.219,6.656 6.635,6.802 0.417,0.146 10 false GND4 6.219,7.104 6.635,7.25 0.417,0.146 10 false GND5 6.219,7.552 6.635,7.698 0.417,0.146 10 false GND6 4.656,8.198 4.938,8.406 0.281,0.208 10 false A41 1.948,5.146 2.104,5.281 0.156,0.135 10 false + 2.927,5.146 3.083,5.354 0.156,0.208 10 false E 5.938,5.208 6.167,5.396 0.229,0.188 10 false 28 5.938,5.635 6.188,5.844 0.25,0.208 10 false 27 5.969,6.083 6.167,6.25 0.198,0.167 10 false 26 5.938,6.521 6.167,6.74 0.229,0.219 10 false 25 5.938,6.979 6.167,7.177 0.229,0.198 10 false 24 5.938,7.417 6.167,7.635 0.229,0.219 10 false 23 5.938,3.719 6.167,3.885 0.229,0.167 10 false 16 5.938,2.625 6.167,2.802 0.229,0.177 10 false 37 5.958,1.938 6.167,2.104 0.208,0.167 10 false 38 2.146,7.01 2.302,7.146 0.156,0.135 10 false +

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK DTC
a.

Check if ABS, VSC and/or electronically controlled brake system DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK CAN COMMUNICATION SYSTEM

B

2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

4.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (ready) 11 to 15.5 V




OK

5.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
U183564E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.363,1.865 1.102,2.711 false 0.978,2.754 1.335,2.911 0.357,0.158 10 IG1

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
U183556E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 2.279,1.803 2.279,0.999 false 2.381,1.803 2.731,0.666 false 2.17,1.803 1.82,0.666 false 2.031,0.806 2.440,0.963 0.409,0.158 10 GND4 1.554,0.488 1.963,0.645 0.409,0.158 10 GND5 2.493,0.488 2.902,0.645 0.409,0.158 10 GND3 2.476,1.801 3.025,0.982 false 2.815,0.806 3.225,0.963 0.409,0.158 10 GND2 2.08,1.801 1.53,0.982 false 1.251,0.806 1.660,0.963 0.409,0.158 10 GND6 2.648,1.994 2.942,2.761 false 2.776,2.782 3.134,2.940 0.357,0.158 10 GND

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-28 (GND) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-27 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-26 (GND3) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-25 (GND4) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-24 (GND5) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A41-23 (GND6) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

7.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)
a.

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch assembly / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


e.

Using the intelligent tester, check if the switch condition on the intelligent tester changes according to parking brake operation.

OK:

The intelligent tester displays ON or OFF according to parking brake operation.




OK

8.INSPECT COMBINATION METER ASSEMBLY

NG

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY
8.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the power switch off (lock).


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The brake warning light / red (malfunction) turns on or off in accordance with intelligent tester operation.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE COMBINATION METER ASSEMBLY

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
C211519E11
1.75,2 0.823,2.854 false 0.375,0.292 0.542,0.458 0.167,0.167 10 false *a 0.74,2.854 0.865,3.021 0.125,0.167 10 false +

Turn the power switch off (lock).


b.

Disconnect the parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - Body ground Parking brake switch assembly ON
(Switch pin free)
Below 1 Ω
1 (+) - Body ground Parking brake switch assembly OFF
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch Assembly)



OK

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 (PKB) - G24-1 (+) Always Below 1 Ω
3A-28 (PKB) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR