Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1380/64  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop lights come on.

DTC No. INF Code DTC Detection Condition Trouble Area
C1380/64 761 When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is ON, a signal is not input to the STP2 terminal for 2 seconds or more.
·

Stop light control relay (Stop light switch assembly)

·

Stop light control relay (Stop light switch assembly) circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 762 When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is OFF, the signal at the STP terminal is different from the input signal at the STP2 for 5 seconds or more. ↑

WIRING DIAGRAM

C251180E04
1.406,1.083 1.823,1.25 0.417,0.167 10 false STOP 6.125,1.865 6.563,2.021 0.438,0.156 10 false STP0 5.885,2.656 6.083,2.823 0.198,0.167 10 false 33 5.958,1.74 6.146,1.906 0.188,0.167 10 false 3 2.552,0.813 2.677,0.979 0.125,0.167 10 false 7 6.125,0.938 6.552,1.094 0.427,0.156 10 false STP2 1.115,1.948 2.51,2.135 1.396,0.188 10 false from Auxiliary Battery 2.323,3.406 2.656,3.573 0.333,0.167 10 false A32 2.646,3.406 4.573,3.76 1.927,0.354 10 false Stop Light Control Relay (Stop Light Switch Assembly) 4.625,4.906 4.948,5.063 0.323,0.156 10 false A41 4.938,4.906 7.063,5.271 2.125,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.281,2.656 4.406,2.823 0.125,0.167 10 false 1 3.063,4.375 4.365,4.563 1.302,0.188 10 false to Stop Light Circuit 5.958,0.813 6.156,0.979 0.198,0.167 10 false 6 6.125,2.781 6.552,2.938 0.427,0.156 10 false STP 2.552,2.656 2.667,2.823 0.115,0.167 10 false 2 4.281,0.813 4.469,0.979 0.188,0.167 10 false 3 4.281,1.74 4.406,1.906 0.125,0.167 10 false 4 2.729,2.781 3.146,2.948 0.417,0.167 10 false GND 2.729,0.927 2.979,1.094 0.25,0.167 10 false B 4.094,0.927 4.208,1.094 0.115,0.167 10 false L 3.885,1.854 4.25,2.021 0.365,0.167 10 false ACC 3.885,2.781 4.25,2.948 0.365,0.167 10 false OUT

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

When C1249/49 is output together with C1380/64, inspect and repair the trouble areas indicated by C1249/49 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1249/49).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch assembly condition observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY)

NG

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay (Switch) ON/OFF Stop lights come on


b.

Perform the Active Test of the stop light control relay (stop light switch assembly) using the intelligent tester.


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (Stop light switch assembly) output / ON or OFF ON: Relay output on
OFF: Relay output off
-


d.

Check for stop light control relay (stop light switch assembly) operation using the Data List and stop light operation by performing an Active Test.

Result:
Result Proceed to
Data List content and stop light operation are normal. A
Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off. B




A

4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

B

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
U183561E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.662,1.707 1.067,2.778 false 0.809,2.791 1.221,2.948 0.413,0.158 10 STP2

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-6 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A41-6 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1380/64 is not output. A
DTC C1380/64 is output (for LHD). B
DTC C1380/64 is output (for RHD). C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light control relay (stop light switch assembly) (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light control relay (stop light switch assembly) is normal.




OK

7.CHECK HARNESS AND CONNECTOR (STP0 TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP0 TERMINAL)
a.
U183562E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.36,1.707 1.067,2.778 false 0.809,2.791 1.221,2.948 0.413,0.158 10 STP0

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-3 (STP0) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP0 CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U183557E01
0.196,0.187 0.401,0.345 0.205,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.566,2.121 1.084,2.676 false 0.96,2.719 1.318,2.877 0.357,0.158 10 STP

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-33 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V
A41-33 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)