The DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1391/69 | 351 | Either of the following is detected:
1.
Accumulator pressure sensor input does not increase before braking or while the pump motor is operating. 2.
Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating. |
·
Brake fluid leaks ·
Brake actuator (Brake booster with master cylinder assembly) (Malfunctioning internal seal, low gas pressure in accumulator, etc.) |
When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.
Check that the brakes are not dragging.
There are no fluid leaks or dragging.
OK
NG
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1391/69 is output. | A |
| DTC C1391/69 is not output (for LHD). | B |
| DTC C1391/69 is not output (for RHD). | C |
A
B
C
Turn the power switch off (lock).
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
The Active Test can be performed when the following conditions are met.
ABS main relay is on.
Shift lever is in P.
Parking brake is applied.
Vehicle speed is 0 km/h (0 mph).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB* Solenoid (SMC/SRC/SCC) | Switching solenoid valve (SMC/SRC/SCC) | Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
*: Electronically Controlled Brake System
Perform the Active Test of the solenoid using the intelligent tester.
Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.10 to 0.90 V | Reading increases when brake pedal is depressed |
Check that the output value of the wheel cylinder pressure sensor does not increase.
The output value of the wheel cylinder pressure sensor does not increase.
If the output value increases, there may be brake fluid leaks in the brake actuator (brake booster with master cylinder assembly).
| Result | Proceed to |
|---|---|
| The output value of the wheel cylinder pressure sensor increases. | A |
| The output values of the wheel cylinder pressure sensor does not increase (for LHD). | B |
| The output values of the wheel cylinder pressure sensor does not increase (for RHD). | C |
A
B
C
Replace the brake actuator (brake booster with master cylinder assembly) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL for LHD or Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL for RHD).
| Result | Proceed to |
|---|---|
| NEXT (for LHD) | A |
| NEXT (for RHD) | B |
A
B