Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.12–2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1202/68  Master Reservoir Level Malfunction  


DESCRIPTION

When a fluid level drop in the brake master cylinder reservoir assembly is detected, a signal is sent to the skid control ECU.

If the DTC for the fluid level drop is memorized, the warning will be canceled and the DTC will not be stored when the fluid level returns to normal.

DTC No. INF Code DTC Detection Condition Trouble Area
C1202/68 371 An open is detected in the switch signal circuit for 2 seconds or more.
·

Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal open circuit

·

Open in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ - The reservoir level remains low.
·

Low brake fluid level

·

Brake fluid leaks

·

Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal short circuit

·

Short in wire harness

·

Brake disc rotor excessive wear

·

Skid control ECU (Brake booster with master cylinder assembly)



WIRING DIAGRAM

C209586E17
2.54,2.048 4.665,2.592 2.125,0.545 10 Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 4.411,1.217 4.510,1.377 0.099,0.159 10 2 2.2,2.048 2.526,2.207 0.326,0.159 10 A27 2.506,1.217 2.606,1.377 0.099,0.159 10 1 5.553,1.217 5.730,1.377 0.177,0.159 10 36 4.981,2.949 7.077,3.292 2.097,0.343 10 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.806,1.317 6.083,1.476 0.277,0.159 10 LBL 4.674,2.949 4.951,3.108 0.277,0.159 10 A41 4.233,1.217 4.351,1.377 0.118,0.159 10 + 2.678,1.217 2.824,1.377 0.146,0.159 10 E

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

Before releasing the parking brake, chock the wheels for safety.


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

OK:

Brake fluid level is sufficient.


HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (Connection between the brake booster pump assembly, brake master cylinder reservoir assembly and brake booster with master cylinder assembly, and the brake booster with master cylinder assembly and wheel cylinders).

HINT:

If no leaks exist, add and adjust fluid using the intelligent tester (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION).





b.

Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor / Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator


v.

Wait for 30 seconds without depressing the brake pedal.


vi.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.





OK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.
C230719E11
1.948,1.99 2.458,2.76 false 1.521,2 1.021,2.771 false 0.365,0.302 0.594,0.49 0.229,0.188 10 false *a 2.438,2.792 2.615,2.979 0.177,0.188 10 false E 0.896,2.792 1.052,2.979 0.156,0.188 10 false +

Turn the power switch off (lock).


b.

Remove the reservoir filler cap.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 1 (E) Brake fluid level warning switch OFF (Float up) 1.84 to 2.16 kΩ
2 (+) - 1 (E) Brake fluid level warning switch ON (Float down) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-36 (LBL) - A27-2 (+) Always Below 1 Ω
A41-36 (LBL) - Body ground Always 10 kΩ or higher
A27-1 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω




OK

4.INSPECT SKID CONTROL ECU (SWITCH INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SKID CONTROL ECU (SWITCH INPUT)
a.
U183550E02
1.969,2.063 2.406,2.615 false 0.354,0.375 0.594,0.573 0.24,0.198 10 false *a 2.417,2.615 2.594,2.813 0.177,0.198 10 false + 0.521,1.042 0.813,1.219 0.292,0.177 10 false A27

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-2 (+) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

5.CHECK BRAKE DISC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK BRAKE DISC
a.

Turn the power switch off (lock).


b.

Reconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Disconnect the brake pedal stroke sensor assembly connector.


d.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation (See page Brake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION for front, or Brake>BRAKE (REAR)>REAR BRAKE>INSPECTION for rear).





OK

6.RECONFIRM DTC

NG

REPLACE BRAKE DISC

6.RECONFIRM DTC
a.

Reconnect the brake pedal stroke sensor assembly connector.



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1202/68 is not output. A
DTC C1202/68 is output (for LHD). B
DTC C1202/68 is output (for RHD). C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY