Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD) › from 2014.12
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278029 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C249831E01
2.114,2.606 2.286,2.753 0.172,0.147 10 *1 0.413,2.931 0.585,3.078 0.172,0.147 10 *2 1.642,2.686 2.114,2.686 false 3.127,2.96 3.299,3.107 0.172,0.147 10 *3 2.732,3.04 3.127,3.04 false 2.807,3.247 2.979,3.395 0.172,0.147 10 *4 2.395,4.191 2.567,4.338 0.172,0.147 10 *5 2.412,3.327 2.807,3.327 false 1.648,3.292 0.612,3.027 0.612,3.027 1.259,3.463 false 1.714,3.914 2.352,4.27 2.352,4.27 1.51,4.269 false

Install the brake booster with master cylinder assembly with the 4 nuts.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Brake Master Cylinder Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




b.

Install the wire harness clamp to the stud bolt of the brake booster with master cylinder assembly.


c.
C249850

Connect the connector to the brake booster with master cylinder assembly.

Text in Illustration
V100135

Connect the connector
V100136

Lock the lock lever

NOTICE:
·

Make sure that the connector can be connected smoothly. Do not allow foreign matter to enter.

·

Make sure that the connector lock is locked securely.




Hide 3.CONNECT BRAKE LINE

a.

Install the brake tube clamp to the clamp bracket of the brake booster with master cylinder assembly.


b.
U162297E03
1.333,1.698 0.917,1.698 true 1.302,1.573 0.615,1.573 true 1.313,1.427 0.917,1.427 true 1.313,1.281 0.615,1.281 true 1.917,1.219 2.646,1.219 true 0.729,1.594 0.896,1.75 0.167,0.156 10 true *d 0.729,1.333 0.896,1.49 0.167,0.156 10 true *b 0.427,1.49 0.594,1.646 0.167,0.156 10 true *c 0.427,1.188 0.594,1.344 0.167,0.156 10 true *a 2.635,1.115 2.802,1.271 0.167,0.156 10 true *e

Temporarily tighten each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


c.

Using a union nut wrench, fully tighten each brake line.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47101A 5.INSTALL BRAKE PEDAL RETURN SPRING

Hide 47233 6.INSTALL RESERVOIR BRACKET

a.

Install the reservoir bracket with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 44572 7.CONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C249845E01
1.795,0.349 2.064,0.507 0.269,0.159 10 30° 1.795,0.841 2.064,0.999 0.269,0.159 10 30°

Connect the No. 2 brake actuator hose to the No. 1 brake actuator tube with the clip.

Text in Illustration
V100136

Front of Vehicle

NOTICE:
·

When connecting the No. 2 brake actuator hose, face the identification mark to the front of the vehicle.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47234L 8.CONNECT NO. 1 RESERVOIR HOSE

a.
C249843E01
1.563,0.174 1.825,0.330 0.262,0.156 10 90° 2.451,0.174 2.713,0.330 0.262,0.156 10 90°

Connect the No. 1 reservoir hose to the brake booster with master cylinder assembly with the clip.

Text in Illustration
V100136

Up

NOTICE:
·

Make sure that the identification mark on the No. 1 reservoir hose is positioned within 30° of the brake booster with master cylinder assembly rib.

·

When connecting the No. 1 reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47235G 9.CONNECT NO. 2 RESERVOIR HOSE

a.
C249841E01
1.528,0.197 1.786,0.358 0.258,0.161 10 90° 2.497,0.197 2.754,0.358 0.258,0.161 10 90°

Connect the No. 2 reservoir hose to the brake booster with master cylinder assembly with the clip.

Text in Illustration
V100136

Up

NOTICE:
·

Make sure that the identification mark on the No. 2 reservoir hose is positioned within 30° of the brake booster with master cylinder assembly rib.

·

When connecting the No. 2 reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 44551 10.BLEED NO. 1 BRAKE ACTUATOR TUBE

a.

Add brake fluid into the brake master cylinder reservoir assembly.


b.
C249861E02
2.385,1.281 2.385,1.083 2.385,1.083 2.625,1.083 false 2.635,1.01 2.854,1.188 0.219,0.177 10 true *1

Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the No. 1 brake actuator tube.

Text in Illustration
*1 No. 1 Brake Actuator Tube

NOTICE:
·

Do not damage the hoses or tubes.

·

Do not spill the brake fluid.

·

Continue this procedure until only a minor amount of air remains in the brake actuator tube.




Hide 47220D 11.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.

Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12.FILL RESERVOIR WITH BRAKE FLUID

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 15.INSPECT AND ADJUST BRAKE PEDAL

Hide 16. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

Hide 55701J 17.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
C249838E02
2.583,0.427 2.792,0.635 0.208,0.208 10 true (1) 0.99,0.51 1.188,0.708 0.198,0.198 10 true (2)

Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

Torque:
Bolt : 7.0 N*m (71 kgf*cm, 62 in.*lbf)
Nut : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.



b.

Engage the 3 clamps to install the wire harness.


Hide 55815E 18.INSTALL FRONT NO. 1 VENTILATOR SEAL

a.

Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.


Hide 55735B 19.INSTALL FRONT AIR SHUTTER SEAL

a.

Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.


Hide 55722C 20.INSTALL INNER COWL TOP TO COWL BRACE

a.
C249834E02
2.729,0.188 2.927,0.365 0.198,0.177 10 true (1) 2.354,1.177 2.552,1.354 0.198,0.177 10 true (2) 1.719,0.177 1.917,0.354 0.198,0.177 10 true (3)

Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

Tighten the 3 bolts in the order shown in the illustration.



Hide 21.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY