Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › from 2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch.

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>PRECAUTION).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the hybrid control system. If the steering is locked for any reason, open and close a door with the power switch off, and then unlock the steering by pressing the power switch. This prevents the hybrid control system from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal

·

Starter Request Signal


Entry&Start
·

S Code Check

·

L Code Check

·

Engine Start Request


-


PROCEDURE

1.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (HYBRID SYSTEM PERMISSION CONDITIONS WERE NOT SATISFIED)

NG

2.CHECK AUXILIARY BATTERY
2.CHECK AUXILIARY BATTERY
a.

Measure the auxiliary battery voltage with the power switch off.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

·

If the auxiliary battery voltage is less than 11 V, charge or replace it.





NEXT

3.CHECK FOR DTC (ALL)
3.CHECK FOR DTC (ALL)
a.

Using the intelligent tester, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.




OK

4.CHECK WAVE ENVIRONMENT

NG

GO TO DTC CHART

4.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver (RF band).




NEXT

5.CHECK POWER SWITCH CONDITION
5.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.

Result:
Result Proceed to
Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) and on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D




A

6.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)

B

C

D

6.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.

·

The hybrid control system cannot be started when the steering unlock signal is off.



OK:

The item in the Data List indicates "ON" (the steering is unlocked).




OK

7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)

NG

7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.



OK:

The item in the Data List changes when the brake pedal is depressed and released.




OK

8.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)

NG

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
8.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check w/o ID Code Box (Immobiliser Code ECU):
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG
w/ ID Code Box (Immobiliser Code ECU):
Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)/OK or NG
OK: Verification result normal
NG: Verification result abnormal

When NG is displayed:


·

L code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).

·

Steering wheel cannot be locked.

·

Steering wheel cannot be unlocked (the hybrid system cannot be started).



OK:

The Data List item changes to "OK" when the electrical key transmitter sub-assembly is inside the vehicle.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.





OK

9.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

NG

13.CHECK STEERING LOCK ACTUATOR ASSEMBLY
9.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Start Condition Status of hybrid control system start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/ OK or NG OK: Hybrid control system start permitted
NG: Hybrid control system start prohibited
·

When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and hybrid control system starting possible.

·

The hybrid control system cannot be started when NG is displayed.



NOTICE:

Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the power switch.


OK:

The display changes in response to the operation of the power switch.


Result:
Result Proceed to
NG A
OK B




A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

15.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.
U183738E02
1.333,1.292 1.042,1.75 false 1.719,1.292 2,1.771 false 0.219,0.125 0.573,0.417 0.354,0.292 10 false *a 1.594,0.208 1.948,0.5 0.354,0.292 10 false A65 0.958,1.75 1.125,1.938 0.167,0.188 10 false B 1.854,1.771 2.219,1.958 0.365,0.188 10 false GND

Disconnect the A65 stop light switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-1 (B) - A65-3 (GND) Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A65-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

11.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
U183743E01
0.245,0.128 0.447,0.302 0.202,0.174 10 *a 1.583,0.196 1.943,0.370 0.360,0.174 10 A65 2.583,1.623 2.953,1.798 0.370,0.174 10 OUT 2.051,1.625 2.475,1.799 0.424,0.174 10 GND 2.59,1.617 1.954,1.274 false 1.758,1.286 2.216,1.626 false

Reconnect the A65 stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-2 (OUT) - A65-3 (GND) Power switch off, brake pedal not depressed Below 1 V
A65-2 (OUT) - A65-3 (GND) Power switch off, brake pedal depressed 11 to 14 V


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - STOP LIGHT SWITCH ASSEMBLY)

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK STEERING LOCK ACTUATOR ASSEMBLY
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY).


b.

Perform the registration procedures (Refer to the Service Bulletin).



NEXT

14.CHECK HYBRID CONTROL SYSTEM (READY ON)
14.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

15.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)/OK or NG OK: Verification result normal
NG: Verification result abnormal

When NG is displayed:


·

registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

Steering cannot be locked.

·

Steering cannot be unlocked (the hybrid system cannot be started).



OK:

The Data List item changes to "OK" when the electrical key transmitter sub-assembly is inside the vehicle.


HINT:

Reasons for verification failure:

·

The ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.





OK

16.CHECK ENGINE IMMOBILISER SYSTEM

NG

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
16.CHECK ENGINE IMMOBILISER SYSTEM
a.
U183363E02
1.802,1.042 1.51,1.813 false 2.573,1.167 2.302,1.792 false 2.625,1.167 2.896,1.802 false 2.458,0.302 2.74,0.438 0.281,0.135 10 false G81 1.906,0.302 2.188,0.438 0.281,0.135 10 false G80 0.031,0.031 0.188,0.167 0.156,0.135 10 false *a 2.146,1.802 2.427,1.938 0.281,0.135 10 false IMO 2.833,1.802 3.052,1.938 0.219,0.135 10 false IMI 1.406,1.802 1.594,1.938 0.188,0.135 10 false E1

Check the waveform according to the condition(s) in the table below.

Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

i.

Waveform 1

B443942E01
0.698,1.26 1.156,1.458 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G81-23 (IMO) - G80-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2

B443943E01
0.729,1.25 1.188,1.448 0.458,0.198 10 false GND 3.115,1.354 3.573,1.552 0.458,0.198 10 false *a 3.313,1.354 3.771,1.552 0.458,0.198 10 false *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Measurement Condition
Item Content
Tester Connection G81-22 (IMI) - G80-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected

OK:

The waveform is displayed as shown in illustration.





OK

17.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

NG

20.CHECK AND REPLACE HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ID CODE BOX (IMMOBILISER CODE ECU))
17.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status/ON or OFF ON: With the shift lever in P and brake pedal depressed, the power switch is pressed and held
OFF: After approx. 1 sec. has elapsed, the power switch is released
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain amount of time.



NOTICE:

Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the power switch.


OK:

The display changes in response to the operation of the power switch.




OK

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one (Refer to the Service Bulletin).


b.

Perform the registration procedures (Refer to the Service Bulletin).



NEXT

19.CHECK HYBRID CONTROL SYSTEM (READY ON)
19.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

20.CHECK AND REPLACE HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ID CODE BOX (IMMOBILISER CODE ECU))
a.

Disconnect the G81 connector from the hybrid vehicle control ECU.


b.

Disconnect the G49 connector from the ID code box (immobiliser code ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-23 (IMO) - G49-3 (EFII) Always Below 1 Ω
G81-22 (IMI) - G49-4 (EFIO) Always Below 1 Ω




OK

21.REPLACE HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.REPLACE HYBRID VEHICLE CONTROL ECU
a.

Replace the hybrid vehicle control ECU with a new one (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL).



NEXT

22.CHECK HYBRID CONTROL SYSTEM (READY ON)
22.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (HYBRID VEHICLE CONTROL ECU WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)