Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
89860C
1.INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.
| *a | Incorrect | *b | Correct |
Insert the pin (stopper) into the body hole and install the side No. 2 airbag sensor assembly to the vehicle body with the bolt.
If the side No. 2 airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the side No. 2 airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the pin (stopper) is securely inserted into the body hole.
Tighten the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.
Connect the connector to the side No. 2 airbag sensor assembly.
When connecting any airbag connector, take care not to damage the airbag wire harness.
Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).
| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connection is Completed | - | - |
When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.
Check that there is no looseness in the installation parts of the side No. 2 airbag sensor assembly.
64740C
2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY
81330
3.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)
73370
4.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
64716D
5.INSTALL REAR DECK TRIM COVER
64330D
6.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
64997
7.INSTALL DECK FLOOR BOX LH
64995
8.INSTALL DECK FLOOR BOX RH
Use the same procedure for the RH side and LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).
58410B
9.INSTALL DECK BOARD ASSEMBLY
62332A
10.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
67918A
11.INSTALL REAR DOOR SCUFF PLATE
12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
13.INSTALL REAR SEATBACK ASSEMBLY
for Separate Type Seatback LH Side: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>INSTALLATION)
for Separate Type Seatback RH Side: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>INSTALLATION)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>INSTALLATION)
14.INSTALL REAR SEAT CUSHION ASSEMBLY
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>INSTALLATION)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>INSTALLATION)
58167H
15.INSTALL FRONT CENTER FLOOR COVER
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>INSTALLATION)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>INSTALLATION)
58166B
16.INSTALL FRONT FLOOR COVER LH
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>INSTALLATION)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>INSTALLATION)
58165F
17.INSTALL FRONT FLOOR COVER RH
for Separate Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>INSTALLATION)
for Bench Type Seatback: (See page Vehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Bench Type Seatback)>INSTALLATION)
71960B
18.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for LH Side)
71940A
19.INSTALL REAR SEAT HEADREST ASSEMBLY
20. PERFORM DIAGNOSTIC SYSTEM CHECK
21.INSPECT SRS WARNING LIGHT