The crank position sensor system consists of a crank angle sensor plate and a pickup coil.
The crank angle sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crank angle sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0335 | Either of the following conditions is met (1 trip detection logic):
·
No crank position sensor signal to ECM while engine running. ·
Missing crank position sensor signal despite cam position sensor signal inputs normal after engine cranked. |
·
Open or short in crank position sensor circuit ·
Crank position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
G2+ stands for the cam position sensor signal, and NE+ stands for the crank position sensor signal.
Grounding failure of the shielded wire may cause noise in the waveforms.
| ECM Terminal Name | CH1: Between G2+ and G2-
CH2: Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
If there is no signal from the crank position sensor despite the crankshaft rotating, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Crank position sensor |
| Required Sensors/Components (Related) | Cam position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn thepower switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine.
Idle the engine for 20 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0335.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.
After performing the inspection procedure for the crank position sensor, if DTC P0335 is output again, check the following items related to the cam position sensor.
Installation condition of the cam position sensor
Installation condition of the camshaft
Connection of the cam position sensor connector
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crank position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crank position sensor output voltage is insufficient.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
Read the values displayed on the GTS while the engine is running.
Correct values are displayed.
To check the engine speed change, display the graph on the GTS.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crank position sensor circuit.
OK
NG
Inspect the crank position sensor.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSPECTION
OK
NG
Disconnect the crank position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C29-1 - C10-78 (NE+) | Always | Below 1 Ω |
| C29-2 - C10-110 (NE-) | Always | Below 1 Ω |
| C29-1 or C10-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C29-2 or C10-110 (NE-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the crank position sensor installation.
Crank position sensor is installed correctly.
OK
NG
Inspect the teeth of the crank angle sensor plate.
Crank angle sensor plate does not have any cracks or deformation.
OK
NG