Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › 2017.06–2018.08
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P050A  Cold Start Idle Air Control System Performance  


MONITOR DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC will be stored after the engine idles for 13 seconds (2 trip detection logic).

The DTC is designed to monitor the idle air control at cold start. When the engine is started at an engine coolant temperature of less than 50°C (122°F), the ECM measures the accumulated mass air flow during engine idling. If the accumulated mass air flow does not reach the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

The electronic throttle control system controls the idle speed. The electronic throttle control system operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:

The idle speed control learned values are cleared by performing a learned value reset. Idle speed control learning needs to be performed before this DTC can be stored. To perform idle speed control learning, the engine must be warmed up by allowing it to idle for 5 minutes. For idle speed control learning to be successful, when the engine is started to warm it up, there must be at least 10 seconds of idling with the coolant temperature less than 50°C (122°F) before allowing it to continue running for the 5 minutes learning period.


A234891E11
0.086,0.025 1.888,0.209 1.802,0.184 10 P050A Detection Logic: 1.4,2.863 2.260,3.074 0.860,0.211 10 Engine Start 4.755,1.05 6.363,1.207 1.607,0.157 10 Pass Condition Detected 4.755,2.072 5.547,2.253 0.791,0.181 10 Malfunction 2.111,2.544 2.267,2.725 0.156,0.181 10 0 2.937,2.915 3.632,3.077 0.695,0.162 10 3 seconds 4.604,2.915 5.368,3.078 0.765,0.163 10 13 seconds 2.577,2.657 2.224,2.912 false 4.888,2.577 5.214,2.758 0.326,0.181 10 Time 4.755,1.572 5.446,1.727 0.691,0.156 10 Threshold 1.342,0.764 2.247,1.100 0.906,0.336 10 Accumulated Mass Air Flow 2.206,3.328 4.972,3.493 2.767,0.165 10 Engine Coolant Temperature: -10 to 50°C

DTC No. DTC Detection Condition Trouble Area
P050A Insufficient mass air flow after a cold start (2 trip detection logic).
·

Throttle body with motor assembly

·

Mass air flow meter sub-assembly

·

PCV system

·

Air cleaner filter element

·

Intake system

·

VVT system

·

EGR valve assembly

·

Wire harness or connector

·

ECM



MONITOR STRATEGY

Required Sensors/Components (Main) Throttle body with motor assembly
Required Sensors/Components (Related) Mass air flow meter sub-assembly
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL MALFUNCTION THRESHOLDS

Accumulated mass air flow Less than 20 g (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

6.

Start the engine and warm it up for 5 minutes or more.

7.

Stop the engine.

8.

Leave the vehicle outside overnight.

9.

Turn the power switch on (IG) and turn the GTS on [A].

10.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

11.

Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).

12.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

13.

Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.

14.

Idle the engine for 1 minute or more [B].

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P050A.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [C] again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P050A is output A
DTC P050A and other DTCs are output B

HINT:

If any DTCs other than P050A are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (FUEL TRIM)

B

2.READ VALUE USING GTS (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter sub-assembly.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Gas AF Control / Short FT B1S1 and Long FT B1S1.


g.

Read the values displayed on the GTS at engine idle.


h.

Add together the Short FT B1S1 and Long FT B1S1 values to obtain the total fuel trim.

Standard:

Total of Short FT B1S1 and Long FT B1S1 values is between -20% and 20%.




OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)

NG

7.CHECK PCV SYSTEM
3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)
a.

Check that there are no deposits around the throttle valve and throttle valve condition.

OK:

No deposits around the throttle valve and throttle valve moves smoothly.




OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

6.REPAIR OR REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

5.INSPECT EGR VALVE ASSEMBLY

B

20.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
5.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

20.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NG

17.REPLACE EGR VALVE ASSEMBLY
6.REPAIR OR REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Repair or replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL

HINT:

Perform "Inspection After Repair" after repairing or replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
7.CHECK PCV SYSTEM
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>PCV VALVE>COMPONENTS

OK:

PCV valve and hose are connected correctly and are not damaged.




OK

8.CHECK INTAKE SYSTEM

NG

14.REPAIR OR REPLACE PCV HOSE
8.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from the intake system.




OK

9.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

15.REPAIR OR REPLACE INTAKE SYSTEM
9.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

OK:

The air cleaner filter element is not excessively contaminated with dirt or oil.




OK

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
10.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

11.INSPECT EGR VALVE ASSEMBLY

B

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
11.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

12.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)

NG

17.REPLACE EGR VALVE ASSEMBLY
12.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
a.

Operate the VVT system through the Active test, and check if the VVT system is operating normally.

i.

Perform the Active Test, referring to DTC P0011 Inspection Procedure.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0011




OK

13.READ VALUE USING GTS (MAF)

NG

18.CHECK AND REPAIR VVT SYSTEM
13.READ VALUE USING GTS (MAF)

OK

20.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NG

21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
14.REPAIR OR REPLACE PCV HOSE
a.

Repair or replace the PCV valve or hose.



NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
15.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the intake system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
16.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner filter element sub-assembly.



NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
17.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
18.CHECK AND REPAIR VVT SYSTEM
a.

Check and repair the VVT system.

HINT:

Refer to DTC P0011 Inspection Procedure.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0011




NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.


i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


k.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


l.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


n.

Input the DTC: P050A.


o.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P050A is output)
B



A

END

B

21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
20.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.


i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


k.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


l.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


n.

Input the DTC: P050A.


o.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P050A is output)
B



A

B

21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
21.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.




NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
22.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.


i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


k.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


l.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


n.

Input the DTC: P050A.


o.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(DTC P050A is output)
A
NORMAL
(DTCs are not output)
B



A

23.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

END

23.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

24.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in step 13 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





NEXT

25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.


i.

Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).


j.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


k.

Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.


l.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


n.

Input the DTC: P050A.


o.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P050A is output)
B



A

END

B