Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL INJECTOR › from 2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0277953 FUEL INJECTOR A

1NZ-FXE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 25680 5.REMOVE EGR VALVE WITH COOLER ASSEMBLY

Hide 47220D 6.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

Hide 11201 10.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23841B 11.REMOVE EFI FUEL PIPE CLAMP

a.
A264997

Remove the EFI fuel pipe clamp.


Hide 23901 12.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
U159101E03
2.167,3.344 2.708,2.792 2.708,2.792 2.823,2.792 false 1.906,3.146 1.5,2.74 1.5,2.74 1.396,2.74 false 0.51,3.74 0.51,4.01 false 1.573,3.677 1.573,4.115 1.573,4.115 1.083,4.115 false 1.406,3.677 1.406,4.115 false 3.229,3.646 3.229,4.104 3.229,4.104 2.344,4.104 false 2.5,3.646 2.5,4.104 false 2.844,2.688 3.021,2.875 0.177,0.188 10 false *1 2.167,4.021 2.344,4.208 0.177,0.188 10 false *5 0.875,3.99 1.052,4.177 0.177,0.188 10 false *4 0.427,4.052 0.604,4.24 0.177,0.188 10 false *3 1.198,2.646 1.375,2.833 0.177,0.188 10 false *2

Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel delivery pipe.

Text in Illustration
*1 Fuel delivery pipe
*2 Fuel Tube Connector
*3 Nylon Tube
*4 O-ring
*5 Retainer
V100135

Pinch
V100136

Pull

NOTICE:
·

Check for foreign matter on the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel delivery pipe.

·

Do not use any tools to separate the fuel tube connector and fuel delivery.

·

Do not forcibly bend, kink or twist the nylon tube.

·

Keep the fuel tube connector and fuel delivery pipe free from foreign matter.

·

If the fuel tube connector and fuel delivery pipe are stuck, push and pull to release them.

·

Put the fuel tube connector and fuel delivery pipe in plastic bags to prevent damage and contamination.




Hide 23814B 13.REMOVE FUEL DELIVERY PIPE

a.
A264999

Remove the bolt.


b.
A265000

Disengage the clamp to disconnect the wire harness.


c.

Remove the 2 bolts and the fuel delivery pipe with the 4 fuel injectors.

NOTICE:

Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



Hide 23891 14.REMOVE FUEL DELIVERY SPACER

a.
A265001

Remove the 2 fuel delivery spacers from the cylinder head.


Hide 23291 15.REMOVE INJECTOR VIBRATION INSULATOR

a.
A268449

Remove the 4 injector vibration insulators from the cylinder head.


Hide 23250 16.REMOVE FUEL INJECTOR ASSEMBLY

a.
U158998

Pull the 4 fuel injector assemblies out of the fuel delivery pipe.

Text in Illustration
V100135

Pull


b.

Remove the O-ring from each fuel injector.


c.

For reinstallation, attach a tag or label to each injector shaft.

NOTICE:

Prevent entry of foreign matter by covering the fuel injectors with plastic bags.