Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9C-123  Hybrid Battery Temperature Sensor "A" Range / Performance  P0AC6-123  Hybrid Battery Temperature Sensor "B" Range / Performance  P0ACB-123  Hybrid Battery Temperature Sensor "C" Range / Performance  P0AE9-123  Hybrid Battery Temperature Sensor "D" Range / Performance  P0BC3-123  Hybrid Battery Temperature Sensor "E" Range / Performance  P0C34-123  Hybrid Battery Temperature Sensor "F" Range / Performance  P3065-123  Hybrid Battery Temperature Sensor Range/Performance Stuck "A"  P306A-123  Hybrid Battery Temperature Sensor Range / Performance Stuck "B"  


DESCRIPTION

The battery temperature sensors are provided at 3 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery smart unit uses the battery temperature sensors to detect the HV battery temperature, and sends the detected value to the power management control ECU. Based on the results of this detection, the power management control ECU controls the blower fan. (The blower fan starts when HV battery temperature rises above a predetermined level.)

Temperature Sensor Identification Cross Reference Table:
DTC Title Sensor Battery Temperature Sensor GTS Display
A 0 1
B 1 2
C 2 3


HINT:

For example, sensor A in the DTC title is battery temperature sensor (No. 0). This sensor is displayed as Temp of Batt TB1 in the Data List.


A171806E02
1.824,0.012 2.564,0.170 0.740,0.157 10 Reference: 2.171,0.354 2.431,0.503 0.260,0.149 10 250 2.171,0.673 2.431,0.822 0.260,0.149 10 200 2.171,0.981 2.431,1.129 0.260,0.149 10 150 2.173,1.276 2.433,1.425 0.260,0.149 10 100 2.25,1.579 2.433,1.728 0.184,0.149 10 50 2.331,1.901 2.434,2.050 0.104,0.149 10 0 3.273,2.255 3.376,2.404 0.104,0.149 10 0 2.577,2.252 2.804,2.421 0.227,0.169 10 -40 2.921,2.252 3.148,2.421 0.227,0.169 10 -20 3.522,2.252 3.696,2.421 0.174,0.169 10 20 3.815,2.252 3.989,2.421 0.174,0.169 10 40 4.094,2.252 4.268,2.421 0.174,0.169 10 60 4.401,2.252 4.576,2.421 0.174,0.169 10 80 4.644,2.252 4.901,2.421 0.257,0.169 10 100 3.176,2.457 3.443,2.606 0.268,0.149 10 (32) 2.53,2.451 2.862,2.620 0.332,0.169 10 (-40) 2.908,2.453 3.170,2.622 0.262,0.169 10 (-4) 3.46,2.453 3.727,2.622 0.267,0.169 10 (68) 3.709,2.453 4.075,2.622 0.366,0.169 10 (104) 4.028,2.453 4.372,2.622 0.344,0.169 10 (140) 4.352,2.453 4.702,2.622 0.350,0.169 10 (176) 4.676,2.453 5.021,2.622 0.346,0.169 10 (212) 5.096,2.242 5.370,2.440 0.274,0.198 10 (°C) 5.096,2.445 5.427,2.643 0.331,0.198 10 (°F) 1.82,0.379 2.115,0.577 0.295,0.198 10 (kΩ) 1.403,0.568 2.135,0.752 0.731,0.184 10 Resistance 5.462,2.235 6.800,2.423 1.339,0.188 10 Battery Temperature 2.6,0.008 5.691,0.187 3.091,0.179 10 Battery Temperature Sensor Characteristic Graph


DTC No. INF Code DTC Detection Condition Trouble Area
P0A9C
P0AC6
P0ACB
P0AE9
P0BC3
P0C34
P3065
P306A
123 When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
·

HV battery

·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A255045E03
5.281,4.323 5.698,4.521 0.417,0.198 10 false TB4 5.281,3.927 5.698,4.125 0.417,0.198 10 false GB3 5.281,5.313 5.698,5.51 0.417,0.198 10 false TB5 5.281,4.917 5.698,5.115 0.417,0.198 10 false GB4 5.281,7.281 5.698,7.479 0.417,0.198 10 false TC1 5.281,5.896 5.698,6.094 0.417,0.198 10 false GB5 5.281,7.896 5.688,8.083 0.406,0.188 10 false GC1 4.802,8.323 5.063,8.521 0.26,0.198 10 false z24 5.01,1.229 5.219,1.406 0.208,0.177 10 false 14 5.083,0.844 5.219,1.021 0.135,0.177 10 false 1 5.01,0.25 5.219,0.427 0.208,0.177 10 false 13 1.99,8.323 2.729,8.583 0.74,0.26 10 false HV Battery 1.573,0.573 3.51,0.885 1.938,0.313 10 false Battery Temperature Sensor 0 1.573,1.552 3.51,1.865 1.938,0.313 10 false Battery Temperature Sensor 1 1.573,2.542 3.51,2.854 1.938,0.313 10 false Battery Temperature Sensor 2 1.583,6.5 3.542,6.771 1.958,0.271 10 false Inlet Air Temperature Sensor 0 5.104,8.323 6.281,8.688 1.177,0.365 10 false Battery Smart Unit 1.573,3.531 3.51,3.844 1.938,0.313 10 false Battery Temperature Sensor 3 1.573,4.521 3.51,4.833 1.938,0.313 10 false Battery Temperature Sensor 4 1.573,5.51 3.51,5.823 1.938,0.313 10 false Battery Temperature Sensor 5 1.583,7.49 3.542,7.76 1.958,0.271 10 false Inlet Air Temperature Sensor 1 5.281,6.896 5.688,7.083 0.406,0.188 10 false GC0 5.281,6.302 5.698,6.5 0.417,0.198 10 false TC0 5.281,3.344 5.698,3.542 0.417,0.198 10 false TB3 5.281,2.948 5.698,3.146 0.417,0.198 10 false GB2 5.281,2.354 5.698,2.552 0.417,0.198 10 false TB2 5.281,1.958 5.698,2.156 0.417,0.198 10 false GB1 5.281,1.344 5.698,1.542 0.417,0.198 10 false TB1 5.281,0.979 5.698,1.177 0.417,0.198 10 false GB0 5.281,0.365 5.698,0.563 0.417,0.198 10 false TB0 5,2.24 5.208,2.417 0.208,0.177 10 false 15 5.073,1.844 5.208,2.021 0.135,0.177 10 false 2 5,3.208 5.208,3.385 0.208,0.177 10 false 16 5.073,2.823 5.208,3 0.135,0.177 10 false 3 4.99,4.219 5.198,4.396 0.208,0.177 10 false 17 5.052,3.813 5.188,3.99 0.135,0.177 10 false 4 5.01,5.208 5.219,5.385 0.208,0.177 10 false 18 5.073,4.813 5.208,4.99 0.135,0.177 10 false 5 5,6.188 5.208,6.365 0.208,0.177 10 false 21 5.063,5.792 5.198,5.969 0.135,0.177 10 false 6 5,7.188 5.208,7.365 0.208,0.177 10 false 22 5.063,6.781 5.198,6.958 0.135,0.177 10 false 9 5.01,7.76 5.219,7.938 0.208,0.177 10 false 10

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)

A

3.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

B

3.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
U190664E02
2.125,0.865 2.396,1.021 0.271,0.156 10 false z24

Disconnect the z24 battery smart unit connector.


d.
U190651E02
2.344,2.26 2.625,2.229 true 2.229,2.24 2.552,1.896 true 2.125,2.24 2.208,1.969 true 2,2.24 1.969,1.75 true 1.896,2.24 1.583,1.74 true 1.792,2.24 1.25,1.75 true 1.479,2.229 0.896,1.781 true 1.385,2.24 0.854,1.958 true 1.479,2.396 0.948,2.781 true 1.375,2.385 0.781,2.615 true 1.896,2.396 1.458,2.906 true 1.781,2.396 1.177,2.885 true 2.01,2.396 2.156,2.917 true 2.125,2.396 2.438,2.875 true 2.229,2.396 2.542,2.708 true 2.344,2.385 2.656,2.552 true 0.677,2.729 1,2.917 0.323,0.188 10 false TC0 0.521,2.552 0.844,2.74 0.323,0.188 10 false TC1 0.583,1.677 0.938,1.865 0.354,0.188 10 false GC0 0.552,1.875 0.906,2.063 0.354,0.188 10 false GC1 0.198,0.094 0.365,0.25 0.167,0.156 10 false *a 2.375,2.885 2.677,3.073 0.302,0.188 10 false TB2 2.031,2.948 2.333,3.135 0.302,0.188 10 false TB3 1.281,2.917 1.583,3.104 0.302,0.188 10 false TB4 0.958,2.896 1.26,3.083 0.302,0.188 10 false TB5 2.552,2.698 2.854,2.885 0.302,0.188 10 false TB1 2.677,2.49 3.031,2.677 0.354,0.188 10 false TB0 2.656,2.135 2.979,2.323 0.323,0.188 10 false GB0 2.583,1.781 2.885,1.969 0.302,0.188 10 false GB1 2.042,1.76 2.344,1.948 0.302,0.188 10 false GB2 1.771,1.552 2.073,1.74 0.302,0.188 10 false GB3 1.385,1.583 1.688,1.771 0.302,0.188 10 false GB4 0.99,1.594 1.292,1.781 0.302,0.188 10 false GB5 0.698,2.302 0.938,2.49 0.24,0.188 10 false z24

Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 5).

Tester Connection
Tester Connection Battery Temperature Sensor No.
z24-13 (TB0) - z24-1 (GB0) 0
z24-14 (TB1) - z24-2 (GB1) 1
z24-15 (TB2) - z24-3 (GB2) 2
z24-16 (TB3) - z24-4 (GB3) 3
z24-17 (TB4) - z24-5 (GB4) 4
z24-18 (TB5) - z24-6 (GB5) 5

Standard Resistance:
Thermistor Temperature Condition Specified Condition
0 °C (32 °F) Power switch off 26.7 to 27.8 kΩ
25 °C (77 °F) Power switch off 9.9 to 10.1 kΩ
40 °C (104 °F) Power switch off 5.73 to 5.92 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Standard Resistance
z24-13 (TB0) - Body ground and other terminals Power switch off 10 kΩ or more
z24-1 (GB0) - Body ground and other terminals Power switch off 10 kΩ or more
z24-14 (TB1) - Body ground and other terminals Power switch off 10 kΩ or more
z24-2 (GB1) - Body ground and other terminals Power switch off 10 kΩ or more
z24-15 (TB2) - Body ground and other terminals Power switch off 10 kΩ or more
z24-3 (GB2) - Body ground and other terminals Power switch off 10 kΩ or more
z24-16 (TB3) - Body ground and other terminals Power switch off 10 kΩ or more
z24-4 (GB3) - Body ground and other terminals Power switch off 10 kΩ or more
z24-17 (TB4) - Body ground and other terminals Power switch off 10 kΩ or more
z24-5 (GB4) - Body ground and other terminals Power switch off 10 kΩ or more
z24-18 (TB5) - Body ground and other terminals Power switch off 10 kΩ or more
z24-6 (GB5) - Body ground and other terminals Power switch off 10 kΩ or more
z24-21 (TC0) - Body ground and other terminals Power switch off 10 kΩ or more
z24-9 (GC0) - Body ground and other terminals Power switch off 10 kΩ or more
z24-22 (TC1) - Body ground and other terminals Power switch off 10 kΩ or more
z24-10 (GC1) - Body ground and other terminals Power switch off 10 kΩ or more



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z24-13 (TB0) - Body ground Power switch on (IG) 1 V or less
z24-1 (GB0) - Body ground Power switch on (IG) 1 V or less
z24-14 (TB1) - Body ground Power switch on (IG) 1 V or less
z24-2 (GB1) - Body ground Power switch on (IG) 1 V or less
z24-15 (TB2) - Body ground Power switch on (IG) 1 V or less
z24-3 (GB2) - Body ground Power switch on (IG) 1 V or less
z24-16 (TB3) - Body ground Power switch on (IG) 1 V or less
z24-4 (GB3) - Body ground Power switch on (IG) 1 V or less
z24-17 (TB4) - Body ground Power switch on (IG) 1 V or less
z24-5 (GB4) - Body ground Power switch on (IG) 1 V or less
z24-18 (TB5) - Body ground Power switch on (IG) 1 V or less
z24-6 (GB5) - Body ground Power switch on (IG) 1 V or less
z24-21 (TC0) - Body ground Power switch on (IG) 1 V or less
z24-9 (GC0) - Body ground Power switch on (IG) 1 V or less
z24-22 (TC1) - Body ground Power switch on (IG) 1 V or less
z24-10 (GC1) - Body ground Power switch on (IG) 1 V or less


HINT:

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the z24 battery smart unit connector.


l.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG