Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AAE-123  Hybrid Battery Pack Air Temperature Sensor "A" Circuit Low  P0AAF-123  Hybrid Battery Pack Air Temperature Sensor "A" Circuit High  P0AB3-123  Hybrid Battery Pack Air Temperature Sensor "B" Circuit Low  P0AB4-123  Hybrid Battery Pack Air Temperature Sensor "B" Circuit High  P3103-123  EV Battery Pack Air Temperature Sensor "A" / "B" Correlation  


DESCRIPTION

The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensor (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123). The battery smart unit uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.


DTC No. INF Code DTC Detection Condition Trouble Area
P0AAE 123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open circuit) or is higher than a predetermined limit (short circuit)(1 trip detection).
·

HV BATTERY

·

Battery smart unit

·

Wire harness or connector

·

Hybrid battery junction block assembly


P0AAF
P0AB3
P0AB4
P3103 The intake air temperature sensor value exceeds the upper or lower thresholds.

HINT:

After confirming that a DTC is output, use the GTS to check "Inhaling Air Temp" in the HV ECU data list.


Displayed Temperature Malfunction
-45 °C (-49 °F) or less Open or +B short circuit
95 °C (203 °F) or more GND short

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).

Refer to the wiring diagram for DTC P0ABF-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

DTC P3103-123 may be stored if a heat generating object is placed near the HV battery in the console box assembly. In this case, check for DTCs after removing the object.

·

If a short to +B occurs in the battery temperature sensor, battery current sensor or intake air temperature sensor, the following DTCs may be output simultaneously.



DTC No. Relevant Diagnosis
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AEB-123 Hybrid Battery Temperature Sensor "D" Circuit High
P0BC5-123 Hybrid Battery Temperature Sensor "E" Circuit High
P0C36-123 Hybrid Battery Temperature Sensor "F" Circuit High
P0AAF-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit High
P0AB4-123 Hybrid Battery Pack Air Temperature Sensor "B" Circuit High

PROCEDURE

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Powertrain / Hybrid Control / Data List / Inhaling Air Temp.

HINT:

Compare the temperature of the 2 intake air temperature sensors to determine the sensor with the malfunction (Inhaling Air Temp).




NEXT

3.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)
3.CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

d.
U190667E02
2.125,0.854 2.385,1.01 0.26,0.156 10 false z24

Check the connections of the z24 connectors of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.


Result:
Result Proceed to
NG B
OK Go to next step



e.

Visually check the installation condition of the inlet air temperature sensor.

OK:

The inlet air temperature sensor is installed in the correct location and its claws are engaged securely.


Result:
Result Proceed to
The inlet air temperature sensor is installed in the correct location and its claws are engaged securely A
Inlet air temperature sensor is not installed correctly or claws are damaged. C



f.

Install the No. 4 intake duct.


g.

Install the No. 1 hybrid battery shield sub-assembly.



A

4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
U190667E02
2.125,0.854 2.385,1.01 0.26,0.156 10 false z24

Disconnect the z24 battery smart unit connector.


d.
U190651E02
2.344,2.26 2.625,2.229 true 2.229,2.24 2.552,1.896 true 2.125,2.24 2.208,1.969 true 2,2.24 1.969,1.75 true 1.896,2.24 1.583,1.74 true 1.792,2.24 1.25,1.75 true 1.479,2.229 0.896,1.781 true 1.385,2.24 0.854,1.958 true 1.479,2.396 0.948,2.781 true 1.375,2.385 0.781,2.615 true 1.896,2.396 1.458,2.906 true 1.781,2.396 1.177,2.885 true 2.01,2.396 2.156,2.917 true 2.125,2.396 2.438,2.875 true 2.229,2.396 2.542,2.708 true 2.344,2.385 2.656,2.552 true 0.677,2.729 1,2.917 0.323,0.188 10 false TC0 0.521,2.552 0.844,2.74 0.323,0.188 10 false TC1 0.583,1.677 0.938,1.865 0.354,0.188 10 false GC0 0.552,1.875 0.906,2.063 0.354,0.188 10 false GC1 0.198,0.094 0.365,0.25 0.167,0.156 10 false *a 2.375,2.885 2.677,3.073 0.302,0.188 10 false TB2 2.031,2.948 2.333,3.135 0.302,0.188 10 false TB3 1.281,2.917 1.583,3.104 0.302,0.188 10 false TB4 0.958,2.896 1.26,3.083 0.302,0.188 10 false TB5 2.552,2.698 2.854,2.885 0.302,0.188 10 false TB1 2.677,2.49 3.031,2.677 0.354,0.188 10 false TB0 2.656,2.135 2.979,2.323 0.323,0.188 10 false GB0 2.583,1.781 2.885,1.969 0.302,0.188 10 false GB1 2.042,1.76 2.344,1.948 0.302,0.188 10 false GB2 1.771,1.552 2.073,1.74 0.302,0.188 10 false GB3 1.385,1.583 1.688,1.771 0.302,0.188 10 false GB4 0.99,1.594 1.292,1.781 0.302,0.188 10 false GB5 0.698,2.302 0.938,2.49 0.24,0.188 10 false z24

Measure the resistance according to the value(s) in the table below.

Tester Connection
Tester Connection Inlet Air Temperature Sensor No.
z24-21 (TC0) - z24-9 (GC0) 0
z24-22 (TC1) - z24-10 (GC1) 1

Standard Resistance:
Condition Condition Specified Condition
0 °C (32 °F) Power switch off 26.7 to 27.8 kΩ
25 °C (77 °F) Power switch off 9.9 to 10.1 kΩ
40 °C (104 °F) Power switch off 5.73 to 5.92 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z24-21 (TC0) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-9 (GC0) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-22 (TC1) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-10 (GC1) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-13 (TB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-1 (GB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-14 (TB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-2 (GB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-15 (TB2) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-3 (GB2) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-16 (TB3) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-4 (GB3) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-17 (TB4) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-5 (GB4) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-18 (TB5) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-6 (GB5) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z24-21 (TC0) - Body ground Power switch on (IG) Below 1 V
z24-9 (GC0) - Body ground Power switch on (IG) Below 1 V
z24-22 (TC1) - Body ground Power switch on (IG) Below 1 V
z24-10 (GC1) - Body ground Power switch on (IG) Below 1 V
z24-13 (TB0) - Body ground Power switch on (IG) Below 1 V
z24-1 (GB0) - Body ground Power switch on (IG) Below 1 V
z24-14 (TB1) - Body ground Power switch on (IG) Below 1 V
z24-2 (GB1) - Body ground Power switch on (IG) Below 1 V
z24-15 (TB2) - Body ground Power switch on (IG) Below 1 V
z24-3 (GB2) - Body ground Power switch on (IG) Below 1 V
z24-16 (TB3) - Body ground Power switch on (IG) Below 1 V
z24-4 (GB3) - Body ground Power switch on (IG) Below 1 V
z24-17 (TB4) - Body ground Power switch on (IG) Below 1 V
z24-5 (GB4) - Body ground Power switch on (IG) Below 1 V
z24-18 (TB5) - Body ground Power switch on (IG) Below 1 V
z24-6 (GB5) - Body ground Power switch on (IG) Below 1 V


NOTICE:

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the z24 battery smart unit connector.


l.

Install the No. 1 hybrid battery shield sub-assembly.



OK

5.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NG

5.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

OK

NG

6.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR)
6.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR)

OK

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

OK

NG

REPAIR HARNESS OR CONNECTOR OR REPLACE HV BATTERY