Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A9D-123  Hybrid Battery Temperature Sensor "A" Circuit Low  P0A9E-123  Hybrid Battery Temperature Sensor "A" Circuit High  P0AC7-123  Hybrid Battery Temperature Sensor "B" Circuit Low  P0AC8-123  Hybrid Battery Temperature Sensor "B" Circuit High  P0ACC-123  Hybrid Battery Temperature Sensor "C" Circuit Low  P0ACD-123  Hybrid Battery Temperature Sensor "C" Circuit High  P0AEA-123  Hybrid Battery Temperature Sensor "D" Circuit Low  P0AEB-123  Hybrid Battery Temperature Sensor "D" Circuit High  P0BC4-123  Hybrid Battery Temperature Sensor "E" Circuit Low  P0BC5-123  Hybrid Battery Temperature Sensor "E" Circuit High  P0C35-123  Hybrid Battery Temperature Sensor "F" Circuit Low  P0C36-123  Hybrid Battery Temperature Sensor "F" Circuit High  


DESCRIPTION

Refer to the description for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).


DTC No. INF Code DTC Detection Condition Trouble Area
P0A9D
P0A9E
P0AC7
P0AC8
P0ACC
P0ACD
P0AEA
P0AEB
P0BC4
P0BC5
P0C35
P0C36
123 When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection).
·

HV battery

·

Battery smart unit

·

Wire harness or connector

·

Hybrid battery junction block assembly



HINT:

After checking for the above DTCs, check the hybrid system Data List item "Temp of Batt" using the GTS.


Temperature Displayed Malfunction
Below -45°C (-49°F) Open or +B short circuit
95°C (203°F) or more GND short circuit

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).

Refer to the wiring diagram for DTC P0ABF-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0ABF-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

If a short to +B occurs in the battery temperature sensor, battery current sensor or intake air temperature sensor, the following DTCs may be output simultaneously.


DTC No. Relevant Diagnosis
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AEB-123 Hybrid Battery Temperature Sensor "D" Circuit High
P0BC5-123 Hybrid Battery Temperature Sensor "E" Circuit High
P0C36-123 Hybrid Battery Temperature Sensor "F" Circuit High
P0AAF-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit High
P0AB4-123 Hybrid Battery Pack Air Temperature Sensor "B" Circuit High

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 1 to 6.

HINT:

Compare the temperature of the 6 battery temperature sensors to determine the sensor with the malfunction (Temp of Batt TB1 to TB6).




NEXT

4.CHECK CONNECTOR CONNECTION CONDITION (BATTERY TEMPERATURE SENSOR)
4.CHECK CONNECTOR CONNECTION CONDITION (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
U190665E02
2.115,0.854 2.375,1.01 0.26,0.156 10 false z24

Check the connections of the z24 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

5.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

NG

CONNECT SECURELY

5.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

OK

6.CHECK BATTERY SMART UNIT (VIB VOLTAGE)

NG

6.CHECK BATTERY SMART UNIT (VIB VOLTAGE)
NOTICE:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.
U190625E02
1.104,1.552 1.021,1.063 true 0.646,1.563 1.01,0.948 true 0.073,0.063 0.271,0.24 0.198,0.177 10 false *a 0.99,1.573 1.229,1.708 0.24,0.135 10 false VIB 0.5,1.573 0.802,1.781 0.302,0.208 10 false GIB 0.323,0.865 0.583,1.01 0.26,0.146 10 false z24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z24-24 (VIB) - z24-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)


f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG

7.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR)
7.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Disconnect the z25 hybrid battery junction block assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.
U190624E01
2.39,1.04 2.683,1.230 0.292,0.189 10 z25 0.182,0.15 0.352,0.311 0.170,0.162 10 *a 0.768,0.857 1.012,1.019 0.244,0.162 10 VIB 1.528,1.153 1.081,0.975 false 0.745,1.59 1.007,1.752 0.262,0.162 10 GIB 1.528,1.473 1.081,1.651 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z25-1 (VIB) - z25-3 (GIB) Power switch on (IG) 4.6 to 5.4 V


Text in Illustration
*a Front view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the z25 hybrid battery junction block assembly connector.


j.

Install the No. 2 hybrid battery shield sub-assembly.



OK

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (BATTERY SMART UNIT - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)
NOTICE:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Disconnect the z25 hybrid battery junction block assembly connector.


d.
U190666E02
2.125,0.854 2.396,1.01 0.271,0.156 10 false z24

Disconnect the z24 battery smart unit connector.


e.

Measure the resistance according to the value(s) in the tables below.

A398193E01
2.667,1 3.083,1.25 0.417,0.25 4.958,1.323 5.375,1.573 0.417,0.25 3.458,1.094 3.875,0.677 false 3.375,1.094 3.063,0.729 false 3.25,1.469 3.354,1.177 false 3.542,1.667 3.448,1.188 false 6.229,1.458 6.646,1.042 false 6.219,1.698 6.677,2.188 false 5.51,2.125 5.927,1.708 false 5.417,1.031 5.927,1.438 false 0.177,0.115 0.615,0.365 0.438,0.25 10 false *a 4.771,0.156 5.208,0.406 0.438,0.25 10 false *b 2.792,0.563 3.229,0.813 0.438,0.25 10 false GIB 3.927,0.552 4.365,0.802 0.438,0.25 10 false IB1 3.469,1.688 3.906,1.938 0.438,0.25 10 false IB0 3.104,1.5 3.542,1.75 0.438,0.25 10 false VIB 2.76,1.042 3.198,1.292 0.438,0.25 10 false z24 5.042,1.365 5.479,1.615 0.438,0.25 10 false z25 6.646,2.219 7.083,2.469 0.438,0.25 10 false IB0 5.333,2.135 5.771,2.385 0.438,0.25 10 false GIB 6.646,0.865 7.083,1.115 0.438,0.25 10 false IB1 5.125,0.906 5.563,1.156 0.438,0.25 10 false VIB

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z24-11 (IB1) - z25- 2 (IB1) Power switch off Below 1 Ω
z24-12 (GIB) - z25- 3 (GIB) Power switch off Below 1 Ω
z24-23 (IB0) - z25- 4 (IB0) Power switch off Below 1 Ω
z24-24 (VIB) - z25- 1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z24-11 (IB1) or z25- 2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-12 (GIB) or z25- 3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-23 (IB0) or z25- 4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z24-24 (VIB) or z25- 1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)
*b Front view of wire harness connector
(to Hybrid Battery Junction Block Assembly)


f.

Reconnect the z25 hybrid battery junction block assembly connector.


g.

Reconnect the z24 battery smart unit connector.


h.

Install the No. 2 hybrid battery shield sub-assembly.



OK

NG

REPAIR HARNESS OR CONNECTOR OR REPLACE HV BATTERY