Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CAMSHAFT › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301594 CAMSHAFT A

2ZR-FXE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 11811 1.INSTALL NO. 1 CAMSHAFT BEARING

a.

Clean both surfaces of the bearings.


b.

Install the 2 No. 1 camshaft bearings.


c.
A214944E01
0.877,1.431 1.074,1.601 0.198,0.170 10 *1 0.872,1.524 0.455,1.524 0.455,1.524 0.455,3.009 false 0.535,2.629 0.656,2.786 0.120,0.157 10 A 2.369,2.629 2.493,2.779 0.124,0.150 10 B

Using a vernier caliper, measure the distance between the bearing cap edge and the camshaft bearing edge.

Text in Illustration
*1 Vernier Caliper

Standard dimension (A - B):

0.7 mm (0.0276 in.) or less


NOTICE:

Position the bearings to the center of the bearing cap by measuring dimensions A and B.



Hide 11821 2.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean both surfaces of the bearings.


b.

Install the 2 No. 2 camshaft bearings.


c.
A330339E04
0.917,3.99 0.917,4.385 false 1.042,3.385 1.396,3.646 0.354,0.26 10 false A 0.844,4.406 1.313,4.604 0.469,0.198 10 false *1

Using a vernier caliper, measure the distance between the bearing cap edge and the camshaft bearing edge.

Text in Illustration
*1 Vernier Caliper

Standard dimension (A):

1.05 to 1.75 mm (0.0413 to 0.0689 in.)


NOTICE:

Position the bearings to the center of the bearing cap by measuring dimension A.



Hide 13512 3.INSTALL NO. 2 CAMSHAFT

a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


c.

Install the No. 2 camshaft to the camshaft housing.


Hide 13511 4.INSTALL CAMSHAFT

a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


c.

Install the camshaft to the camshaft housing.


Hide 5.INSTALL BEARING CAP

a.

Apply engine oil to the camshaft journals, camshaft housings and bearing caps.


b.
A214947E01
1.246,2.648 1.407,2.822 0.161,0.174 10 *1 0.488,2.944 0.662,3.100 0.174,0.156 10 *2 1.943,2.944 2.117,3.100 0.174,0.156 10 *2 0.793,2.228 1.326,2.609 1.326,2.609 1.99,2.297 false 0.578,2.944 0.578,2.578 false 2.022,2.944 2.022,2.625 false 2.24,2.055 2.475,2.215 0.235,0.161 10 50°

Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.

Text in Illustration
*1 Knock Pin
*2 Camshaft


c.
A214948E04
1.885,1.354 1.99,1.531 0.104,0.177 10 true 1 0.063,0.354 0.26,0.51 0.198,0.156 10 false 10 1.875,0.448 1.979,0.625 0.104,0.177 10 true 2 2.438,1.354 2.542,1.531 0.104,0.177 10 true 3 2.427,0.427 2.531,0.604 0.104,0.177 10 true 4 0.688,1.365 0.792,1.542 0.104,0.177 10 true 5 0.719,0.427 0.823,0.604 0.104,0.177 10 true 6 2.969,1.365 3.073,1.542 0.104,0.177 10 true 7 2.906,0.396 3.01,0.573 0.104,0.177 10 true 8 0.094,1.354 0.198,1.531 0.104,0.177 10 false 9

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 11103 6.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A153836E04
1.406,1.313 1.698,1.406 1.698,1.406 1.698,1.469 false 1.573,0.375 1.458,0.375 1.458,0.375 1.302,0.656 false 0.417,0.531 0.5,0.531 0.5,0.531 0.667,0.698 false 0.24,0.448 0.406,0.604 0.167,0.156 10 false *1 1.604,0.302 1.771,0.458 0.167,0.156 10 false *2 1.625,1.49 1.792,1.646 0.167,0.156 10 false *3

Check that the valve rocker arms are installed as shown in the illustration.

Text in Illustration
*1 Valve Stem Cap
*2 Valve Rocker Arm
*3 Valve Lash Adjuster


b.
A206178E11
0.49,2.531 0.833,2.792 0.833,2.792 1,2.792 false 1.771,2.344 1.885,2.906 1.885,2.906 2.063,2.906 false 0.51,0.823 0.854,0.563 0.854,0.563 1.031,0.563 false 0.104,2.708 0.26,2.885 0.156,0.177 10 false A 0.104,0.469 0.26,0.646 0.156,0.177 10 false B 2.094,2.823 3.031,3.021 0.938,0.198 10 false 3.5 to 4.5 mm 1.063,2.719 1.594,2.917 0.531,0.198 10 false 8.0 mm 1.073,0.5 1.604,0.698 0.531,0.198 10 false 7.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Diameter:
Area Specified Condition
Continuous line 3.5 to 4.5 mm (0.138 to 0.177 in.)
A 8.0 mm (0.315 in.)
B 7.0 mm (0.276 in.)


Application Length A and B:

15 mm (0.591 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A408420N01
2.083,1.979 2.271,2.156 0.188,0.177 10 true 1 2,1.302 2.188,1.49 0.188,0.188 10 true 2 2.104,2.969 2.292,3.156 0.188,0.188 10 true 3 2.583,1.958 2.771,2.146 0.188,0.188 10 true 4 2.625,1.385 2.813,1.573 0.188,0.188 10 true 5 2.688,2.99 2.875,3.177 0.188,0.188 10 true 6 0.719,2.094 0.906,2.281 0.188,0.188 10 true 7 1.354,1.25 1.542,1.417 0.188,0.167 10 true 8 0.99,3.125 1.177,3.313 0.188,0.188 10 true 9 3.219,2.49 3.406,2.677 0.188,0.188 10 true 10 3.208,3.031 3.396,3.219 0.188,0.188 10 true 12 3.188,1.417 3.375,1.604 0.188,0.188 10 true 11 0.063,2.115 0.25,2.302 0.188,0.188 10 true 13 0.125,1.344 0.313,1.531 0.188,0.188 10 true 14 0.094,3.042 0.281,3.229 0.188,0.188 10 true 15 3.219,1.813 3.406,2 0.188,0.188 10 true 16 0.875,1.198 1.063,1.385 0.188,0.188 10 true 17

Set the camshaft and No. 2 camshaft as shown in the illustration.


d.

Install the camshaft housing with the 17 bolts and tighten them in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

After installing the camshaft housing, make sure that the cam lobes are positioned as shown in the illustration.

·

If any of the bolts is loosened during installation, remove the camshaft housing, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing is removed because any of the bolts is loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

After installing the camshaft housing, wipe off any seal packing that seeped out from between the housing and cylinder head.




Hide 13523G 7.INSTALL CAMSHAFT TIMING SPROCKET

a.

Tighten the flange bolt with the camshaft timing sprocket secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 13050 8.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A146265E16
1.313,1.042 0.552,1.604 0.552,1.604 0.552,1.76 false 2.406,0.24 2.271,0.24 2.271,0.24 1.948,1.073 false 2.438,0.167 2.698,0.396 0.26,0.229 10 false *1 0.469,1.771 0.646,1.948 0.177,0.177 10 false *2

Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned as shown in the illustration.

Text in Illustration
*1 Straight Pin
*2 Key Groove

NOTICE:

Do not forcefully push in the camshaft timing gear. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear.



b.
A379389E02
0.823,0.583 1.104,0.156 1.104,0.156 1.292,0.156 false 0.792,1.375 1.458,1.781 1.458,1.781 1.625,1.781 false 0.229,0.24 0.385,0.438 0.156,0.198 10 false A 1.375,0.073 1.635,0.302 0.26,0.229 10 false *1 2.635,0.677 2.792,0.875 0.156,0.198 10 false A 1.688,1.688 1.958,1.917 0.271,0.229 10 false *2

Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

Text in Illustration
*1 Straight Pin
*2 Key Groove

NOTICE:

Do not turn the camshaft timing gear in the retard direction (clockwise).



c.
A146267E22
2.771,0.781 2.604,0.781 2.604,0.781 1.406,1.042 false 1.49,0.177 1.292,0.177 1.292,0.177 1.031,0.906 false 1.521,0.083 2.104,0.333 0.583,0.25 10 false *1 1.469,0.531 1.646,0.708 0.177,0.177 10 false *a 1.427,1.948 1.615,2.125 0.188,0.177 10 false *b 2.802,0.698 3.042,0.938 0.24,0.24 10 false *2

Check that there is no clearance between the camshaft timing gear and camshaft flange.

Text in Illustration
*1 Camshaft Timing Gear
*2 Flange
*a Clearance
*b No Clearance


d.

Tighten the flange bolt with the camshaft timing gear secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.
A214982E05
1.448,1.625 1.667,1.823 0.219,0.198 10 true *a

Check that the camshaft timing gear can move in the retard direction (clockwise) and lock it in the most retarded position.

Text in Illustration
*a Lock


Hide 13561 9.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 10.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A221683E04
0.979,0.563 1.333,0.563 1.333,0.563 1.729,0.958 false 0.781,0.479 0.979,0.677 0.198,0.198 10 true *1

Temporarily install the crankshaft pulley bolt.

Text in Illustration
*1 Timing Gear Key


b.

Turn the crankshaft to position the timing gear key to the top.


c.
A262288E01
0.848,0.261 1.005,0.406 0.157,0.145 10 *1 0.613,0.628 0.613,0.339 0.613,0.339 0.807,0.339 false 1.986,0.25 2.143,0.395 0.157,0.145 10 *2 1.769,0.649 1.769,0.327 1.769,0.327 1.964,0.327 false 0.302,1.016 0.302,1.682 0.302,1.682 1.128,1.682 false 0.924,1.682 0.924,0.993 false 1.149,1.597 1.306,1.743 0.157,0.145 10 *3

Check that the timing marks on the camshaft timing gear and camshaft timing sprocket are aligned as shown in the illustration.

Text in Illustration
*1 Timing Mark (Rectangle)
*2 Timing Mark
*3 Mark (Circle)

NOTICE:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



d.

Remove the crankshaft pulley bolt.


Hide 13506 11.INSTALL CHAIN SUB-ASSEMBLY

a.
A262289E01
1.735,0.629 1.912,0.773 0.177,0.144 10 *2 1.733,0.125 1.909,0.269 0.177,0.144 10 *1 1.598,0.884 1.775,1.028 0.177,0.144 10 *3 0.404,0.783 0.404,0.971 0.404,0.971 1.582,0.971 false 1.087,0.709 1.087,0.97 false 2.602,3.187 1.876,3.349 1.876,3.349 1.876,3.65 false 0.8,3.743 1.399,4.081 false 1.447,4.034 1.623,4.178 0.177,0.144 10 *b 1.773,3.645 1.950,3.789 0.177,0.144 10 *a 0.723,0.268 1.716,0.212 false 0.663,0.356 1.703,0.706 false

Align the mark plate (orange) with the timing mark as shown in the illustration and install the chain.

Text in Illustration
*1 Mark Plate (Orange)
*2 Timing Mark (Rectangle)
*3 Mark (Circle)
*a Place the Chain on the Sprocket
*b Pass the Chain through the Damper

NOTICE:

There are 3 marks on the camshaft timing sprocket. Make sure to align the mark plate with the timing mark (rectangle).


HINT:
·

Be sure to position the mark plate at the front of the engine.

·

The mark plate on the camshaft side is colored orange.

·

Do not pass the chain around the sprocket of the camshaft timing gear. Only place it on the sprocket.

·

Pass the chain through the No. 1 vibration damper.




b.
A150936

Place the chain on the crankshaft without passing it around the shaft.


c.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to align the mark plate (orange) and timing mark, and then install the chain.

A379051E01
2.979,4.781 3.135,4.115 true 3.094,3.99 3.25,3.573 3.25,3.573 3.188,4.031 false 3.969,4.729 4.188,4.042 true 3.177,3.385 3.49,3.583 0.313,0.198 10 false *1 2.875,4.813 3.188,5.01 0.313,0.198 10 false *2 3.896,4.771 4.208,4.969 0.313,0.198 10 false *a

Text in Illustration
*1 Mark Plate (Orange)
*2 Timing Mark
*a Tension the Chain


d.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear clockwise.

HINT:

To tension the chain, slowly turn the camshaft timing gear clockwise to prevent the chain from being misaligned.



e.
A150939E13
1.615,0.146 1.865,0.146 1.865,0.146 2.125,1.719 false 1.969,1.833 1.781,2.958 false 1.417,0.063 1.698,0.25 0.281,0.188 10 false *1 1.698,2.99 1.875,3.188 0.177,0.198 10 false *2

Align the mark plate (yellow or pink) and timing mark and install the chain to the crankshaft timing gear.

Text in Illustration
*1 Mark Plate (Yellow or Pink)
*2 Timing Mark


Hide 12.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Check each timing mark at TDC/compression.

A262290E04
0.75,1.01 0.75,0.729 0.75,0.729 0.646,0.729 false 2.24,1.125 2.24,0.688 2.24,0.688 2.115,0.688 false 0.542,1.469 0.542,2.188 0.542,2.188 1.375,2.188 false 1.125,1.417 1.125,2.188 false 0.75,1.104 0.75,1.229 0.75,1.229 0.188,1.229 false 2.208,1.208 2.208,2.219 2.208,2.219 2.438,2.219 false 6.063,1.771 5.729,1.979 5.729,1.979 5.729,2.219 true 6.167,1.771 6.365,1.969 6.365,1.969 6.365,2.24 true 1.396,2.104 1.583,2.26 0.188,0.156 10 false *5 0.479,0.656 0.646,0.813 0.167,0.156 10 false *2 1.938,0.615 2.094,0.771 0.156,0.156 10 true *2 2.469,2.135 2.656,2.292 0.188,0.156 10 false *1 0.031,1.146 0.188,1.302 0.156,0.156 10 false *4 5.646,2.24 5.833,2.396 0.188,0.156 10 false *1 6.271,2.26 6.458,2.417 0.188,0.156 10 false *3

Text in Illustration
*1 Timing Mark *2 Mark Plate (Orange)
*3 Mark Plate (Yellow or Pink) *4 Timing Mark (Rectangle)
*5 Mark (Circle) - -

NOTICE:

There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



Hide 13562 13.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the No. 2 chain vibration damper with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13559 14.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper to the cylinder block.


Hide 11302 16.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13540 18.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A162975E02
1.656,0.122 2.007,0.289 0.350,0.167 10 *1 0.348,0.651 0.520,0.818 0.172,0.167 10 *a 0.545,2.271 0.708,2.438 0.163,0.167 10 *a 0.981,2.817 1.142,2.968 0.162,0.151 10 *2 0.261,3.618 0.428,3.767 0.167,0.148 10 *2 1.553,2.761 1.708,2.911 0.155,0.150 10 *3 2.073,3.918 2.247,4.070 0.174,0.152 10 *3 0.847,1.803 1.008,1.955 0.161,0.151 10 *b 0.511,3.277 0.673,3.423 0.162,0.146 10 *1 1.275,4.012 2.039,4.012 false 1.019,3.956 0.552,3.708 0.552,3.708 0.449,3.708 false 0.689,3.36 0.818,3.36 0.818,3.36 1.168,3.743 false 1.067,2.638 1.067,2.817 false 1.399,2.448 1.64,2.652 1.64,2.652 1.64,2.751 false 1.625,0.192 1.447,0.192 1.447,0.192 1.214,0.334 false 1.153,1.167 1.341,1.357 0.188,0.189 12 *c 2.575,1.167 2.759,1.344 0.184,0.177 12 *d

Release the cam, and then fully push in the plunger and engage the hook to the pin so that the plunger is in the position shown in the illustration.

Text in Illustration
*1 Cam
*2 Pin
*3 Hook
*a Push
*b Raise
*c CORRECT
*d INCORRECT

NOTICE:

Make sure that the cam engages the first tooth of the plunger to allow the hook to pass over the pin.



b.
A214955

Install a new gasket, the bracket and chain tensioner with the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

If the hook releases the plunger while the chain tensioner is being installed, set the hook again.



c.
A214956E02
0.586,1.875 0.783,2.049 0.198,0.174 10 *c 0.137,2.205 0.295,2.350 0.158,0.145 10 *2 0.758,2.623 0.911,2.765 0.153,0.142 10 *1 1.317,2.836 1.479,2.980 0.162,0.144 10 *b 0.833,2.616 0.833,2.556 0.833,2.556 0.65,2.399 false 0.327,2.293 0.407,2.293 0.407,2.293 0.56,2.335 false 0.35,2.68 0.547,2.854 0.198,0.174 10 *a

Rotate the crankshaft counterclockwise slightly and check that the hook is released.

Text in Illustration
*1 Pin
*2 Hook
*a Push
*b Turn
*c Disconnect


d.
A214957E02
0.855,2.062 1.008,2.203 0.153,0.142 10 *1 0.338,2.746 0.506,2.901 0.168,0.154 10 *b 1.339,2.807 1.497,2.953 0.158,0.146 10 *a 0.855,2.139 0.775,2.139 0.775,2.139 0.624,2.435 false

Turn the crankshaft clockwise and check that the plunger is extended.

Text in Illustration
*1 Plunger
*a Turn
*b Plunger Extended


Hide 11201 21.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23807V 24.INSTALL NO. 1 DELIVERY PIPE SPACER

Hide 23807 25.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 25620 28.INSTALL EGR VALVE WITH COOLER ASSEMBLY

Hide 11409 30.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 34.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE