46200
1.INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY
Install the parking brake control pedal assembly with the 2 bolts and nut.
Connect the parking brake switch connector.
Engage the wire harness clamp.
Using SST, install the bolt (A).
| *a | Fulcrum Length |
Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
This torque value is effective when SST is parallel to the torque wrench.
Install the No. 1 parking brake cable assembly with the 3 bolts.
Install the No. 1 parking brake cable assembly to the clamp.
Engage the 2 wire harness clamps.
Temporarily install the lock nut.
| *1 | Lock Nut |
| *2 | Adjusting Nut |
After adjusting parking brake pedal travel, tighten the lock nut.
46302
2.CONNECT NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY
Connect the No. 1 parking brake pull rod sub-assembly to the parking brake control pedal assembly as shown in the illustration.
| *a | Turn |
| *b | Hold |
87201
3.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY
73900
4.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Use the same procedure as for LHD (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>KNEE AIRBAG ASSEMBLY>INSTALLATION).
55606
5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).
6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).
55550
7.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>INSTALLATION).
55440D
8.INSTALL INSTRUMENT PANEL BOX ASSEMBLY
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION).
55480D
9.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION).
55431B
10.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION).
11.INSTALL INTEGRATION CONTROL AND PANEL
Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION).
G92D2
12.INSTALL NO. 2 HYBRID BATTERY INTAKE DUCT
Engage the 2 guides.
Install the No. 2 hybrid battery intake duct with the 2 clips.
Install the front floor carpet.
87289A
13.INSTALL REAR NO. 1 HEATER REGISTER BEZEL
Install the rear No.1 heater register bezel with the 2 clips.
77306
14.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
62413A
15.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).
73210
16.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side (See page Vehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>INSTALLATION).
73233
17.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
Use the same procedure as for the LH side (See page Vehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>INSTALLATION).
62331A
18.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
67917A
19.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).
62311B
20.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62111C
21.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).
67913
22.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).
G9510
23.INSTALL HV BATTERY
24.ADJUST PARKING BRAKE PEDAL TRAVEL
25.INSPECT BRAKE WARNING LIGHT