1. PRECAUTION
Make sure to select DEF mode before disconnecting the cable from the negative (-) auxiliary battery terminal.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))
3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))
4.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55736D
5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD)
55701J
6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55735C
7.REMOVE COWL BODY MOUNTING REINFORCEMENT RH (for RHD)
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
88707
9.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt and slide the hook connector.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
10.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Disconnect the air conditioner tube and accessory assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
87245A
11.DISCONNECT INLET HEATER WATER HOSE A
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.
Do not apply excessive force to the inlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
87246A
12.DISCONNECT OUTLET HEATER WATER HOSE A
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.
Do not apply excessive force to the outlet heater water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
55303B
13.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
14.REMOVE STEERING POST ASSEMBLY
82877
15.REMOVE ECU INTEGRATION BOX RH (for LHD)
82878
16.REMOVE ECU INTEGRATION BOX LH (for RHD)
82877
17.REMOVE ECU INTEGRATION BOX RH (for RHD)
82730
18.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
85940
19.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)
55309C
20.REMOVE CENTER INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY
Disengage the clamp.
Remove the 2 nuts and center instrument panel reinforcement sub-assembly.
88625Q
21.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Disconnect the aspirator and connector, and remove the cooler thermistor (room temperature sensor).
55377A
22.REMOVE NO. 2 INSTRUMENT PANEL MOUNTING BRACKET
Using a clip remover, remove the clip and turn back the floor carpet.
Remove the bolt and 2 nuts, and No. 2 instrument panel mounting bracket.
55306A
23.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Disengage the 4 clamps.
Remove the screw, nut, and No. 1 instrument panel brace sub-assembly.
55376
24.REMOVE NO. 1 INSTRUMENT PANEL MOUNTING BRACKET
Using a clip remover, remove the clip and turn back the floor carpet.
Remove the 2 bolts, 2 nuts, and No. 1 instrument panel mounting bracket.
55307C
25.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire |
Remove the bolt.
Disengage the clamp.
Remove the 2 bolts.
Disengage the 3 clamps.
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire |
Disengage the 3 clamps.
Remove the screw, nut, and No. 2 instrument panel brace sub-assembly.
55990B
26.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
Disengage the 2 clamps.
Using a clip remover, remove the 2 clips.
Disengage the 2 claws and guide, and remove the lower defroster nozzle assembly.
87212
27.REMOVE REAR NO. 1 AIR DUCT
Disengage the clamp.
Disengage the 8 claws and remove the rear No. 1 air duct.
55330B
28.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Remove the bolt.
Disengage the 3 clamps.
Disengage the 2 clamps.
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire |
Remove the 2 bolts.
Disengage the 4 clamps.
Disconnect the center airbag sensor connector from the center airbag sensor assembly as shown in the illustration.
| *1 | Center Airbag Sensor Connector | - | - |
Disengage the 2 clamps.
Disconnect each connector.
Remove the 9 bolts and instrument panel reinforcement assembly.
29.REMOVE AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause brackets of the air conditioning unit assembly to break.
When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Disconnect the No. 1 cooler unit drain hose.
Remove the bolt and nut, and air conditioning unit assembly.