Home › Engine / Hybrid System › 2ZR-FXE EMISSION CONTROL › EGR VALVE
RM3210E _51 Engine / Hybrid System _047497 2ZR-FXE EMISSION CONTROL _0236605 EGR VALVE A

2ZR-FXE EMISSION CONTROL  EGR VALVE  INSTALLATION  


PROCEDURE

Hide 25620 1.INSTALL EGR VALVE ASSEMBLY

a.
A379107C02
1.01,1.354 0.281,1.146 0.281,1.146 1.125,1.104 true 2.823,1.406 2.906,0.938 2.906,0.938 2.76,1.135 true 0.083,1.031 0.406,1.313 0.323,0.281 10 false *a 2.833,0.75 3.021,0.938 0.188,0.188 10 true *a
*a Claw


Install a new EGR valve gasket to the EGR valve assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.



b.

Set the EGR valve assembly to the EGR pipe with cooler sub-assembly.


c.

Using an E8 "TORX" socket wrench, install the stud bolt to the camshaft housing sub-assembly.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.



d.

Install the EGR valve assembly to the EGR pipe with cooler sub-assembly with the 3 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
A378888C01
2.115,1.885 2.313,2.094 0.198,0.208 10 false *a 1.052,1.938 1.24,2.177 0.188,0.24 10 false *b 1.656,2.5 1.896,2.792 0.24,0.292 10 false *c 1.49,2.802 1.74,3.052 0.25,0.25 10 false *d
*a 0 to 4 mm (0 to 0.157 in.)
*b Up
*c LH
*d 180°


Connect the water by-pass hose to the EGR valve assembly and slide the clip to secure it.


f.
A377701C01
2.125,1.896 2.427,2.156 0.302,0.26 10 false *a 1.073,1.938 1.375,2.156 0.302,0.219 10 false *b 1.656,2.49 1.99,2.76 0.333,0.271 10 false *c 1.521,2.729 1.802,2.969 0.281,0.24 10 false *d
*a 0 to 4 mm (0 to 0.157 in.)
*b Up
*c LH
*d 180°


Connect the No. 6 water by-pass hose to the EGR valve assembly and slide the clip to secure it.


g.

Connect the EGR valve assembly connector.


Hide G9200 3.INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Wear insulated gloves.


NOTICE:
·

Be careful not to damage the surrounding components when installing the inverter with converter assembly.

·

To prevent damage to the inverter with converter assembly, do not hold the coolant pipe, bracket or connector when securing the inverter with converter assembly.

·

To prevent damage due to static electricity, do not touch the terminals of the inverter with converter assembly connector.

·

Make sure to seal the inverter with converter assembly with the connector cover assembly or tape (non-residue type) etc., until just before installing the inverter with converter assembly to prevent entry of foreign matter and water.



a.

Remove the rope or equivalent that was securing the inverter with converter assembly.


b.

Temporarily install the inverter with converter assembly with the 5 bolts and 2 nuts.

NOTICE:
A380098C01
0.479,2.198 0.667,2.396 0.188,0.198 10 true *a 0.469,3.396 0.646,3.573 0.177,0.177 10 true *b
*a Correct
*b Incorrect


Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.



c.

Tighten the bolt (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

A378886C02
1.99,0.417 2.146,0.615 0.156,0.198 10 true A 1.573,0.438 1.729,0.635 0.156,0.198 10 true B 1.083,0.375 1.229,0.563 0.146,0.188 10 true B 0.708,0.469 0.854,0.646 0.146,0.177 10 true B 6.438,2.302 6.594,2.5 0.156,0.198 10 true C
V100135

Bolt
V100136

Nut



d.

Tighten the 3 bolts (B).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


e.

Tighten the bolt (C).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


f.

Tighten the 2 nuts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 82121 6.CONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A377693E01
0.635,1.698 0.802,1.896 0.167,0.198 10 true A 2.521,1.583 2.688,1.792 0.167,0.208 10 true A 1.177,3.49 1.344,3.688 0.167,0.198 10 true B

Engage the 4 clamps.


b.

Install the 2 bolts (A).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Install the bolt (B).

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


d.
A376381

Move the 2 lock levers as shown in the illustration and connect the 2 inverter with converter assembly connectors.

NOTICE:
·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.

·

Insulate the disconnected terminals with insulating tape.

·

Do not touch the waterproof seal or terminals of the connector.




e.
A376303

Engage the 2 claws.


f.

Connect the 3 No. 1 engine room relay block and No. 1 junction block assembly connectors.


g.

Install the No. 1 relay block cover.


h.
A378887

Connect the ECM connector and lower the lever.

NOTICE:
·

When connecting the ECM connector, make sure that the connecting part of the ECM connector is free of dirt, water or other foreign matter.

·

Be sure to securely connect the ECM connector.




Hide 74404A 7.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 10.ADD ENGINE COOLANT (for Engine)

Hide 11.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51444C 12.INSTALL REAR MOTOR UNDER COVER LH

Hide 55701J 13.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55736D 14.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 15.INSTALL WATER GUARD PLATE LH

Hide 55737B 16.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55738D 17.INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 12601B 19.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY