Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly (meter circuit plate) detects an open in a turn signal light circuit, or a short in a turn signal light circuit or the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

Bulb

·

Harness or connector

·

Instrument panel junction block assembly

·

Combination meter assembly (Meter circuit plate)


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

Bulb

·

Harness or connector

·

Instrument panel junction block assembly

·

Combination meter assembly (Meter circuit plate)


DTC stored -

WIRING DIAGRAM

E342173E01
6.063,0.615 6.677,0.813 0.615,0.198 10 false TRNL 6.083,3.958 6.698,4.156 0.615,0.198 10 false TRNR 5.833,0.5 6.448,0.698 0.615,0.198 10 false 13 5.896,3.844 6.51,4.042 0.615,0.198 10 false 7 5.25,0.615 5.865,0.813 0.615,0.198 10 false 3A 5.25,3.938 5.865,4.135 0.615,0.198 10 false 3A 5.313,3.76 5.927,3.958 0.615,0.198 10 false 4 5.313,0.417 5.927,0.615 0.615,0.198 10 false 5 3.771,0.615 4.385,0.813 0.615,0.198 10 false 3F 3.76,1.719 4.375,1.917 0.615,0.198 10 false 3H 3.76,2.823 4.375,3.021 0.615,0.198 10 false 3H 3.771,3.938 4.385,4.135 0.615,0.198 10 false 3F 3.75,5.042 4.365,5.24 0.615,0.198 10 false 3H 3.76,6.156 4.375,6.354 0.615,0.198 10 false 3H 3.813,0.417 4.427,0.615 0.615,0.198 10 false 6 3.771,1.531 4.385,1.729 0.615,0.198 10 false 13 3.771,2.635 4.385,2.833 0.615,0.198 10 false 14 3.813,3.75 4.427,3.948 0.615,0.198 10 false 8 3.771,4.854 4.385,5.052 0.615,0.198 10 false 17 3.771,5.958 4.406,6.156 0.635,0.198 10 false 16 5.302,4.521 7.125,5.271 1.823,0.75 10 false Combination Meter Assembly (Meter Circuit Plate) 5.302,4.375 5.917,4.573 0.615,0.198 10 false F7 3.896,6.615 5.531,7.063 1.635,0.448 10 false Instrument Panel Junction Block Assembly 2.667,0.5 3.281,0.698 0.615,0.198 10 false 1 1.292,0.51 1.906,0.708 0.615,0.198 10 false 2 1.302,1.615 1.917,1.813 0.615,0.198 10 false 2 2.667,1.604 3.281,1.802 0.615,0.198 10 false 3 1.229,2.719 1.844,2.917 0.615,0.198 10 false 11 2.656,2.729 3.271,2.927 0.615,0.198 10 false 10 1.479,2.719 2.094,2.917 0.615,0.198 10 false E 2.448,2.729 3.063,2.927 0.615,0.198 10 false B 1.5,1.625 2.115,1.823 0.615,0.198 10 false E 1.49,0.51 2.104,0.708 0.615,0.198 10 false E 2.458,1.604 3.073,1.802 0.615,0.198 10 false B 2.458,0.5 3.073,0.698 0.615,0.198 10 false B 1.292,3.833 1.906,4.031 0.615,0.198 10 false 2 2.656,3.833 3.271,4.031 0.615,0.198 10 false 1 1.49,3.833 2.104,4.031 0.615,0.198 10 false E 2.448,3.833 3.063,4.031 0.615,0.198 10 false B 1.292,4.927 1.906,5.125 0.615,0.198 10 false 2 1.49,4.938 2.104,5.135 0.615,0.198 10 false E 2.458,4.938 3.073,5.135 0.615,0.198 10 false B 2.656,4.938 3.271,5.135 0.615,0.198 10 false 3 1.479,6.052 2.094,6.25 0.615,0.198 10 false E 2.469,6.063 3.083,6.26 0.615,0.198 10 false B 1.219,6.052 1.833,6.25 0.615,0.198 10 false 11 2.688,6.052 3.302,6.25 0.615,0.198 10 false 10 1.323,0.99 1.938,1.188 0.615,0.198 10 false A27 1.313,1.146 3.208,1.375 1.896,0.229 10 false Headlight Assembly LH 0.927,1.979 1.542,2.177 0.615,0.198 10 false M43 0.917,2.135 3.542,2.396 2.625,0.26 10 false Rear Combination Light Assembly LH 1.042,3.167 1.656,3.365 0.615,0.198 10 false J8 1.021,3.333 3.635,3.563 2.615,0.229 10 false Side Turn Signal Light Assembly LH 1.333,4.302 1.948,4.5 0.615,0.198 10 false A13 1.344,4.458 3.958,4.688 2.615,0.229 10 false Headlight Assembly RH 1.052,5.396 1.667,5.594 0.615,0.198 10 false M42 1.042,5.552 3.656,5.781 2.615,0.229 10 false Rear Combination Light Assembly RH 1.073,6.406 1.688,6.604 0.615,0.198 10 false I8 1.052,6.563 3.667,6.792 2.615,0.229 10 false Side Turn Signal Light Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following procedure.

Side turn signal light assembly: Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION

Rear combination light assembly: Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
All RH turn signal lights or all LH turn signal lights do not blink. A
RH side turn signal light does not blink or flash at the correct speed. B
LH side turn signal light does not blink or flash at the correct speed. C



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

4.CHECK TURN SIGNAL LIGHTS (RH SIDE)

C

11.CHECK TURN SIGNAL LIGHTS (LH SIDE)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

RH side

i.

Disconnect the F7 combination meter assembly (meter circuit plate) connector.


ii.

Disconnect the 3A instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F7-7 (TRNR) - 3A-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F7-7 (TRNR) or 3A-4 - Body ground Always 10 kΩ or higher




b.

LH side

i.

Disconnect the F7 combination meter assembly (meter circuit plate) connector.


ii.

Disconnect the 3A instrument panel junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F7-13 (TRNL) - 3A-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F7-13 (TRNL) or 3A-5 - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E342174C01
1.99,0.302 2.354,0.531 0.365,0.229 1.927,2.125 2.292,2.354 0.365,0.229 5.333,0.281 5.698,0.51 0.365,0.229 0.24,0.177 0.552,0.333 0.313,0.156 10 false *a 2.083,0.333 2.396,0.49 0.313,0.156 10 false 3A 2.021,2.156 2.333,2.313 0.313,0.156 10 false 3H 5.427,0.313 5.74,0.469 0.313,0.156 10 false 3F
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

RH side

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - 3F-8 Always Below 1 Ω
3A-4 - 3H-17 Always Below 1 Ω
3A-4 - 3H-16 Always Below 1 Ω




c.

LH side

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-5 - 3F-6 Always Below 1 Ω
3A-5 - 3H-13 Always Below 1 Ω
3A-5 - 3H-14 Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the power switch on (IG).


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light RH does not blink or flash at the correct speed. A
Side turn signal light RH does not blink or flash at the correct speed. B
Rear turn signal light RH does not blink or flash at the correct speed. C



A

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

C

9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the A13 headlight assembly RH connector.


b.

Disconnect the 3F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A13-1 (B) - 3F-8 Always Below 1 Ω
A13-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A13-1 (B) or 3F-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E274732C10
1.896,0.583 2.365,0.854 0.469,0.271 5.313,0.542 5.781,0.813 0.469,0.271 2.042,0.646 2.563,0.948 0.521,0.302 10 false 3A 5.458,0.615 5.979,0.917 0.521,0.302 10 false 3F 0.448,0.292 0.969,0.594 0.521,0.302 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - 3F-8 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the I8 side turn signal light assembly RH connector.


b.

Disconnect the 3H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I8-10 (B) - 3H-16 Always Below 1 Ω
I8-11 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
I8-10 (B) or 3H-16 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E274731C16
1.771,0.563 2.271,0.854 0.5,0.292 5.354,0.542 5.854,0.833 0.5,0.292 0.365,0.427 0.854,0.781 0.49,0.354 10 false *a 1.927,0.635 2.708,1.115 0.781,0.479 10 false 3A 5.521,0.615 6.302,1.094 0.781,0.479 10 false 3H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - 3H-16 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the M42 rear combination light assembly RH connector.


b.

Disconnect the 3H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M42-3 (B) - 3H-17 Always Below 1 Ω
M42-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
M42-3 (B) or 3H-17 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E274731C16
1.771,0.563 2.271,0.854 0.5,0.292 5.354,0.542 5.854,0.833 0.5,0.292 0.365,0.427 0.854,0.781 0.49,0.354 10 false *a 1.927,0.635 2.708,1.115 0.781,0.479 10 false 3A 5.521,0.615 6.302,1.094 0.781,0.479 10 false 3H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-4 - 3H-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

11.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the power switch on (IG).


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light LH does not blink or flash at the correct speed. A
Side turn signal light LH does not blink or flash at the correct speed. B
Rear turn signal light LH does not blink or flash at the correct speed. C



A

12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

14.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

C

16.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
12.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the A27 headlight assembly LH connector.


b.

Disconnect the 3F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A27-1 (B) - 3F-6 Always Below 1 Ω
A27-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A27-1 (B) or 3F-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E274732C10
1.896,0.583 2.365,0.854 0.469,0.271 5.313,0.542 5.781,0.813 0.469,0.271 2.042,0.646 2.563,0.948 0.521,0.302 10 false 3A 5.458,0.615 5.979,0.917 0.521,0.302 10 false 3F 0.448,0.292 0.969,0.594 0.521,0.302 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-5 - 3F-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the J8 side turn signal light assembly LH connector.


b.

Disconnect the 3H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J8-10 (B) - 3H-14 Always Below 1 Ω
J8-11 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J8-10 (B) or 3H-14 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E274731C16
1.771,0.563 2.271,0.854 0.5,0.292 5.354,0.542 5.854,0.833 0.5,0.292 0.365,0.427 0.854,0.781 0.49,0.354 10 false *a 1.927,0.635 2.708,1.115 0.781,0.479 10 false 3A 5.521,0.615 6.302,1.094 0.781,0.479 10 false 3H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-5 - 3H-14 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the M43 rear combination light assembly LH connector.


b.

Disconnect the 3H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M43-3 (B) - 3H-13 Always Below 1 Ω
M43-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
M43-3 (B) or 3H-13 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E274731C16
1.771,0.563 2.271,0.854 0.5,0.292 5.354,0.542 5.854,0.833 0.5,0.292 0.365,0.427 0.854,0.781 0.49,0.354 10 false *a 1.927,0.635 2.708,1.115 0.781,0.479 10 false 3A 5.521,0.615 6.302,1.094 0.781,0.479 10 false 3H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-5 - 3H-13 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY