Home › Drivetrain › P610 HYBRID TRANSMISSION / TRANSAXLE › ELECTRONIC SHIFT LEVER SYSTEM
RM3210E _52 Drivetrain _047503 P610 HYBRID TRANSMISSION / TRANSAXLE _0243554 ELECTRONIC SHIFT LEVER SYSTEM C

P610 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P1C8A49  Park Pawl Motor (Leaning Value of Shift Immovable Scope) Internal Electronic Failure  


DESCRIPTION

Refer to the description for DTC P1C8949.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>P1C8949

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1C8A49 Park Pawl Motor (Leaning Value of Shift Immovable Scope) Internal Electronic Failure Malfunction of the power system, such as when the auxiliary battery is discharged, an open or short occurs in the P-CON relay, shift control actuator assembly (parking lock motor or rotation angle sensor) or wire harness, or an internal malfunction of the shift control actuator assembly (parking lock motor or rotation angle sensor).
·

Hybrid vehicle control ECU

·

Auxiliary battery

·

Shift control actuator assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


·

Master Warning Light

·

Comes on



·

Multi-information Display Error Message

·

Displayed



DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY

1.

Turn the power switch on (IG).

2.

With the brake pedal depressed, select neutral (N).

3.

Push the P position switch (transmission shift main switch).



WIRING DIAGRAM

Refer to the wiring diagram for DTC P1C8949.

Click hereDrivetrain>P610 HYBRID TRANSMISSION / TRANSAXLE>ELECTRONIC SHIFT LEVER SYSTEM>P1C8949

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove/install the auxiliary battery or disconnect the cable from the negative (-) auxiliary battery terminal before instructed.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Check if DTCs are output.

Result:
Result Proceed to
None of the DTCs in the table below are output. A
Any of the DTCs in the table below are output. B


Priority Relevant DTC
1 P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P06881F ECM/PCM Power Relay Sense Circuit Intermittent
2 P1C8F14 Park Pawl Motor Phase U Circuit Short to Ground or Open
P1C9414 Park Pawl Motor Phase V Circuit Short to Ground or Open
P1C9914 Park Pawl Motor Phase W Circuit Short to Ground or Open
3 P056014 System Voltage (BATT) Circuit Short to Ground or Open

HINT:

Perform troubleshooting for higher priority DTCs first.



e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM, ELECTRONIC SHIFT LEVER SYSTEM)

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Release the brake pedal and turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P1C8A49.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Hybrid Control
Tester Display
BATT Voltage for Transmission Control System

Result:
Result Proceed to
BATT Voltage for Transmission Control System is 9 V or more. A
BATT Voltage for Transmission Control System is less than 9 V. B


e.

Turn the power switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC

NEXT

4.CHARGE AUXILIARY BATTERY
4.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
5.CHECK DTC OUTPUT (SIMULATION TEST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Depress the brake pedal and select neutral (N).


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P1C8A49 is output. A
DTC P1C8A49 is not output. B


f.

Turn the power switch off.



A

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)

B

END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT CONTROL ACTUATOR ASSEMBLY)

OK

7.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (ROTATION ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (ROTATION ANGLE SENSOR)

OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

OK

9.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

OK

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY
a.
A376625C01
1.406,0.5 1.625,0.667 0.219,0.167 10 true *a 1.063,1.26 1.281,1.427 0.219,0.167 10 true *b 1.042,0.813 1.26,0.979 0.219,0.167 10 true *c
*a Lock
*b Unlock
*c Rotate approximately 20°


Wrap the shaft with a piece of cloth and turn it using pliers.

OK:

The shaft rotates smoothly in the lock and unlock directions.


NOTICE:
·

Rotate the shaft using torque between 4.0 and 7.0 N*m (41 and 71 kgf*cm, 36 and 61 in.*lbf).

·

During this inspection, make sure to use a piece of cloth to prevent the shaft splines from being damaged.




b.

Set the shaft in the lock position after the inspection.


Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (AUXILIARY BATTERY VOLTAGE FOR TRANSMISSION CONTROL SYSTEM)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

11.READ VALUE USING GTS (AUXILIARY BATTERY VOLTAGE FOR TRANSMISSION CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Battery Voltage for Transmission Control System.

Powertrain > Hybrid Control > Data List
Tester Display
Auxiliary Battery Voltage for Transmission Control System
50003 397 267

d.

According to the display on the GTS, read the Data List.

Result:
Tester Display Measurement Item Range Normal Condition
Auxiliary Battery Voltage for Transmission Control System BATT voltage value Min: 0.00 V, Max:79.99 V power switch on (IG): 8.00 to 16.00 V



e.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

CHECK AND REPAIR POWER SOURCE CIRCUIT