Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244744 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
C350920

Install the 7 hole plugs to the rear suspension member sub-assembly as shown in the illustration.


Hide 51284 2.INSTALL REAR SUSPENSION MEMBER HOLE COVER

a.

Install the 4 rear suspension member hole covers to the rear suspension member sub-assembly.


Hide 48790 3.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 4.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51206A 5.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C345780C02
0.833,4.365 0.833,3.958 true 2.802,3.875 2.802,3.729 2.802,3.729 3,3.729 true 1.781,4.417 1.781,4.01 true 2.469,4.354 2.469,3.948 true 2.167,3.635 2.51,3.115 2.51,3.115 2.74,3.115 true 3.042,3.656 3.354,3.813 0.313,0.156 10 false *a 0.74,4.396 1.052,4.552 0.313,0.156 10 false *b 1.708,4.438 2.021,4.594 0.313,0.156 10 false *b 2.385,4.375 2.698,4.531 0.313,0.156 10 false *b 2.771,3.031 3.083,3.188 0.313,0.156 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C345782

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.


c.

Install the rear suspension member sub-assembly with the 2 bolts and 2 nuts.

Torque:
143 N*m (1458 kgf*cm, 105 ft.*lbf)


Hide 48790 6.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Temporarily install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




Hide 48770A 7.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 8.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 9.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 10.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 11.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 12.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 13.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48231B 14.INSTALL REAR COIL SPRING LH

Hide 48231A 15.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 16.INSTALL REAR STABILIZER BAR

Hide 89408C 17.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

a.

Install the rear height control sensor sub-assembly LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the connector and engage the 2 clamps.


Hide 47319F 18.CONNECT REAR FLEXIBLE HOSE LH

a.

Connect the rear flexible hose LH to the flexible hose bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 47318F 19.CONNECT REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 48840A 21.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 22.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 23.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 24.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 25.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 26.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 27.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48770A 28.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 57628C 29.INSTALL REAR FLOOR SIDE MEMBER COVER LH

Hide 58390 30.INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY

Hide 17430 31.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 32.INSTALL REAR WHEEL

Hide 48740F 33.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 34.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 36.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 37.PERFORM INITIALIZATION

Intelligent clearance sonar system
Simple intelligent parking assist system
(Click here)
Parking assist monitor system (Click here)
Automatic headlight beam level control system (Click here)