Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM3210E _53 Suspension _047536 REAR SUSPENSION _0244744 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple intelligent parking assist system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Rear height control sensor sub-assembly LH

·

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)


Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 17430 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 57628C 3.REMOVE REAR FLOOR SIDE MEMBER COVER LH

Hide 58390 4.REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY

Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE LH

a.

Remove the bolt and separate the rear flexible hose LH from the flexible hose bracket.


Hide 47318F 6.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89408C 7.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

a.
C345777

Disconnect the connector and disengage the 2 clamps.


b.

Remove the 2 bolts and rear height control sensor sub-assembly LH.


Hide 48840A 8.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 9.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 10.REMOVE REAR STABILIZER BAR

Hide 48231B 11.REMOVE REAR COIL SPRING LH

Hide 48231A 12.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 13.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 14.REMOVE REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 15.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 16.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 17.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 18.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 19.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C348540

Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48770A 20.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51206A 21.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C345780C02
0.833,4.365 0.833,3.958 true 2.802,3.875 2.802,3.729 2.802,3.729 3,3.729 true 1.781,4.417 1.781,4.01 true 2.469,4.354 2.469,3.948 true 2.167,3.635 2.51,3.115 2.51,3.115 2.74,3.115 true 3.042,3.656 3.354,3.813 0.313,0.156 10 false *a 0.74,4.396 1.052,4.552 0.313,0.156 10 false *b 1.708,4.438 2.021,4.594 0.313,0.156 10 false *b 2.385,4.375 2.698,4.531 0.313,0.156 10 false *b 2.771,3.031 3.083,3.188 0.313,0.156 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
·
C345782


·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.



b.

Remove the 2 bolts and 2 nuts.


c.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48790 22.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 23.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51284 24.REMOVE REAR SUSPENSION MEMBER HOLE COVER

a.
C350921C02
0.073,0.073 0.385,0.302 0.313,0.229 10 true *a 0.083,2.552 0.375,2.76 0.292,0.208 10 false *b
*a for LH Side
*b for RH Side


Remove the 4 rear suspension member hole covers from the rear suspension member sub-assembly as shown in the illustration.


Hide 25.REMOVE HOLE PLUG

a.
C350920

Remove the 7 hole plugs from the rear suspension member sub-assembly as shown in the illustration.