INSTALLATION
Removal / installation · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1. INSTALL REAR DIFFERENTIAL SUPPORT |
![]() ![]() |
Install the differential support to the differential carrier with the 4 bolts.
- Torque:
- 98 N*m{ 999 kgf*cm , 72 ft.*lbf }
| 2. INSTALL REAR DIFFERENTIAL NO. 1 AND NO. 2 SUPPORT |
![]() ![]() |
Install the differential No. 1 and No. 2 supports with the 4 bolts to the differential carrier.
- Torque:
- 55 N*m{ 561 kgf*cm , 41 ft.*lbf }
| 3. INSTALL REAR DIFFERENTIAL DYNAMIC DAMPER |
Install the damper front side with the 2 bolts to the No. 1 support.
- Torque:
- 33 N*m{ 337 kgf*cm , 24 ft.*lbf }
Install the damper rear side with the 2 bolts to the differential support.
- Torque:
- 33 N*m{ 337 kgf*cm , 24 ft.*lbf }
| 4. INSTALL DIFFERENTIAL CARRIER SUB-ASSEMBLY |
Support the rear differential carrier with a transmission jack or equivalent.
Apply hypoid gear oil to the splines of the left and right rear drive shaft inboard joints.
Align the splines of the rear drive shaft inboard joints and, using a brass bar and hammer, tap in the left and right rear drive shafts.

- NOTICE:
- Face the cutout section of the snap ring downward.
- Do not damage the oil seal during the insertion.
- Do not strike the tip of the outboard joint with the hammer.
- Face the cutout section of the snap ring downward.
- HINT:
- Determine whether or not the rear drive shaft is completely tapped in by checking for changes in sound or the reaction force of the brass bar.
Slowly raise the transmission jack, install the 3 bolts.

- Torque:
- 86 N*m{ 877 kgf*cm , 63 ft.*lbf } for bolt A
- 140 N*m{ 1,428 kgf*cm , 103 ft.*lbf } for bolt B
- NOTICE:
- Tighten the bolts, not the nuts.
Connect the connector.

Install the breather tube.
Connect the harness clamp.
| 5. INSTALL REAR SUSPENSION MEMBER BRACE LH |
Install the member brace with the 2 bolts to the suspension member.
- Torque:
- 60 N*m{ 612 kgf*cm , 44 ft.*lbf }
| 6. INSTALL REAR SUSPENSION MEMBER BRACE RH |
- HINT:
- Use the same procedures described for the LH side.
| 7. TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
Align the matchmarks of the transfer and propeller shaft.

Temporarily install the propeller shaft with center bearing with the 4 nuts and 4 washers.
Align the matchmarks of the differential carrier and propeller shaft.

Temporarily install the propeller shaft with center bearing with the 4 bolts and 4 washers.
Temporarily install the center support bearing and center support bearing washer with the 2 bolts.

| 8. TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
Tighten the 4 nuts of the propeller shaft and transfer to the torque specification.
- Torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
Tighten the 4 nuts of the propeller shaft and differential carrier to the torque specification.
- Torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
Check that the center line of the center support bearing housing is perpendicular to the axis of the propeller shaft.
Tighten the 2 bolts of the center support bearing to the torque specification.
- Torque:
- 36.8 N*m{ 375 kgf*cm , 27 ft.*lbf }
| 9. INSPECT JOINT ANGLE |
- NOTICE:
- Perform the measurement with a 4 post lift or pit so that the vehicle is supported by all 4 wheels as if it were on the ground.
Before the angle measurement, stabilize each part by performing procedures like those described below.
Rotate the propeller shaft several times by hand.
Set the jack to the differential, and raise and lower the differential.
Using SST and a straightedge, measure the angle of the transfer flange (angle D) and the angle of the intermediate shaft (angle A).
- SST
- 09370-50010
- NOTICE:
- Make sure the straightedge and SST are at a right angle.


Subtract the measured angle of the intermediate shaft (angle A) from the measured angle of the transfer flange (angle D) to obtain the No. 1 joint angle.
- No. 1 Joint Angle:
Measurement Position
No. 1 Joint Angle
D - A
2°27' +/-60'
Using SST, measure the angle of the intermediate shaft (angle A) and the angle of the propeller shaft (angle B).
- SST
- 09370-50010


Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the intermediate shaft (angle A) to obtain the No. 2 joint angle.
- No. 2 Joint Angle:
Measurement Position
Engine
Transmission
No. 2 Joint Angle
A - B
1AZ-FE
A/T
1°29' +/-1°30'
M/T
1°28' +/-1°30'
2AZ-FE
A/T
1°35' +/-1°30'
M/T
1°34' +/-1°30'
2GR-FE
A/T
1°35' +/-1°30'
2AD-FTV
2AD-FHV
M/T
1°28' +/-1°30'
Using SST, measure the angle of the propeller shaft (angle B) and the angle of the rear differential (angle C).
- SST
- 09370-50010


Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the rear differential (angle C) to obtain the No. 3 joint angle.
- No. 3 Joint Angle:
Measurement Position
Engine
Transmission
No. 3 Joint Angle
B - C
1AZ-FE
A/T
2°10' +/-60'
M/T
2°11' +/-60'
2AZ-FE
A/T
2°04' +/-60'
M/T
2GR-FE
A/T
2°04' +/-60'
2AD-FTV
2AD-FHV
M/T
2°10' +/-60'
| 10. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
- HINT:
- 2AD-FTV: (Click here for CCO, Click here for DPF).
- 2AD-FHV: (Click here).
- 2AD-FTV: (Click here for CCO, Click here for DPF).
| 11. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
- HINT:
- 1AZ-FE: (Click here).
- 2AZ-FE: (Click here).
- 1AZ-FE: (Click here).
| 12. INSTALL TAILPIPE ASSEMBLY |
- HINT:
- 1AZ-FE: (Click here).
- 2AD-FTV: (Click here for CCO, Click here for DPF).
- 2AD-FHV: (Click here).
- 2AZ-FE: (Click here).
- 1AZ-FE: (Click here).
| 13. INSTALL FUEL TANK ASSEMBLY |
Install the fuel tank for 1AZ-FE (Click here).
Install the fuel tank for 2AD-FTV (Click here).
Install the fuel tank for 2AD-FHV (Click here).
Install the fuel tank for 2AZ-FE (Click here).
| 14. ADD DIFFERENTIAL OIL |
Add differential oil (Click here).
| 15. CHECK FOR DIFFERENTIAL OIL LEAKAGE |
| 16. CHECK FOR EXHAUST GAS LEAKAGE |
- If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


