2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are the LH side.


1. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

C127536
  1. Install the dust cover to the steering knuckle.

  1. Install the axle hub with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }

    NOTICE:
    Do not place the hub and bearing's magnet rotor side so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.


2. INSTALL FRONT LOWER BALL JOINT ASSEMBLY LH
  1. Install the lower ball joint with the nut to the steering knuckle.

    Torque:
    133 N*m{ 1,360 kgf*cm , 98 ft.*lbf }

  1. Install a new cotter pin.

    1. If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.


3. INSTALL STEERING KNUCKLE WITH AXLE HUB
  1. Align the shaft splines and drive in the drive shaft.

  1. Install the steering knuckle with axle hub with the 2 bolts and 2 nuts.

    Torque:
    240 N*m{ 2,447 kgf*cm , 177 ft.*lbf }

    NOTICE:
    Do not tighten the bolts.


4. CONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH
  1. Connect the lower arm to the ball joint with the 2 bolts and nut.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }


5. CONNECT TIE ROD END SUB-ASSEMBLY LH

C132132
  1. Connect the tie rod end onto the steering knuckle with the castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut up to 60° further.

  1. Install a new cotter pin.


6. INSTALL FRONT SPEED SENSOR LH

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127961E01
    Set the sensor body to the knuckle, and then install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  1. Install the sensor clamp and sensor clip as follows.

    C127962E02

    1. Set the flexible hose clamp on the flexible hose bracket.

    2. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the part of the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) to the part of the flexible hose bracket (labeled D).

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    3. Tighten together the sensor clamp and the flexible hose clamp to the flexible hose bracket with the bolt (labeled E).

      Torque:
      18.5 N*m{ 189 kgf*cm , 14 ft.*lbf }

    4. Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.

  1. C127963E02
    Install the sensor clamp, and sensor clip as follows.

    1. Set the sensor clamp (labeled G) on the side member, and then tighten it with the bolt (labeled H).

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Insert the sensor clip (labeled I) into the hole on the apron.

  1. C127964E01
    Connect the sensor connector.


7. CHECK FRONT AXLE HUB BEARING
  1. Check the axle hub bearing (Click here).


8. INSTALL FRONT DISC

  1. C127063E01
    Put matchmarks on the disc and axle hub.

  1. Remove the disc.


9. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

  1. C127069E01
    Apply silicon grease (Multemp SI-B) on the contact surfaces of the cylinder parts indicated by the arrows.

  1. C127058
    Install the cylinder with the 2 bolts.

    Torque:
    34.3 N*m{ 350 kgf*cm , 25 ft.*lbf }


10. INSTALL FRONT AXLE SHAFT LH NUT
  1. Install a new hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 159 ft.*lbf } for φ 26
    292 N*m{ 2,978 kgf*cm , 215 ft.*lbf } for φ 30

  1. C129484
    Using a chisel and hammer, stake the hub nut.


11. ADD AUTOMATIC TRANSAXLE FLUID
  1. Add the automatic transaxle for U140F (Click here).

  1. Add the automatic transaxle for U241E (Click here).


12. ADD TRANSAXLE OIL
  1. Add the transaxle oil for E352F/E359 (Click here).

  1. Add the transaxle oil for E352 (Click here).

  1. Add the transaxle oil for EA64F (Click here).


13. CHECK FOR AUTOMATIC TRANSAXLE FLUID LEAKAGE

14. CHECK FOR TRANSAXLE OIL LEAKAGE

15. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


16. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the wheel alignment (Click here).


17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

18. CHECK SPEED SENSOR SIGNAL
  1. Check the speed sensor signal for ABS (Click here).

  1. Check the speed sensor signal for VSC (Click here).

← REMOVAL (from Aug 2007)INSTALLATION (Jan 2007 – Jul 2007) →