DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |

| *1 | VVT Sensor |
| *2 | CKP Sensor |
| *3 | ECM |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders is detected (2 trip detection logic). |
|
| P0301 P0302 P0303 P0304 | Misfiring of a specific cylinder is detected (2 trip detection logic). |

| Engine Speed | Duration |
| Idling | 8 minutes or more |
| 1000 | 4 minutes 30 seconds or more |
| 2000 | 2 minutes 30 seconds or more |
| 3000 | 1 minute 30 seconds or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 3.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (MISFIRE COUNT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 (to #4) Misfire Count.
Drive the vehicle at the engine speed and engine load noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedure above.
Read Cylinder #1 (to #4) Misfire Count or the DTCs displayed on the tester.
| Misfire Count | Proceed to |
| Most misfires occur in only 1 or 2 cylinders, or misfire DTCs for only 1 or 2 cylinders are output | A |
| 3 cylinders or more have equal misfire counts, or misfire DTCs for 3 or more cylinders are output | B |
|
| ||||
| A | |
| 5.CHECK SPARK PLUG |
Check the spark plug .
|
| ||||
| OK | |
| 6.CHECK FOR SPARK AND IGNITION |
![]() |
Perform a spark test.
Remove the ignition coil from the cylinder head.
Install the spark plug to the ignition coil.
Disconnect the 4 fuel injector connectors.
Touch the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check for sparks.
Reconnect the 4 fuel injector connectors.
Install the ignition coil.
|
| ||||
| OK | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the injector assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B16-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B14-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B13-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector) |
Reconnect the injector assembly connector.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM) |
![]() |
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-2 - B32-86 (#10) | Always | Below 1 Ω |
| B15-2 - B32-85 (#20) | Always | Below 1 Ω |
| B14-2 - B32-84 (#30) | Always | Below 1 Ω |
| B13-2 - B32-83 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B16-2 or B32-86 (#10) - Body ground | Always | 10 kΩ or higher |
| B15-2 or B32-85 (#20) - Body ground | Always | 10 kΩ or higher |
| B14-2 or B32-84 (#30) - Body ground | Always | 10 kΩ or higher |
| B13-2 or B32-83 (#40) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Fuel Injector) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the injector connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B32-86 (#10) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| B32-85 (#20) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| B32-84 (#30) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| B32-83 (#40) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 12.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage (Click here).
|
| ||||
| OK | |
| 13.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 14.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 15.INSPECT MASS AIR FLOW METER |
Inspect the mass air flow meter (Click here).
|
| ||||
| OK | |
| 16.ADJUST VALVE TIMING |
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 AND/OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Run the engine at an engine speed of 1000 rpm for 4 minutes 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | B |
|
| ||||
| A | ||
| ||
| 18.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage (Click here).
|
| ||||
| OK | |
| 19.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 20.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 21.INSPECT MASS AIR FLOW METER |
Inspect the mass air flow meter (Click here).
|
| ||||
| OK | |
| 22.ADJUST VALVE TIMING |
| NEXT | |
| 23.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 AND/OR P0304) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Run the engine at an engine speed of 1000 rpm for 4 minutes 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 is output | B |
|
| ||||
| A | ||
| ||
| 24.CHECK SPARK PLUG |
Check the spark plug .
|
| ||||
| OK | |
| 25.CHECK FOR SPARK AND IGNITION (SPARK TEST) |
![]() |
Perform a spark test.
Remove the ignition coil from the cylinder head.
Install the spark plug to the ignition coil.
Disconnect the 4 fuel injector connectors.
Touch the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check for sparks.
Reconnect the 4 fuel injector connectors.
Install the ignition coil.
|
| ||||
| OK | |
| 26.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 27.CHECK INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the injector assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B16-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B14-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B13-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector) |
Reconnect the injector assembly connector.
|
| ||||
| OK | |
| 28.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM) |
![]() |
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-2 - B32-86 (#10) | Always | Below 1 Ω |
| B15-2 - B32-85 (#20) | Always | Below 1 Ω |
| B14-2 - B32-84 (#30) | Always | Below 1 Ω |
| B13-2 - B32-83 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B16-2 or B32-86 (#10) - Body ground | Always | 10 kΩ or higher |
| B15-2 or B32-85 (#20) - Body ground | Always | 10 kΩ or higher |
| B14-2 or B32-84 (#30) - Body ground | Always | 10 kΩ or higher |
| B13-2 or B32-83 (#40) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Fuel Injector) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the injector connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 29.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B32-86 (#10) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| B32-85 (#20) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| B32-84 (#30) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| B32-83 (#40) - B32-46 (E01) | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 30.CHECK FUEL INJECTOR OF MISFIRING CYLINDER |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | ||
| ||
| 31.REPLACE SPARK PLUG WITH NORMAL ONE AND CHECK SPARK OF MISFIRING CYLINDER |
Replace the installed spark plug with a spark plug that functions normally.
Perform a spark test.
Install the spark plug to the ignition coil.
Disconnect the 4 fuel injector connectors.
Touch the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check for sparks.
|
| ||||
| OK | ||
| ||
| 32.REPLACE IGNITION COIL WITH NORMAL ONE AND CHECK SPARK OF MISFIRING CYLINDER |
Replace the ignition coil with an ignition coil that functions normally.
Perform a spark test.
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the 4 fuel injector connectors.
Touch the spark plug assembly to the cylinder head.
Crank the engine for less than 2 seconds and check for sparks.
|
| ||||
| OK | ||
| ||
| 33.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B32-46 (E01) - Body ground | Always | Below 1 Ω |
| B32-45 (E02) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 34.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage (Click here).
|
| ||||
| OK | ||
| ||