ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL ENGINE MOUNTING INSULATOR LH |
![]() |
Temporarily install the engine mounting insulator with the 4 bolts.
Tighten the 4 bolts in the sequence shown in the illustration.
Install the wire harness clamp bracket with the bolt.
| 2. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
![]() |
Temporarily install the engine mounting insulator with the 3 bolts.
Tighten the 3 bolts in the sequence shown in the illustration.
Install the radiator reservoir bracket with the bolt.
| 3. INSTALL REAR ENGINE MOUNTING INSULATOR |
![]() |
Temporarily install the engine mounting insulator with the 2 bolts and 2 nuts.
Tighten the 2 bolts and 2 nuts in the sequence shown in the illustration.
| 4. INSTALL DRIVE SHAFT BEARING BRACKET |
![]() |
Install the drive shaft bearing bracket with the 3 bolts.
| 5. INSTALL ENGINE HANGER |
![]() |
Disconnect the air fuel ratio sensor connector and remove the bolt and air fuel ratio sensor bracket.
![]() |
Install the No. 1 and No. 2 engine hangers with 2 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-37021 |
| No. 2 Engine Hanger | 12282-37011 |
| Bolt | 91552-81050 |
Attach an engine sling device and hang the engine with a chain block.
| 6. REMOVE ENGINE STAND |
Attach an engine sling device and hang the engine with a chain block.
Lift the engine and remove it from the engine stand.
| 7. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle) |
![]() |
Temporarily install the clutch release cylinder to bleeder tube to a new clutch release with bearing cylinder assembly.
Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.
![]() |
Install the clutch release with bearing cylinder assembly with 3 new bolts.
![]() |
Install the clutch tube boot to the manual transaxle assembly.
![]() |
Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.
Temporarily install the clutch release bleeder sub-assembly with the 2 bolts.
![]() |
Using a union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release with bearing cylinder assembly.
![]() |
Apply clutch spline grease to the input shaft spline.
| *1 | Clutch Spline Grease |
| 8. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Separate the clutch release cylinder to bleeder tube from the clutch release bleeder sub-assembly.
Remove the 2 bolts and clutch release bleeder sub-assembly.
| 9. INSPECT CLUTCH PIPE LINE (for Manual Transaxle) |
![]() |
Using SST, apply a pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.
| 10. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.
Install the clutch release bleeder sub-assembly with the 2 bolts.
Using a union nut wrench, install the clutch release cylinder to bleeder tube.
| 11. INSTALL CLUTCH ORIFICE ASSEMBLY (for Manual Transaxle) |
![]() |
Install the clutch orifice assembly with the 2 bolts.
| 12. INSTALL CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE (for Manual Transaxle) |
![]() |
Using a union nut wrench, install the clutch release cylinder to accumulator tube.
| 13. INSTALL ORIFICE TO FLEXIBLE HOSE TUBE (for Manual Transaxle) |
![]() |
Temporarily tighten the orifice to flexible hose tube onto the clutch orifice assembly.
Install the orifice to flexible hose tube with the bolt.
Using a union nut wrench, install the orifice to flexible hose tube.
| 14. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Using SST, hold the crankshaft.
![]() |
Clean the bolts and bolt holes.
Apply adhesive to 2 or 3 threads at the end of the 8 bolts.
| *1 | Adhesive |
![]() |
Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.
![]() |
Mark the top of the bolts with paint.
Retighten the 8 bolts an additional 90° in the same sequence.
Check that the paint marks are now at a 90° angle to the top.
| 15. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle) |
![]() |
Insert SST into the clutch disc assembly, and then attach them both to the flywheel sub-assembly.
| 16. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle) |
![]() |
| *1 | Matchmark |
| *2 | Temporarily Install |
Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.
Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.
| 17. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle) |
![]() |
Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.
| 18. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT) |
![]() |
Using SST, hold the crankshaft.
![]() |
Install the front spacer, drive plate and rear spacer onto the crankshaft.
![]() |
Clean the bolts and bolt holes.
Apply adhesive to 2 or 3 threads at the end of the 8 bolts.
| *1 | Adhesive |
![]() |
Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.
| 19. INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle) |
for 2WD:
Install the manual transaxle assembly (Click here).
for 4WD:
Install the manual transaxle assembly (Click here).
| 20. INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT) |
Install the continuously variable transaxle assembly (Click here).
| 21. INSTALL FLYWHEEL HOUSING SIDE COVER |
![]() |
Install the flywheel housing side cover to the cylinder block.
| 22. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter with the 2 bolts.
Connect the starter connector.
Connect starter wire with the nut.
Connect the terminal cap.
| 23. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Install the suspension crossmember to the engine with the bolt.
| *1 | Alignment Mark |
| *2 | Protrusion |
| 24. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
Install the steering column hole cover to the steering gear with a new clamp.
| 25. INSTALL STEERING GEAR HEAT INSULATOR (for RHD) |
Install the heat insulator and bolt to the steering gear.
| 26. INSTALL ENGINE WIRE |
Install the engine wire to the engine.
| 27. INSTALL ENGINE AND TRANSAXLE |
Place the engine on an engine lifter.
![]() |
Remove the 2 bolts and engine hangers.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Operate the engine lifter and install the engine to the vehicle.
![]() |
Temporarily install the front suspension crossmember with the 2 bolts.
Temporarily install the member brace rear RH and LH with the 6 bolts.
![]() |
Install the engine mounting insulator LH with the bolt and nut.
![]() |
Install the engine mounting insulator RH with the bolt and 2 nuts.
![]() |
Tighten the front suspension member bolts.
Tighten the member brace rear bolts.
![]() |
Install the air fuel ratio sensor bracket with the bolt. Then connect the air fuel ratio sensor connector.
| 28. TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR |
![]() |
Temporarily install the engine mounting insulator with the bolt and nut.
| 29. INSTALL FRONT CROSSMEMBER SUB-ASSEMBLY |
![]() |
Install the crossmember with the 6 bolts.
Tighten the bolt and nut holding the engine mounting insulator.
| 30. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH |
![]() |
Install the reinforcement with the 4 bolts.
| 31. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH |
![]() |
Install the reinforcement with the 4 bolts.
| 32. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT) |
![]() |
Apply a few drops of adhesive to 2 or 3 threads of the tips of the 6 torque converter setting bolts.
| *1 | Adhesive |
![]() |
Turn the crankshaft to gain access to the installation locations of the 6 torque converter setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
Install the flywheel housing under cover.
| 33. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD) |
Install the propeller shaft assembly (Click here).
| 34. CONNECT HEATED OXYGEN SENSOR (for 4WD) |
Rotate the sensor counterclockwise the same number of times as recorded in the removal procedure, and then connect it to the front exhaust pipe by hand.
![]() |
Using SST, tighten the sensor.
Connect the grommet to the floor panel.
| 35. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
![]() |
Install a new gasket by hand so that its surface is flush with the exhaust manifold.
![]() |
Install the front exhaust pipe and 2 compression springs with the 2 bolts.
Install a new gasket to the front exhaust pipe.
![]() |
Connect the front exhaust pipe to the center exhaust pipe with the 2 bolts.
| 36. INSTALL DRIVE SHAFT |
for 2WD:
Install the front drive shafts (Click here).
for 4WD:
Install the front drive shafts (Click here).
| 37. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH |
Install the front axle hub sub-assembly (Click here).
| 38. INSTALL FRONT AXLE HUB SUB-ASSEMBLY RH |
| 39. INSTALL FRONT AXLE SHAFT NUT LH |
Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.
Install a new shaft nut.
![]() |
Using a chisel and hammer, stake the shaft nut.
| 40. INSTALL FRONT AXLE SHAFT NUT RH |
| 41. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Attach clip B to the body portion and connect the No. 1 steering column hole cover to the body portion with clip A.
| 42. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks and install the No. 2 steering intermediate shaft to the steering intermediate shaft.
| 43. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() |
Install the silencer sheet with the 2 clips.
Install the floor carpet.
| 44. CONNECT CLUTCH TUBE (for Manual Transaxle) |
![]() |
Connect the clutch hose and install the clip to the clutch hose.
Using a 10 mm union nut wrench, connect the clutch hose to the flexible hose tube while holding the flexible hose.
| 45. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT) |
![]() |
Connect the clamp of the control cable with the bolt.
![]() |
Connect the transmission control cable to the control cable support.
![]() |
Connect the transmission control cable to the bracket with a new clip.
Connect the transmission control cable to the control shaft lever with the nut.
| 46. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle) |
![]() |
Connect the control cable to the control cable bracket, and install 2 new clips.
![]() |
Connect the control cable to the transaxle, and install the 2 washers and 2 clips.
| 47. CONNECT WIRE HARNESS AND HOSE |
![]() |
Connect the heater hoses.
![]() |
Connect the connector tube hose.
![]() |
Install the ground wire with the bolt and clamp.
![]() |
Connect the engine wire and install the nut.
Connect the 3 relay block connectors.
![]() |
Connect the engine wire with the 2 clamps and install the bolt.
| 48. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push the tube connector onto the pipe until the tube connector makes a "click" sound.
![]() |
Install the No. 1 fuel pipe clamp.
| *1 | No. 1 Fuel Pipe Clamp |
| 49. CONNECT NO. 1 RADIATOR HOSE |
![]() |
Connect the radiator hose to the cylinder head.
| 50. INSTALL ECM |
![]() |
Install the 2 brackets to the ECM with the 4 screws.
![]() |
Connect the 2 ECM connectors.
Connect the 2 ECM connectors and lower the 2 levers.
![]() |
Install the ECM with the 3 bolts.
| 51. INSTALL AIR CLEANER CASE |
![]() |
Install the air cleaner case with the 3 bolts.
Attach the wire harness clamp to the air cleaner case.
| 52. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Insert the hinge part of the air cleaner cap and hose into the air cleaner case, and then fasten the 2 hook clamps.
![]() |
Connect the No. 1 air cleaner hose to the throttle body and push apart the tabs of the No. 1 air cleaner hose clamp.
Connect the No. 2 ventilation hose to the cylinder head cover.
![]() |
Attach the clamp.
Connect the mass air flow meter connector.
| 53. INSTALL BATTERY BRACKET REINFORCEMENT |
![]() |
Install the battery bracket reinforcement with the 2 bolts.
| 54. INSTALL FRONT BATTERY BRACKET |
![]() |
Install the front battery bracket with the 3 bolts.
Connect the No. 3 engine wire with the bolt.
Attach the 3 wire harness clamps.
| 55. INSTALL BATTERY TRAY |
| 56. INSTALL BATTERY |
| 57. INSTALL BATTERY CLAMP SUB-ASSEMBLY |
![]() |
Attach the hook of the battery clamp to the front battery bracket.
Partially tighten the nut and temporarily install the bolt.
Adjust the battery clamp position.
Tighten the nut and bolt.
| 58. CONNECT COMPRESSOR WITH PULLEY ASSEMBLY (w/ Air Conditioning System) |
![]() |
Connect the compressor with pulley assembly with the 2 stud bolts.
![]() |
Install the 2 bolts and 2 nuts.
![]() |
Connect the connector.
| 59. CONNECT NO. 2 RADIATOR HOSE |
![]() |
Align the paint mark of the radiator hose with the triangle mark of the water inlet and connect the radiator hose to the water inlet.
| *1 | Paint Mark |
| *2 | Triangle Mark |
| 60. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the wire harness clamp bracket with the bolt.
![]() |
Temporarily install the generator with the bolt.
![]() |
Temporarily install the adjusting bar with the 2 bolts.
![]() |
Install the wire harness to terminal B with the nut.
Install the terminal cap.
Connect the connector and wire harness clamp.
Install V-ribbed belt .
Adjust V-ribbed belt .
Inspect V-ribbed belt .
![]() |
Tighten the bolt.
| 61. INSTALL V-RIBBED BELT |
Temporarily install the V-ribbed belt.
| 62. ADJUST V-RIBBED BELT |
![]() |
Turn bolt C to adjust the tension of the V-ribbed belt.
Tighten bolts A and B.
| 63. CONNECT RADIATOR RESERVOIR ASSEMBLY |
![]() |
Connect the radiator reservoir with the 2 bolts.
Connect the No. 1 and No. 2 water by-pass hoses.
| 64. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 65. ADD TRANSFER OIL (for 4WD) |
Remove the case plug (for filler) and gasket.
Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the case plug (for filler) hole.
Wait approximately 5 minutes and check that the oil level has not changed.
Install a new gasket and the case plug (for filler).
| 66. ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT) |
Add continuously variable transaxle fluid (Click here).
| 67. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle) |
![]() |
Add oil until the oil level is within 5 mm (0.197 in.) from the bottom of the transmission filler plug opening.
Install a new gasket and the transmission filler plug.
| 68. ADD ENGINE OIL |
Clean and install the oil pan drain plug together with a new gasket.
Add new engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL or SM multigrade engine oil |
|
| API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil |
|
| Item | Specified Condition |
| Drain and refill without oil filter change | 3.9 liters (4.1 US qts, 3.4 Imp. qts) |
| Drain and refill with oil filter change | 4.2 liters (4.4 US qts, 3.7 Imp. qts) |
| Dry fill | 4.7 liters (5.0 US qts, 4.1 Imp. qts) |
Install the oil filler cap.
| 69. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
![]() |
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening until it is filled to the B line at the base of the reservoir filler neck.
| Item | Specified Condition |
| for Manual Transaxle | 5.8 liters (6.1 US qts, 5.1 Imp. qts) |
| for CVT | 6.0 liters (6.3 US qts, 5.3 Imp. qts) |
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Condition |
| Manual Air Conditioning System | Fan speed: Any setting except off Temperature: Toward WARM Air conditioning switch: Off |
| Automatic Air Conditioning System | Temperature: Toward MAX (HOT) Air conditioning switch: Off |
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 70. INSPECT SHIFT LEVER POSITION (for CVT) |
When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.
Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves in reverse after moving the shift lever to R.
If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.
| 71. INSPECT FOR FUEL LEAK |
Make sure that there are no fuel leaks after performing maintenance on the fuel system.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON, and push the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no leaks from the fuel system.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
| 72. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 73. INSPECT FOR COOLANT LEAK |
Remove the radiator reservoir cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator reservoir cap.
| 74. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using an intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
When not using the intelligent tester:
Remove the No. 2 cylinder head cover.
![]() |
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
Start the engine and idle it.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | Front view of DLC3 |
![]() |
Using the timing light, check the ignition timing.
Remove SST from the DLC3.
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover.
| 75. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Item | Specified Condition |
| for Manual Transaxle | 580 to 680 rpm |
| for CVT | 600 to 700 rpm |
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
![]() |
When not using the intelligent tester:
| *1 | Front view of DLC3 |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
Check the idle speed.
| Item | Specified Condition |
| for Manual Transaxle | 580 to 680 rpm |
| for CVT | 600 to 700 rpm |
Disconnect the tachometer probe from the DLC3.
| 76. INSPECT CO/HC |
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration during idling and when the engine is running at 2500 rpm.
Check the air fuel ratio sensor and heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|
| 77. INSTALL FRONT WHEEL |
| 78. ADJUST WHEEL ALIGNMENT |
Adjust the front wheel alignment (Click here).
| 79. INSTALL FRONT FLOOR COVER |
![]() |
Install the floor under cover with the 3 clips, bolt and nut.
| 80. INSTALL NO. 2 ENGINE UNDER COVER |
![]() |
Install the under cover with the 3 clips.
| 81. INSTALL REAR ENGINE UNDER COVER RH |
![]() |
Install the under cover with the 3 clips.
| 82. INSTALL REAR ENGINE UNDER COVER LH |
![]() |
Install the under cover with the 2 clips.
| 83. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the under cover with the 6 screws and 10 clips.
| 84. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Attach the 4 clips to install the cover.
| 85. INSTALL RADIATOR SUPPORT OPENING COVER |
Install the radiator support opening cover with the 9 clips.
| 86. RESET MEMORY |
When replacing the engine assembly, perform the Reset Memory procedure (CVT initialization) for K111 (Click here).