Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER
RM30B0U _52 Drivetrain _009469 AXLE AND DIFFERENTIAL _0051195 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

a.

Temporarily install the rear axle carrier to the rear upper control arm with the bolt and nut.


Hide 2.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear lower coil spring insulator to the rear No. 2 suspension arm.


b.
C276119
3.01,0.427 3.24,0.583 0.229,0.156 10 *a
*a 10 mm or less


Install the rear upper coil spring insulator to the rear coil spring.

NOTICE:

Install the rear upper coil insulator so that the distance between the stopper and upper end of the rear coil spring is 10 mm (0.394 in.) or less.



c.
C266194
0.802,2.438 1.354,1.781 false 0.813,2.438 1.354,3.135 false 0.646,2.365 0.958,2.521 0.313,0.156 10 *a
*a Identification Mark


Install the rear coil spring to the rear No. 2 suspension arm.

NOTICE:

Make sure that the identification mark is positioned towards the outer sides of the vehicle.



d.
C266199

Using a jack and wooden block, raise the vehicle gradually to install the rear No. 2 suspension arm to the rear axle carrier. Then temporarily install the bolt.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.

·

Make sure to perform this operation with the vehicle kept as low as possible.




Hide 3.INSTALL REAR TRAILING ARM ASSEMBLY

a.

Install the rear trailing arm to the axle carrier with the 2 bolts.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 4.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 1 suspension arm to the rear axle carrier with a new nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 5.INSTALL REAR SHOCK ABSORBER BRACKET LH

a.

Install the rear shock absorber bracket to the rear axle carrier with the 2 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 7.TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Tighten the bolt.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



Hide 8.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Tighten the bolts of the suspension arm.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


Hide 9.CONNECT PARKING BRAKE ASSEMBLY

a.

Connect the parking brake assembly to the rear axle carrier with the nut.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 10.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 3 parking brake cable to the rear trailing arm with the bolt.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 11.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 12.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)

Hide 13.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for AWD)

Hide 14.TEMPORARILY INSTALL REAR AXLE SHAFT NUT LH (for AWD)

Hide 15.INSPECT REAR AXLE HUB BEARING LOOSENESS

Hide 17.INSTALL REAR DISC

Hide 18.CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 19.CONNECT SKID CONTROL SENSOR WIRE LH (for 2WD)

Hide 20.CONNECT REAR SPEED SENSOR LH (for AWD)

Hide 21.STAKE REAR AXLE SHAFT NUT LH (for AWD)

Hide 22.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 23.INSPECT AND ADJUST PARKING BRAKE

Hide 24.INSPECT AND ADJUST REAR WHEEL ALIGNMENT