Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0058072 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1337/91  Diameter of the Tire is not Uniform  


DESCRIPTION

The 4WD ECU assembly outputs this DTC if a difference in tire size is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1337/91 Diameter of the Tire is not Uniform When the following continues for 36 seconds or more:
At a vehicle speed of 30 km/h (18.6 mph) or more, the average speed difference between the front wheel and rear wheel is 4% or more.
·

Tire size or pressure (front and rear tires)

·

Speed sensor circuit

·

Front speed sensor

·

Rear speed sensor

·

Front speed sensor rotor (Front axle hub sub-assembly)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly)

·

Harness and connector

·

Skid control ECU (Brake actuator assembly)

·

4WD ECU assembly



WIRING DIAGRAM

C284324
3.677,0.406 3.979,0.594 0.302,0.188 10 false FR+ 3.698,0.771 4.01,0.969 0.313,0.198 10 false FR- 4.063,0.292 4.198,0.49 0.135,0.198 10 false 7 4.063,0.708 4.219,0.906 0.156,0.198 10 false 6 5.5,0.281 5.656,0.479 0.156,0.198 10 false 1 5.5,0.688 5.656,0.885 0.156,0.198 10 false 2 5.688,0.396 6.146,0.594 0.458,0.198 10 false FR+ 5.656,0.771 6.115,0.969 0.458,0.198 10 false FR- 5.24,1.01 5.698,1.208 0.458,0.198 10 false A43 5.25,1.177 6.813,1.427 1.563,0.25 10 false Front Speed Sensor RH 3.698,1.729 3.99,1.906 0.292,0.177 10 false FL+ 3.75,2.083 3.99,2.302 0.24,0.219 10 false FL- 4.052,1.635 4.365,1.833 0.313,0.198 10 false 19 4.052,2.021 4.365,2.219 0.313,0.198 10 false 18 5.5,1.625 5.656,1.823 0.156,0.198 10 false 1 5.677,1.74 6.135,1.938 0.458,0.198 10 false FL+ 5.677,2.052 5.99,2.25 0.313,0.198 10 false FL- 5.5,2 5.656,2.198 0.156,0.198 10 false 2 5.25,2.313 5.625,2.521 0.375,0.208 10 false A14 5.271,2.5 6.76,2.719 1.49,0.219 10 false Front Speed Sensor LH 3.635,3.042 3.969,3.229 0.333,0.188 10 false RR+ 4.052,2.938 4.365,3.135 0.313,0.198 10 false 17 3.656,3.396 3.969,3.594 0.313,0.198 10 false RR- 4.063,3.313 4.375,3.51 0.313,0.198 10 false 16 5.49,2.938 5.646,3.135 0.156,0.198 10 false 1 5.49,3.323 5.646,3.521 0.156,0.198 10 false 2 5.698,3.042 6.156,3.24 0.458,0.198 10 false RR+ 5.688,3.375 6,3.573 0.313,0.198 10 false RR- 5.229,3.604 5.573,3.792 0.344,0.188 10 false M20 5.25,3.771 6.688,3.958 1.438,0.188 10 false Rear Speed Sensor RH 3.667,4.292 3.979,4.49 0.313,0.198 10 false RL+ 3.719,4.688 4.031,4.885 0.313,0.198 10 false RL- 4.073,4.188 4.24,4.354 0.167,0.167 10 false 5 4.052,4.594 4.208,4.792 0.156,0.198 10 false 4 5.49,4.188 5.646,4.385 0.156,0.198 10 false 1 5.5,4.583 5.656,4.781 0.156,0.198 10 false 2 5.688,4.292 6.146,4.49 0.458,0.198 10 false RL+ 5.719,4.656 6.177,4.854 0.458,0.198 10 false RL- 5.26,4.896 5.573,5.104 0.313,0.208 10 false N11 5.26,5.094 6.698,5.281 1.438,0.188 10 false Rear Speed Sensor LH 0.365,6.75 1.75,6.948 1.385,0.198 10 false 4WD ECU Assembly 2.646,6.875 3.104,7.073 0.458,0.198 10 false A64 2.656,7.073 4.177,7.448 1.521,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 3.094,7.781 4.844,8.177 1.75,0.396 10 false Acceleration Sensor (Airbag Sensor Assembly) 0.771,8.385 2.469,8.583 1.698,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK TIRE CONDITION
a.

Check the size and condition of all 4 tires.

HINT:

This DTC is output when tire deformation or a difference in tire size is detected.


OK:

The diameter and air pressure of all 4 tires are the same.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

REPLACE PERFORM AIR PRESSURE ADJUSTMENT OR REPLACE TIRES SO THAT ALL 4 TIRES ARE SAME IN SIZE

2.CHECK FOR DTC
a.

Clear the DTCs.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more so that the same DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR


Chassis > Four Wheel Drive > Trouble Codes
50001 118
d.

Check if the speed sensor DTC (brake control system DTC) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR


Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
e.

Read the DTCs using the Techstream.

Result:
Result Proceed to
Only "C1377/91" is output A
DTC is not output B
Speed sensor DTC (brake control system DTC) is output C




A

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR - BRAKE ACTUATOR ASSEMBLY)

B

C

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Turn the power switch off.


c.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the A14, A43, M20 and/or N11 speed sensor connector(s).


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Front RH:
Tester Connection Condition Specified Condition
A64-7 (FR+) - A43-1 (FR+) Always Below 1 Ω
A64-7 (FR+) or A43-1 (FR+) - Body ground Always 10 kΩ or higher
A64-6 (FR-) - A43-2 (FR-) Always Below 1 Ω
A64-6 (FR-) or A43-2 (FR-) - Body ground Always 10 kΩ or higher

for Front LH:
Tester Connection Condition Specified Condition
A64-19 (FL+) - A14-1 (FL+) Always Below 1 Ω
A64-19 (FL+) or A14-1 (FL+) - Body ground Always 10 kΩ or higher
A64-18 (FL-) - A14-2 (FL-) Always Below 1 Ω
A64-18 (FL-) or A14-2 (FL-) - Body ground Always 10 kΩ or higher

for Rear RH:
Tester Connection Condition Specified Condition
A64-17 (RR+) - M20-1 (RR+) Always Below 1 Ω
A64-17 (RR+) or M20-1 (RR+) - Body ground Always 10 kΩ or higher
A64-16 (RR-) - M20-2 (RR-) Always Below 1 Ω
A64-16 (RR-) or M20-2 (RR-) - Body ground Always 10 kΩ or higher

for Rear LH:
Tester Connection Condition Specified Condition
A64-5 (RL+) - N11-1 (RL+) Always Below 1 Ω
A64-5 (RL+) or N11-1 (RL+) - Body ground Always 10 kΩ or higher
A64-4 (RL-) - N11-2 (RL-) Always Below 1 Ω
A64-4 (RL-) or N11-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.PERFORM TEST MODE (SIGNAL CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRAC > Utility
Tester Display
Signal Check
50005 105 1003
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

6.CHECK SPEED SENSOR ROTOR
5.RECONFIRM DTC
a.

Clear the DTCs.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118

Result:
Proceed to
DTC is output
DTC is not output



DTC is output

DTC is not output

6.CHECK SPEED SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Remove the front speed sensor rotor (front axle hub sub-assembly) or rear speed sensor rotor (rear axle hub and bearing assembly).

For front: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL

For rear: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


c.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.




Result:
Proceed to
OK
NG



OK

7.REPLACE SPEED SENSOR

NG

CLEAN OR REPLACE SPEED SENSOR ROTOR

7.REPLACE SPEED SENSOR
a.

Turn the ignition switch off.


b.

NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


Result:
Proceed to
NEXT



NEXT

8.RECONFIRM DTC
8.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Proceed to
DTC is output
DTC is not output


HINT:

Reinstall the sensor, connectors, etc. and restore the vehicle to its prior condition before rechecking DTCs.




DTC is output

9.REPLACE BRAKE ACTUATOR ASSEMBLY

DTC is not output

END

9.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

DTC is not output

END