Faults and Symptoms of Common Rail Diesel Components
Engine Control
| Symptom and Corresponding Main Fault | ·
Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct ·
Black smoke (no lack of power) due to leakage between the turbo and intake manifold |
| Data List | MAP |
| Main fault | Glow system malfunction |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Data List | Check the glow plug indicator light |
| Diagnostic Point | Measure the resistance of the glow plug assembly |
| Main fault | Loss of compression |
| Symptoms | Rough idle (lack of power always) |
| Data List | Engine Speed of Cyl
·
When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Val ·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. |
Common Rail (ALL)
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·
Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)). ·
If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPa, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored. |
| Main fault | Blockage, increase in fuel injection volume |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Val
·
When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute. |
When the sliding resistance of the internal parts of the injector assemblies (i.e. armature shaft, command piston and plunger) has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector assembly closure.
When black smoke occurs due to contamination of the injector assemblies, there are usually other symptoms, such as engine knocking noise at cold idling, rough idling, difficulty starting, etc. which are also present when the common rail pressure is low.
| Main fault | Circuit fault: The injector assembly does not open. |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Same as injector assembly |
| Diagnostic Trouble Code | When the injector driver (EDU) has a fault, some DTCs may be stored. |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Fuel Press, Target Common Rail Pressure
·
Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure). |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel EGR
| Main fault | ·
Does not move smoothly ·
Does not close completely |
| Symptoms | ·
Rough idle ·
EGR valve stuck closed: A loud turbocharger sound. ·
EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt). |
| Data List | Actual EGR Valve Pos., Target EGR Position
·
Generally, Actual EGR Valve Pos. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%). ·
Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs). ·
EGR valve is fully closed when the ignition switch is turned to ON (engine stopped). ·
EGR valve opens to the halfway point at idling after the engine is warmed up. EGR Close Lrn. Val., EGR Close Lrn. Status ·
When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V. ·
In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close. |
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms | ·
Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed. ·
Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur. |
| Data List | Actual Throttle Position
·
0%: Fully open ·
100%: Fully closed ·
When the ignition switch ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily. |
Data List Related to Starting Trouble
Engine Speed
MAP
MAF
Intake Air
Coolant Temp
Engine Speed of Cyl #1 (to #4)
Target Common Rail Pressure
Fuel Press
Target Pump SCV Current
Injection Feedback Val #1 (to #4)
Injection Volume
Actual Throttle Position
Target EGR Position
Actual EGR Valve Pos.
EGR Close Lrn. Status
EGR Close Lrn. Val.
Refer to DTC P0088.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0088
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing a suction control valve, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.
Explanation of Symptom
| Black Smoke | The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with a larger air fuel ratio across the entire operating range. An insufficient quantity of air results in imperfect combustion and increased particulate (soot) emissions.
When the accelerator pedal is depressed, a large amount of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by mass air flow). Black smoke is emitted when either 1) a lack of oxygen is present during combustion, or 2) Too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich. |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Proceed to |
|---|
| DTCs are not output |
| Engine related DTCs are output |
If only DTC P1609 is output, proceed to step 2.
DTCs are not output
Engine related DTCs are output
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DIAGNOSTIC TROUBLE CODE CHART
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the above procedure [A] 10 times or more [B].
Check for black smoke emission during procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
If the procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the racing procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT
Even though it has been determined that the DPF catalytic converter (exhaust manifold converter sub-assembly) needs to be replaced, make sure to complete diagnosis for this problem before replacing it.
Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(for DPF)>REMOVAL
This problem is occurred because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.
| Proceed to |
|---|
| NEXT |
NEXT
Check for air leakage and blockage between the air cleaner case sub-assembly and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
Make sure that the air cleaner filter element sub-assembly is not clogged and the intake and exhaust system hoses are not disconnected.
When the vacuum hoses are disconnected.
Check that the intercooler is not clogged with foreign matter.
Check that there are no disconnected, pinched or leaking hoses or pipes.
Check that there are no modifications made by the user.
No leakage or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wire harness and connector connections of common rail system components.
The wire harnesses and connectors are connected securely.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the injector compensation codes.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
Compensation codes stored in the ECM match the compensation codes of the installed injector assemblies.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the pilot quantity learning (detail).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the above procedure [A] 10 times [B].
Check for black smoke emission during procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP and MAF.
| Tester Display |
|---|
| MAF |
| MAP |
Take a snapshot when the engine speed is maintained at 4000 rpm with no load.
Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.
| Result | Proceed to |
|---|---|
| MAF 85 gm/s or more and MAP 120 kPa or higher | A |
| Except above | B |
The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
A
B
Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute.
| Result | Proceed to |
|---|---|
| Injection Volume is less than 5 mm3/st at 4000 rpm | A |
| Injection Feedback Val for at least one cylinder is more than 3 mm3/st | B |
| Except above | C |
A
B
C
Replace the injector assemblies.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Use this Active Test to help determine whether a cylinder has compression loss or not.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Compression / Engine Speed of Cyl #1 to #4.
| Active Test Display |
|---|
| Check the Cylinder Compression |
| Data List Display |
|---|
| Engine Speed of Cyl #1 |
| Engine Speed of Cyl #2 |
| Engine Speed of Cyl #3 |
| Engine Speed of Cyl #4 |
Check the engine speed during the Active Test.
| Result | Proceed to |
|---|---|
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other | B |
When cranking, if the speed of a cylinder is approximately 100 rpm higher than the other cylinders, there is probably a complete loss of compression in that cylinder.
A
B
Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel filter element assembly.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL FILTER>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation codes.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
Perform the pilot quantity learning.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the above procedure [A] 10 times [B].
Check for black smoke emission during procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP and Atmosphere Pressure.
| Tester Display |
|---|
| Atmosphere Pressure |
| MAP |
Compare MAP to Atmosphere Pressure when the ignition switch ON (engine stopped).
If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa (0.1 kgf/cm2, 1.5 psi) or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather (high atmospheric pressure, low atmospheric pressure).
| Result | Proceed |
|---|---|
| MAP and Atmosphere Pressure have same value | A |
| Atmosphere Pressure is different from actual atmospheric pressure | B |
| MAP is different from actual atmospheric pressure | C |
A
B
C
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / All Data / Fuel Press, Target Common Rail Pressure.
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).
"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
"Fuel Press" is the actual fuel pressure in common rail assembly.
When the pressure discharge valve on the common rail assembly has a malfunction, the actual fuel pressure changes as shown by "Pressure Discharge Valve Abnormal Fuel Press" in the illustration.
The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.
There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Fuel Press and Common Rail Press Sens 2 exceeds 10000 kPa (102 kgf/cm2, 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the fuel pressure sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Soak the engine for a long time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Coolant Temp is the same as the ambient temperature.
When the engine coolant temperature is low even though the engine has been fully warmed up, or when the engine coolant temperature is high even though the engine is cold, inspect the sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Soak the engine for a long time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air and Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air |
| Intake Air Temp (Turbo) |
Intake Air is the same as Intake Air Temp (Turbo).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the mass air flow meter assembly.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION
Inspect the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>INSPECTION
Replace the mass air flow meter assembly.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
It is only necessary to replace the part when the results of the inspection indicate a problem.
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
It is only necessary to replace the part when the results of the inspection indicate a problem.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
Replace the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
It is only necessary to replace the part when the results of the inspection indicate a problem.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B48-1 - B76-41 (PCV+) | Always | Below 1 Ω |
| B48-2 - B76-81 (PCV-) | Always | Below 1 Ω |
| B48-1 or B76-41 (PCV+) - Body ground | Always | 10 kΩ or higher |
| B48-2 or B76-81 (PCV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the inlet hose from the supply pump assembly.
Operate the priming pump and check that fuel is being supplied to the supply pump assembly.
Fuel is properly supplied to the supply pump assembly when the priming pump is operated.
When there is a lack of fuel, the fuel pressure drops.
Inspect for fuel filter element assembly clogging (Check that the fuel filter element assembly is not clogged).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the suction control valve.
Click hereEngine / Hybrid System>2AD-FTV FUEL>SUCTION CONTROL VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform the supply pump initialization.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check and replace the clogged fuel pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat the above procedure [A] 10 times [B].
Check for black smoke emission during procedures [A] and [B].
Black smoke is emitted less than 5 times.
Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close / All Data / MAF.
| Active Test Display |
|---|
| Activate the EGR Valve Close |
| Data List Display |
|---|
| MAF |
Read the MAF value when the EGR valve is closed using the Active Test function.
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close:
OFF (Open) to Close |
MAF value does not change | A |
| MAF value changes | B |
As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter assembly.
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
|---|---|---|
| Open (67%) | ·
Atmosphere pressure: 101 kPa ·
Intake air temperature: 30°C (86°F) ·
Engine coolant temperature: 88°C (190°F) |
3 to 12 gm/s |
| Closed (0%) | 7 gm/s or more |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
With the ignition switch ON and engine stopped, read the value when 30 seconds has elapsed.
| GTS Display | Condition | Standard |
|---|---|---|
| MAF | Ignition switch ON (do not start engine) | 0.35 gm/s or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / All Data / EGR Cooler Bypass Position and MAF.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| MAF |
| EGR Cooler Bypass Position |
Using the Active Test function, switch the No. 1 vacuum switching valve assembly (for EGR cooler) between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the EGR pipe with cooler sub-assembly is clogged, the MAF changes.
A
B
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
When cleaning the electric EGR control valve assembly, perform initialization procedure.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EGR pipe with cooler sub-assembly.
Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>EGR COOLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the mass air flow meter assembly.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT