Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) J

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A275101
0.99,1.146 2.688,1.302 1.698,0.156 10 false from EFI-MAIN NO. 1 Fuse 0.958,1.49 2.938,1.698 1.979,0.208 10 false from EFI-MAIN NO. 1 Relay 3.021,1.021 3.427,1.177 0.406,0.156 10 false BATT 2.844,1.354 3.417,1.563 0.573,0.208 10 false +B, +B2 3.135,2.281 3.375,2.438 0.24,0.156 10 false VC 4.115,3.135 4.292,3.292 0.177,0.156 10 false R 4.406,1.146 6.25,1.292 1.844,0.146 10 false 5 V Constant Voltage Circuit 5.396,1.958 6.417,2.146 1.021,0.188 10 false Microprocessor 4.958,3.365 5.344,3.552 0.385,0.188 10 false ECM 0.229,3.01 2.813,3.344 2.583,0.333 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 0.229,2.167 2.719,2.646 2.49,0.479 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs)

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A299057
0.219,2.76 5.26,2.958 5.042,0.198 10 false Accelerator Pedal Sensor Assembly 0.219,2.604 1.094,2.875 0.875,0.271 10 false A6 0.302,5.25 2.438,5.521 2.135,0.271 10 false Diesel Throttle Body Assembly 0.302,5.083 1.177,5.354 0.875,0.271 10 false B3 0.323,8.073 1.198,8.344 0.875,0.271 10 false B70 0.323,8.26 2.292,8.677 1.969,0.417 10 false Fuel Pressure Sensor (Built into Common Rail Assembly) 3.208,5.313 4.083,5.583 0.875,0.271 10 false Shielded 1.74,0.344 2.615,0.615 0.875,0.271 10 false VPA 1.74,0.74 2.615,1.01 0.875,0.271 10 false EPA 1.646,1.104 2.521,1.375 0.875,0.271 10 false VCPA 1.667,1.479 2.542,1.75 0.875,0.271 10 false VPA2 1.667,1.865 2.542,2.135 0.875,0.271 10 false EPA2 1.677,2.219 2.552,2.49 0.875,0.271 10 false VCP2 2.156,0.229 3.031,0.5 0.875,0.271 10 false 6 2.167,0.604 2.427,0.844 0.26,0.24 10 false 5 2.167,0.979 2.427,1.219 0.26,0.24 10 false 4 2.177,1.344 2.438,1.583 0.26,0.24 10 false 3 2.167,1.729 2.427,1.969 0.26,0.24 10 false 2 2.167,2.094 2.427,2.333 0.26,0.24 10 false 1 5.229,0.146 5.531,0.396 0.302,0.25 10 false 53 5.188,0.365 5.688,0.635 0.5,0.271 10 false A61 5.188,0.719 5.688,0.99 0.5,0.271 10 false A61 5.188,1.104 5.688,1.375 0.5,0.271 10 false A61 5.188,1.469 5.688,1.74 0.5,0.271 10 false A61 5.188,1.844 5.688,2.115 0.5,0.271 10 false A61 5.188,2.219 5.688,2.49 0.5,0.271 10 false A61 5.25,0.552 5.552,0.802 0.302,0.25 10 false 56 5.25,0.927 5.552,1.177 0.302,0.25 10 false 55 5.25,1.302 5.552,1.552 0.302,0.25 10 false 54 5.24,1.667 5.542,1.917 0.302,0.25 10 false 58 5.25,2.031 5.552,2.281 0.302,0.25 10 false 57 5.573,0.365 6.448,0.635 0.875,0.271 10 false VPA 5.583,0.719 6.458,0.99 0.875,0.271 10 false EPA 5.594,1.094 6.469,1.365 0.875,0.271 10 false VCPA 5.594,1.458 6.469,1.729 0.875,0.271 10 false VPA2 5.594,1.823 6.469,2.094 0.875,0.271 10 false EPA2 5.604,2.198 6.479,2.469 0.875,0.271 10 false VCP2 5.188,3.281 5.688,3.552 0.5,0.271 10 false B76 5.188,3.646 5.688,3.917 0.5,0.271 10 false B76 5.198,4.021 5.698,4.292 0.5,0.271 10 false B76 5.198,4.396 5.698,4.667 0.5,0.271 10 false B76 5.198,4.76 5.698,5.031 0.5,0.271 10 false B76 5.177,5.156 5.677,5.427 0.5,0.271 10 false B76 5.188,5.771 5.688,6.042 0.5,0.271 10 false B76 5.188,6.146 5.688,6.417 0.5,0.271 10 false B76 5.188,6.521 5.688,6.792 0.5,0.271 10 false B76 5.188,6.896 5.688,7.167 0.5,0.271 10 false B76 5.188,7.26 5.688,7.531 0.5,0.271 10 false B76 5.177,7.625 5.677,7.896 0.5,0.271 10 false B76 5.25,3.083 5.552,3.333 0.302,0.25 10 false 97 5.208,3.469 5.51,3.719 0.302,0.25 10 false 119 5.26,3.833 5.563,4.083 0.302,0.25 10 false 96 5.25,4.208 5.552,4.458 0.302,0.25 10 false 42 5.24,4.583 5.542,4.833 0.302,0.25 10 false 43 5.26,4.979 5.563,5.229 0.302,0.25 10 false 82 5.25,5.573 5.552,5.823 0.302,0.25 10 false 66 5.25,5.969 5.552,6.219 0.302,0.25 10 false 67 5.271,6.333 5.573,6.583 0.302,0.25 10 false 68 5.219,6.708 5.521,6.958 0.302,0.25 10 false 114 5.26,7.448 5.563,7.698 0.302,0.25 10 false 69 5.26,7.073 5.563,7.323 0.302,0.25 10 false 91 5.594,3.292 6.469,3.563 0.875,0.271 10 false VCVL 5.594,3.656 6.469,3.927 0.875,0.271 10 false VLU 5.604,4.021 6.479,4.292 0.875,0.271 10 false EVLU 5.594,4.406 6.469,4.677 0.875,0.271 10 false M+ 5.604,4.74 6.479,5.01 0.875,0.271 10 false M- 5.594,5.146 6.469,5.417 0.875,0.271 10 false GE01 5.594,5.781 6.469,6.052 0.875,0.271 10 false PCR1 5.594,6.125 6.469,6.396 0.875,0.271 10 false E2M 5.604,6.521 6.479,6.792 0.875,0.271 10 false VCM 5.594,6.875 6.469,7.146 0.875,0.271 10 false PCR2 5.594,7.26 6.469,7.531 0.875,0.271 10 false E2S 5.604,7.646 6.479,7.917 0.875,0.271 10 false VCS 1.833,4.406 2.708,4.677 0.875,0.271 10 false M+ 1.854,4.76 2.729,5.031 0.875,0.271 10 false M- 1.76,3.667 2.635,3.938 0.875,0.271 10 false VTA 1.823,4.031 2.698,4.302 0.875,0.271 10 false E2 1.844,3.281 2.719,3.552 0.875,0.271 10 false VC 2.177,3.135 2.479,3.385 0.302,0.25 10 false 5 2.177,3.51 3.052,3.781 0.875,0.271 10 false 6 2.177,3.896 2.438,4.135 0.26,0.24 10 false 3 2.177,4.271 2.438,4.51 0.26,0.24 10 false 2 2.177,4.635 2.438,4.875 0.26,0.24 10 false 1 2.167,5.635 2.469,5.885 0.302,0.25 10 false 5 2.167,6.01 2.427,6.25 0.26,0.24 10 false 4 2.167,6.396 3.042,6.667 0.875,0.271 10 false 6 2.177,6.781 2.438,7.021 0.26,0.24 10 false 2 2.167,7.135 2.427,7.375 0.26,0.24 10 false 3 2.167,7.51 2.427,7.75 0.26,0.24 10 false 1 1.813,5.781 2.688,6.052 0.875,0.271 10 false PR 1.844,6.156 2.719,6.427 0.875,0.271 10 false E2 1.833,6.521 2.708,6.792 0.875,0.271 10 false VC 1.771,6.896 2.646,7.167 0.875,0.271 10 false PR2 1.76,7.281 2.635,7.552 0.875,0.271 10 false E2S 1.75,7.635 2.625,7.906 0.875,0.271 10 false VCS 5.938,8.521 6.813,8.792 0.875,0.271 10 false ECM

A213404
5.208,1.906 5.5,2.052 0.292,0.146 10 false B76 5.24,7.656 5.604,7.823 0.365,0.167 10 false ECM 0.375,5.021 0.646,5.208 0.271,0.188 10 false B47 0.375,5.177 2.646,5.333 2.271,0.156 10 false Manifold Absolute Pressure Sensor 1.74,4.219 2.052,4.396 0.313,0.177 10 false PIM 1.771,3.813 2.052,3.958 0.281,0.146 10 false VC 1.896,4.656 2.021,4.802 0.125,0.146 10 false E 2.167,3.708 2.292,3.906 0.125,0.198 10 false 3 2.177,4.135 2.323,4.344 0.146,0.208 10 false 2 2.177,4.563 2.313,4.719 0.135,0.156 10 false 1 5.604,4.219 5.917,4.396 0.313,0.177 10 false PIM 5.646,3.813 6.125,3.958 0.479,0.146 10 false VCPM 5.604,4.646 5.979,4.792 0.375,0.146 10 false EPIM 5.292,3.625 5.5,3.792 0.208,0.167 10 false 93 5.229,4.063 5.51,4.208 0.281,0.146 10 false 117 5.292,4.479 5.49,4.646 0.198,0.167 10 false 72 0.448,2.646 0.896,2.813 0.448,0.167 10 false i1 0.448,2.833 1.875,3 1.427,0.167 10 false EGR Valve Assembly 1.75,0.948 1.969,1.094 0.219,0.146 10 false VC 1.688,1.25 2,1.417 0.313,0.167 10 false VTA 1.781,1.563 2.01,1.719 0.229,0.156 10 false E2 1.75,1.885 1.979,2.052 0.229,0.167 10 false M+ 1.771,2.198 1.969,2.365 0.198,0.167 10 false M- 5.615,0.917 6.073,1.063 0.458,0.146 10 false VCEG 5.615,1.24 6.042,1.406 0.427,0.167 10 false EGLS 5.625,1.563 6.052,1.719 0.427,0.156 10 false EEGL 5.625,1.875 6.063,2.042 0.438,0.167 10 false EGM+ 5.635,2.188 6.063,2.354 0.427,0.167 10 false EGM- 2.156,0.833 2.271,0.979 0.115,0.146 10 false 2 2.167,1.156 2.292,1.292 0.125,0.135 10 false 4 2.167,1.458 2.271,1.615 0.104,0.156 10 false 3 2.167,1.792 2.292,1.969 0.125,0.177 10 false 5 2.177,2.125 2.313,2.271 0.135,0.146 10 false 1 5.271,0.76 5.479,0.927 0.208,0.167 10 false 94 5.198,1.094 5.49,1.25 0.292,0.156 10 false 118 5.26,1.406 5.448,1.563 0.188,0.156 10 false 95 5.271,1.729 5.458,1.885 0.188,0.156 10 false 86 5.271,2.052 5.458,2.219 0.188,0.167 10 false 85 0.469,7.375 0.781,7.531 0.313,0.156 10 false B72 0.469,7.542 1.969,7.698 1.5,0.156 10 false Battery Current Sensor 1.688,5.958 2,6.115 0.313,0.156 10 false THB 1.792,6.292 2,6.469 0.208,0.177 10 false E2 1.823,6.615 1.99,6.771 0.167,0.156 10 false IB 1.667,6.938 1.99,7.104 0.323,0.167 10 false VC5 2.156,5.885 2.271,6.031 0.115,0.146 10 false 1 2.156,6.198 2.26,6.375 0.104,0.177 10 false 4 2.156,6.5 2.271,6.729 0.115,0.229 10 false 3 2.156,6.833 2.26,7.01 0.104,0.177 10 false 2 5.552,5.948 5.854,6.115 0.302,0.167 10 false THB 5.563,6.271 5.833,6.427 0.271,0.156 10 false EIB 5.594,6.604 5.76,6.771 0.167,0.167 10 false IB 5.573,6.927 5.927,7.083 0.354,0.156 10 false VCIB 5.219,5.813 5.49,5.969 0.271,0.156 10 false 115 5.281,6.135 5.49,6.292 0.208,0.156 10 false 77 5.208,6.448 5.49,6.604 0.281,0.156 10 false 116 5.281,6.771 5.479,6.948 0.198,0.177 10 false 75 3.646,2.667 4.24,2.833 0.594,0.167 10 false Shielded 5.208,2.219 5.5,2.365 0.292,0.146 10 false B76 5.198,1.583 5.49,1.729 0.292,0.146 10 false B76 5.208,1.26 5.5,1.406 0.292,0.146 10 false B76 5.208,0.938 5.5,1.083 0.292,0.146 10 false B76 5.208,3.802 5.5,3.948 0.292,0.146 10 false B76 5.208,4.229 5.5,4.375 0.292,0.146 10 false B76 5.208,4.656 5.5,4.802 0.292,0.146 10 false B76 5.208,6.938 5.5,7.083 0.292,0.146 10 false B76 5.219,6.615 5.51,6.76 0.292,0.146 10 false B76 5.219,6.292 5.51,6.438 0.292,0.146 10 false B76 5.219,5.969 5.51,6.115 0.292,0.146 10 false B76

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).


PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

2.CHECK COMMUNICATION BETWEEN GTS AND ECM

MIL illuminates

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

Check the communication between the GTS and ECM.

Result:
Proceed to
Communication is not possible
Communication is possible




Communication is not possible

3.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

Communication is possible

3.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

4.CHECK MIL (DIESEL THROTTLE BODY ASSEMBLY)

MIL illuminates

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

4.CHECK MIL (DIESEL THROTTLE BODY ASSEMBLY)
a.

Disconnect the diesel throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

5.CHECK MIL (FUEL PRESSURE SENSOR)

MIL illuminates

REPLACE DIESEL THROTTLE BODY ASSEMBLY

5.CHECK MIL (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

6.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

MIL illuminates

REPLACE COMMON RAIL ASSEMBLY

6.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Disconnect the electric EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

7.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

MIL illuminates

REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

7.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

8.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY)

MIL illuminates

8.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY)
a.

Disconnect the battery current sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Proceed to
MIL does not illuminate
MIL illuminates




MIL does not illuminate

9.CHECK HARNESS AND CONNECTOR

MIL illuminates

9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the diesel throttle body assembly connector.


c.

Disconnect the fuel pressure sensor connector.


d.

Disconnect the electric EGR control valve assembly connector.


e.

Disconnect the manifold absolute pressure sensor connector.


f.

Disconnect the battery current sensor connector.


g.

Disconnect the ECM connectors.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A61-55 (VCPA) - Body ground Always 10 kΩ or higher
A61-57 (VCP2) - Body ground Always 10 kΩ or higher
B76-97 (VCVL) - Body ground Always 10 kΩ or higher
B76-68 (VCM) - Body ground Always 10 kΩ or higher
B76-69 (VCS) - Body ground Always 10 kΩ or higher
B76-94 (VCEG) - Body ground Always 10 kΩ or higher
B76-93 (VCPM) - Body ground Always 10 kΩ or higher
B76-75 (VCIB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR