Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) J

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the clutch start switch assembly and to terminal STA of the ECM (STA signal).

*1: w/o entry and start system

*2: w/ entry and start system


WIRING DIAGRAM

A284211
0.177,0.135 4.948,0.375 4.771,0.24 12 false w/ Entry and Start System: 0.125,2.427 0.583,2.625 0.458,0.198 10 false G82 0.135,2.635 2.385,3.094 2.25,0.458 10 false Certification ECU (Smart Key ECU Assembly) 4.406,2.406 5.563,3.156 1.156,0.75 10 false Park/Neutral Position Switch Assembly 5.719,1.594 6.333,1.792 0.615,0.198 10 false NSW*1 1.448,1.073 1.833,1.323 0.385,0.25 10 false NE 1.385,2.115 2,2.313 0.615,0.198 10 false STA 5.677,3.688 6.292,3.885 0.615,0.198 10 false STA 6.063,5.01 6.677,5.208 0.615,0.198 10 false ECM 5.698,1.063 6.313,1.26 0.615,0.198 10 false NEO 4.281,2.021 4.74,2.219 0.458,0.198 10 false B36*1 1.26,1.583 1.875,1.781 0.615,0.198 10 false STAR 3.135,1.906 3.594,2.104 0.458,0.198 10 false A4*2 3.146,2.063 3.604,2.26 0.458,0.198 10 false F2*3 3.125,2.292 3.917,3.167 0.792,0.875 10 false Clutch Start Switch Assembly 0.594,4.844 1.438,5.104 0.844,0.26 10 false FL MAIN 0.583,3.813 1.427,4.073 0.844,0.26 10 false ST 2.875,4.573 3.719,4.833 0.844,0.26 10 false ST 0.708,6.823 1.552,7.083 0.844,0.26 10 false Battery 1.5,6.708 2.344,6.969 0.844,0.26 10 false Starter 1.781,5.698 2.625,5.958 0.844,0.26 10 false B6 1.063,5.938 1.906,6.198 0.844,0.26 10 false C4 1.073,5.74 1.917,6 0.844,0.26 10 false 1 1.594,5.688 2.438,5.948 0.844,0.26 10 false 1 2.646,5.073 2.99,5.323 0.344,0.25 10 false 1 2.646,4.115 2.99,4.365 0.344,0.25 10 false 2 2.125,4.115 2.469,4.365 0.344,0.25 10 false 5 2.115,5.052 2.458,5.302 0.344,0.25 10 false 3 2.75,2.073 3.094,2.323 0.344,0.25 10 false 2 2.74,3 3.083,3.25 0.344,0.25 10 false 1 4.063,2.052 4.406,2.302 0.344,0.25 10 false 4 4.042,2.99 4.385,3.24 0.344,0.25 10 false 9 5.344,1.063 5.719,1.323 0.375,0.26 10 false A61 5.354,1.583 5.729,1.844 0.375,0.26 10 false B76 5.354,3.771 5.729,4.031 0.375,0.26 10 false A61 5.365,3.583 5.74,3.844 0.375,0.26 10 false 43 5.385,1.406 5.76,1.667 0.375,0.26 10 false 38 5.396,0.875 5.771,1.135 0.375,0.26 10 false 10 3.063,5.667 5.792,5.906 2.729,0.24 10 false *1: for Automatic Transaxle 3.052,6.052 5.781,6.292 2.729,0.24 10 false *2: for LHD with Manual Transaxle 3.063,6.417 5.792,6.656 2.729,0.24 10 false *3: for RHD with Manual Transaxle 1.771,0.958 2.146,1.219 0.375,0.26 10 false 16 1.802,1.49 2.177,1.75 0.375,0.26 10 false 5 1.792,1.979 2.167,2.24 0.375,0.26 10 false 7 4.01,2.313 4.469,2.51 0.458,0.198 10 false B 4.021,2.771 4.479,2.969 0.458,0.198 10 false L

A284212
4.281,2.177 5.302,2.958 1.021,0.781 10 false Park/Neutral Position Switch Assembly 2.729,2.375 3.75,3.156 1.021,0.781 10 false Clutch Start Switch Assembly 4.313,1.927 4.813,2.125 0.5,0.198 10 false B36*1 2.75,2.115 3.25,2.313 0.5,0.198 10 false F2*3 0.958,1.813 2.021,2.104 1.063,0.292 10 false Ignition Switch 0.979,1.177 1.458,1.583 0.479,0.406 10 false AM2 1.573,1.177 2.052,1.583 0.479,0.406 10 false ST2 0.552,2.198 1.031,2.604 0.479,0.406 10 false AM2 1.156,3.219 1.635,3.625 0.479,0.406 10 false ST 0.573,4.729 1.49,5.01 0.917,0.281 10 false FL MAIN 5.354,3.552 5.833,3.958 0.479,0.406 10 false A61 1.604,6.51 2.521,6.792 0.917,0.281 10 false Starter 0.729,6.615 1.646,6.896 0.917,0.281 10 false Battery 2.052,3.854 2.26,4.115 0.208,0.26 10 false 5 2.052,4.833 2.26,5.094 0.208,0.26 10 false 3 2.604,4.844 2.813,5.104 0.208,0.26 10 false 1 3.896,1.781 4.104,2.042 0.208,0.26 10 false 4 1.771,5.469 2.25,5.875 0.479,0.406 10 false B6 1.073,5.708 1.552,6.115 0.479,0.406 10 false C4 1.104,5.531 1.313,5.792 0.208,0.26 10 false 1 1.563,5.458 1.771,5.719 0.208,0.26 10 false 1 5.354,1.281 5.833,1.688 0.479,0.406 10 false B76 5.385,1.083 5.865,1.49 0.479,0.406 10 false 38 5.385,3.375 5.865,3.781 0.479,0.406 10 false 43 5.708,3.448 6.188,3.854 0.479,0.406 10 false STA 5.667,1.292 6.354,1.698 0.688,0.406 10 false NSW*1 2.76,1.927 3.26,2.125 0.5,0.198 10 false F4*2 3.656,5.167 6.208,5.479 2.552,0.313 10 false *1: for Automatic Transaxle 3.656,5.531 6.208,5.844 2.552,0.313 10 false *2: for LHD with Manual Transaxle 3.667,5.896 6.219,6.208 2.552,0.313 10 false *3: for RHD with Manual Transaxle 2.344,1.792 2.552,2.052 0.208,0.26 10 false 2 2.365,2.792 2.573,3.052 0.208,0.26 10 false 1 3.854,2.781 4.063,3.042 0.208,0.26 10 false 9 0.677,1.604 1.156,2.01 0.479,0.406 10 false G4 0.823,1.146 1.031,1.406 0.208,0.26 10 false 4 1.938,1.135 2.146,1.396 0.208,0.26 10 false 2 2.552,3.875 2.76,4.135 0.208,0.26 10 false 2 0.125,0.115 5.083,0.354 4.958,0.24 12 false w/o Entry and Start System: 3.854,2.052 4.354,2.25 0.5,0.198 10 false B 3.854,2.531 4.354,2.729 0.5,0.198 10 false L

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Proceed to
Engine cannot be cranked
Engine can be cranked




Engine cannot be cranked

2.READ VALUE USING GTS (STARTER SIGNAL)

Engine can be cranked

23.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG (for manual transaxle)
NG (for automatic transaxle)



OK

3.INSPECT ST RELAY

NG (for manual transaxle)

11.INSPECT CLUTCH START SWITCH ASSEMBLY

NG (for automatic transaxle)

17.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE ST RELAY

4.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST relay) - B6-1 Always Below 1 Ω
3 (ST relay) or B6-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STARTER ASSEMBLY)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C4-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
a.
A296486
0.094,0.146 0.406,0.302 0.313,0.156 10 *1 2.073,3.51 2.385,3.667 0.313,0.156 10 *2
*1 Engine Room NO. 2 Relay Block and Junction Block Assembly
*2 ST Relay


Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY)

8.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK (for manual transaxle)
OK (for automatic transaxle)
NG



OK (for manual transaxle)

9.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)

OK (for automatic transaxle)

10.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay) - A4-1*1 Always Below 1 Ω
2 (ST relay) - F2-1*2 Always Below 1 Ω
2 (ST relay) or A4-1*1 - Body ground Always 10 kΩ or higher
2 (ST relay) or F2-1*2 - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay) - B36-9 (L) Always Below 1 Ω
2 (ST relay) or B36-9 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK (w/ entry and start system)
OK (w/o entry and start system)
NG



OK (w/ entry and start system)

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

OK (w/o entry and start system)

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2*1 Always Below 1 Ω
G82-5 (STAR) - F2-2*2 Always Below 1 Ω
G82-5 (STAR) or A4-2*1 - Body ground Always 10 kΩ or higher
G82-5 (STAR) or F2-2*2 - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1*1 - A61-43 (STA) Always Below 1 Ω
F2-1*2 - A61-43 (STA) Always Below 1 Ω
A4-1*1 or A61-43 (STA) - Body ground Always 10 kΩ or higher
F2-1*2 or A61-43 (STA) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

GO TO ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2*1 Always Below 1 Ω
G4-2 (ST2) - F2-2*2 Always Below 1 Ω
G4-2 (ST2) or A4-2*1 - Body ground Always 10 kΩ or higher
G4-2 (ST2) or F2-2*2 - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1*1 - A61-43 (STA) Always Below 1 Ω
F2-1*2 - A61-43 (STA) Always Below 1 Ω
A4-1*1 or A61-43 (STA) - Body ground Always 10 kΩ or higher
F2-1*2 or A61-43 (STA) - Body ground Always 10 kΩ or higher


·

*1: LHD

·

*2: RHD



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK (w/ entry and start system)
OK (w/o entry and start system)
NG



OK (w/ entry and start system)

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

OK (w/o entry and start system)

20.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - B36-4 (B) Always Below 1 Ω
G82-5 (STAR) or B36-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-9 (L) - A61-43 (STA) Always Below 1 Ω
B36-9 (L) or A61-43 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - B36-4 (B) Always Below 1 Ω
G4-2 (ST2) or B36-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room NO. 2 relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-9 (L) - A61-43 (STA) Always Below 1 Ω
B36-9 (L) or A61-43 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)