1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
2.INSTALL ENGINE TO ENGINE STAND
22210
3.REMOVE THROTTLE BODY ASSEMBLY
17361M
4.REMOVE AIR TUBE
5.REMOVE INTAKE MANIFOLD
6.REMOVE WIRE HARNESS CLAMP BRACKET
23901
7.REMOVE FUEL TUBE SUB-ASSEMBLY
23807
8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
23250
9.REMOVE FUEL INJECTOR ASSEMBLY
11452
10.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
17167
11.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17118
12.REMOVE MANIFOLD STAY
17141
13.REMOVE EXHAUST MANIFOLD
29300
14.REMOVE VACUUM PUMP ASSEMBLY
12261
15.REMOVE PCV HOSE
16267
16.DISCONNECT NO. 3 WATER BY-PASS HOSE
16261
17.REMOVE WATER BY-PASS HOSE
16262
18.DISCONNECT WATER INLET HOSE
16321
19.REMOVE WATER INLET
16331A
20.REMOVE THERMOSTAT
19500
21.REMOVE IGNITION COIL ASSEMBLY
12551A
22.REMOVE NO. 1 VACUUM PUMP BRACKET
16620
23.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
11201
24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
11213
25.REMOVE CYLINDER HEAD COVER GASKET
26.SET NO. 1 CYLINDER TO TDC/COMPRESSION
13471
27.REMOVE CRANKSHAFT PULLEY
13540
28.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
15620
29.REMOVE OIL FILTER CAP ASSEMBLY
30.REMOVE ENGINE MOUNTING BRACKET STUD BOLT
11302
31.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 3 bolts and engine mounting bracket RH.
Remove the 4 bolts and oil filter bracket.
Remove the 2 O-rings.
| *1 | Seal Washer |
Remove the 19 bolts and seal washer.
| *a | Protective Tape |
Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver as shown in the illustration.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover sub-assembly.
Tape the screwdriver tip before use.
Remove the 3 O-rings.
Remove the 3 bolts and engine water pump assembly.
Remove the gasket.
11302A
32.REMOVE TIMING CHAIN COVER OIL SEAL
| *1 | Protective Tape |
| *2 | Wooden Block |
Place the timing chain cover sub-assembly on wooden blocks.
Using a screwdriver, tap out the timing chain cover oil seal.
Do not damage the surface of the timing chain cover oil seal press fit hole.
Tape the screwdriver tip before use.
13559
33.REMOVE CHAIN TENSIONER SLIPPER
13561
34.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
35.REMOVE CHAIN SUB-ASSEMBLY
13521
36.REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket.
13507
37.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
Temporarily install the crankshaft pulley and crankshaft pulley bolt.
Using SST, hold the crankshaft. Then remove the drive shaft gear nut.
Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-00850 (quantity: 2)
Remove SST, the crankshaft pulley bolt and the crankshaft pulley.
Remove the bolt, chain tensioner plate and chain damper spring.
| *1 | Oil Pump Drive Gear |
| *2 | Oil Pump Drive Shaft Gear |
| *3 | No. 2 Chain Sub-assembly |
Remove the oil pump drive gear, oil pump drive shaft gear and No. 2 chain sub-assembly.
12102A
38.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 10 bolts and 2 nuts.
Insert the blade of a oil pan seal cutter between the stiffening crankcase and No. 2 oil pan sub-assembly. Cut through the sealer and remove the No. 2 oil pan sub-assembly.
Be careful not to damage the surface of the oil pan which contacts the stiffening crankcase.
Be careful not to damage the stiffening crankcase flange.
15100
39.REMOVE OIL PUMP ASSEMBLY
Remove the 3 bolts and oil pump assembly.