Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0001  Fuel Volume Regulator Control Circuit / Open  


DESCRIPTION

The fuel quantity control valve is installed to the fuel supply pump assembly. The fuel quantity control valve is controlled using pulse-width modulated signals. When the fuel control system is operating, the ECM controls the fuel quantity control valve using multiple pulse duty ratios. The system adjusts the rail pressure to the standard level calculated by the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0001 Fuel Volume Regulator Control Circuit / Open Open in fuel quantity control valve circuit for 0.1 seconds.
(1 trip detection logic)
·

Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

·

Fuel quantity control valve (fuel supply pump assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0001
·

Target Common Rail Pressure

·

Common Rail Pressure

·

Quantity Regulation Valve - Current Value from Common Rail



WIRING DIAGRAM

A351166E08
0.604,2.073 2.125,2.302 1.521,0.229 10 false EFI MAIN NO. 1 1.323,0.917 1.708,1.198 0.385,0.281 10 false 5 2.083,0.917 2.469,1.198 0.385,0.281 10 false 3 2.083,1.219 2.469,1.5 0.385,0.281 10 false 1 1.323,1.229 1.708,1.51 0.385,0.281 10 false 2 0.615,3.167 1.844,3.365 1.229,0.198 10 false FL MAIN 0.75,3.75 1.979,3.948 1.229,0.198 10 false Battery 6.188,3.844 6.792,4.083 0.604,0.24 10 false ECM 5.771,2.021 6.375,2.26 0.604,0.24 10 false MREL 5.365,2.135 5.969,2.375 0.604,0.24 10 false A62 5.729,1.031 6.333,1.271 0.604,0.24 10 false PCV 5.323,1.031 5.927,1.271 0.604,0.24 10 false B112 5.406,0.844 6.01,1.083 0.604,0.24 10 false 30 5.438,1.948 6.042,2.188 0.604,0.24 10 false 9 3.51,1.333 4.115,1.573 0.604,0.24 10 false B119 3.51,1.49 5.417,1.896 1.906,0.406 10 false Fuel Quantity Control Valve (Fuel Supply Pump Assembly) 2.677,1.188 3.438,1.427 0.76,0.24 10 false EFI NO. 1 3.74,0.927 4.344,1.167 0.604,0.24 10 false 1 4.708,0.927 5.313,1.167 0.604,0.24 10 false 2 3.906,0.927 4.51,1.167 0.604,0.24 10 false +B 4.344,0.927 4.948,1.167 0.604,0.24 10 false PCV 1.219,1.677 2.74,1.906 1.521,0.229 10 false EFI MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT FUEL SUPPLY PUMP ASSEMBLY (FUEL QUANTITY CONTROL VALVE)
a.

Inspect the fuel quantity control valve (fuel supply pump assembly).

Click hereEngine / Hybrid System>2WW FUEL>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - ECM)

NG

8.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL QUANTITY CONTROL VALVE)
2.CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - ECM)
a.

Disconnect the fuel quantity control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B119-2 (PCV) - B112-30 (PCV) Always Below 1 Ω
B119-2 (PCV) or B112-30 (PCV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351159C03
0.177,0.969 0.573,1.219 0.396,0.25 0.896,1.76 1.531,1.208 false 0.135,0.083 0.448,0.24 0.313,0.156 10 false *a 0.219,1.01 0.625,1.208 0.406,0.198 10 false B119 0.729,1.781 1.042,1.938 0.313,0.156 10 false +B
*a Front view of wire harness connector
(to Fuel Quantity Control Valve)


a.

Disconnect the fuel quantity control valve connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B119-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - EFI MAIN NO. 1 RELAY)
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - EFI MAIN NO. 1 RELAY)
a.

Disconnect the fuel quantity control valve connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B119-1 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B119-1 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM POWER SOURCE CIRCUIT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL QUANTITY CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL SUPPLY PUMP>REMOVAL


b.

Perform supply pump learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END