Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0036  HO2S Heater Control Circuit Bank 1 Sensor 2  P0037  HO2S Heater Control Circuit Low Bank 1 Sensor 2  P0038  HO2S Heater Control Circuit High Bank 1 Sensor 2  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0036 HO2S Heater Control Circuit Bank 1 Sensor 2 Open in air fuel ratio sensor (for sensor 2) heater circuit for 2 seconds.
(3 trip detection logic)
·

Open in air fuel ratio sensor (for sensor 2) heater circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored
P0037 HO2S Heater Control Circuit Low Bank 1 Sensor 2 Ground short in air fuel ratio sensor (for sensor 2) heater circuit for 2 seconds.
(3 trip detection logic)
·

Short in air fuel ratio sensor (for sensor 2) heater circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored
P0038 HO2S Heater Control Circuit High Bank 1 Sensor 2 Battery short in air fuel ratio sensor (for sensor 2) heater circuit for 2 seconds.
(3 trip detection logic)
·

Short in air fuel ratio sensor (for sensor 2) heater circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR ((FOR SENSOR 2) (HEATER RESISTANCE))
a.

Inspect the air fuel ratio sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 2)>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)

NG

9.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-1 (AF2+) - B112-130 (AF2+) Always Below 1 Ω
B133-2 (AF2-) - B112-133 (AF2-) Always Below 1 Ω
B133-3 (HAF2) - B112-17 (HAF2) Always Below 1 Ω
B133-5 (TR2) - B112-131 (TR2) Always Below 1 Ω
B133-6 (RE2) - B112-134 (RE2) Always Below 1 Ω
B133-1 (AF2+) or B112-130 (AF2+) - Body ground Always 10 kΩ or higher
B133-2 (AF2-) or B112-133 (AF2-) - Body ground Always 10 kΩ or higher
B133-3 (HAF2) or B112-17 (HAF2) - Body ground Always 10 kΩ or higher
B133-5 (TR2) or B112-131 (TR2) - Body ground Always 10 kΩ or higher
B133-6 (RE2) or B112-134 (RE2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351154C12
0.281,1.083 0.729,1.333 0.448,0.25 1.063,1.844 1.688,1.177 true 0.344,1.125 0.729,1.375 0.385,0.25 10 false B133 0.906,1.875 1.25,2.104 0.344,0.229 10 false +B 0.406,0.281 0.75,0.51 0.344,0.229 10 false *a
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor (for Sensor 2))


a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B133-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - EFI MAIN NO. 1 RELAY)
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - EFI MAIN NO. 1 RELAY)
a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-4 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B133-4 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM POWER SOURCE CIRCUIT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Replace the air fuel ratio sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 2)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED