Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0402  Exhaust Gas Recirculation "A" Flow Excessive Detected  


DESCRIPTION

Refer to DTC P0401.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0401

HINT:

For more information on the EGR control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0402 Exhaust Gas Recirculation "A" Flow Excessive Detected During normal operation, EGR positive deviation exceeds limit value, or EGR rate exceeds limit value for 5 seconds.
(1 trip detection logic)
·

Intake system air leak

·

Air cleaner filter element sub-assembly

·

Diesel throttle body assembly

·

Mass air flow meter sub-assembly

·

EGR valve assembly

·

Turbocharger sub-assembly

·

Swirl Control Valve

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the mass air flow meter sub-assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the swirl control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK INTAKE SYSTEM
a.

Check for air leaks in the intake system from the mass air flow meter sub-assembly to the turbocharger sub-assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

16.REPAIR OR REPLACE INTAKE SYSTEM
2.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Inspect the air cleaner filter element sub-assembly.

OK:

No blockage in air cleaner filter element sub-assembly.



Result:
Proceed to
OK
NG



OK

3.CHECK MASS AIR FLOW METER SUB-ASSEMBLY

NG

15.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
3.CHECK MASS AIR FLOW METER SUB-ASSEMBLY
a.

Check for DTCs related to the mass air flow meter sub-assembly.

OK:

DTCs related to the mass air flow meter sub-assembly are not output.



Result:
Proceed to
OK
NG



OK

4.CHECK SWIRL CONTROL VALVE

NG

14.REPAIR OR REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
4.CHECK SWIRL CONTROL VALVE
a.

Check that the swirl control valve is not stuck closed or blocked.

OK:

Swirl control valve is moving correctly and not stuck closed or blocked.



Result:
Proceed to
OK
NG



OK

5.CHECK DIESEL THROTTLE BODY ASSEMBLY

NG

13.REPLACE SWIRL CONTROL VALVE
5.CHECK DIESEL THROTTLE BODY ASSEMBLY
a.

Check for DTCs related to the diesel throttle body assembly.

OK:

DTCs related to the diesel throttle body assembly are not output.



Result:
Proceed to
OK
NG



OK

6.CHECK EGR VALVE ASSEMBLY

NG

12.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
6.CHECK EGR VALVE ASSEMBLY
a.

Check for DTCs related to the EGR valve assembly.

OK:

DTCs related to the EGR valve assembly are not output.



Result:
Proceed to
OK
NG



OK

7.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

11.REPAIR OR REPLACE EGR VALVE ASSEMBLY
7.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check for DTCs related to the turbocharger sub-assembly.

OK:

DTCs related to the turbocharger sub-assembly are not output.



Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0402)

NG

10.REPAIR OR REPLACE TURBOCHARGER SUB-ASSEMBLY
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0402)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0402 B




A

END

B

9.REPLACE ECM
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Repair or replace turbocharger sub-assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE EGR VALVE ASSEMBLY
a.

Repair or replace EGR valve assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Repair or replace diesel throttle body assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE SWIRL CONTROL VALVE
a.

Replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Perform the swirl valve learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Repair or replace mass air flow meter sub-assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner element assembly.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning parts of the intake system.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END