Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0403  Exhaust Gas Recirculation "A" Control Circuit  P0404  Exhaust Gas Recirculation "A" Control Circuit Range / Performance  P0489  Exhaust Gas Recirculation "A" Control Circuit Low  P0490  Exhaust Gas Recirculation "A" Control Circuit High  


DESCRIPTION

Refer to DTC P0401.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0401

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0403 Exhaust Gas Recirculation "A" Control Circuit Open or short in EGR valve circuit for 0.22 seconds.
(3 trip detection logic)
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored
P0404 Exhaust Gas Recirculation "A" Control Circuit Range / Performance Either condition is met (3 trip detection logic):
·

EGR valve circuit overcurrent for 0.22 seconds.

·

EGR valve sensor circuit over temperature for 0.22 seconds.

·

Battery short in EGR valve circuit for 0.22 seconds.


·

Open or short in EGR valve circuit

·

EGR valve assembly

·

Cooling fan system

·

ECM


Comes on DTC stored
P0489 Exhaust Gas Recirculation "A" Control Circuit Low Ground short in EGR valve circuit for 0.22 seconds.
(3 trip detection logic)
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored
P0490 Exhaust Gas Recirculation "A" Control Circuit High Battery short in EGR valve circuit for 0.22 seconds.
(3 trip detection logic)
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored

Related Data Lis
DTC No. Data List
P0403
P0404
P0489
P0490
·

Actual EGR Valve Pos

·

Target EGR Valve Pos



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



PROCEDURE

1.INSPECT EGR VALVE ASSEMBLY
a.

Inspect the EGR valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

5.REPLACE EGR VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B131-2 (M+) - B112-48 (EGM+) Always Below 1 Ω
B131-1 (M-) - B112-18 (EGM-) Always Below 1 Ω
B131-2 (M+) or B112-48 (EGM+) - Body ground Always 10 kΩ or higher
B131-1 (M-) or B112-18 (EGM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Perform the EGR learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END