Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1443  Particulate Filter Lamp Overload Inhibit Regeneration  


DESCRIPTION

HINT:

For more information on the diesel particulate filter (DPF) catalyst regeneration control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1443 Particulate Filter Lamp Overload Inhibit Regeneration Differential pressure exceeding threshold detected for 10 seconds or more.
(3 trip detection logic)
NOTICE:

If the amount of soot is too large, the DPF catalytic converter may overheat during operation.

Therefore, this DTC stops operation of the DPF catalytic converter when the amount of soot exceeds a predetermined amount.


·

Driven short distance

·

Oil level

·

Swirl control valve

·

Differential pressure sensor

·

Exhaust manifold converter sub-assembly (DPF catalytic converter)

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1443
·

Filtered Pressure Value at Particle Filter Upstream

·

Adaptation Value of Differential Pressure at Particle Filter



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the DPF catalyst, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the differential pressure sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the swirl control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning V alues Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE OIL LEVEL AND REPLACEMENT INTERVAL
a.

Check the engine oil level and replacement interval, and then adjust the oil level or replace oil as necessary.


Result:
Proceed to
NEXT



NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)
2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Swirl Flap
Data List Display
Swirl Valve Actuator Position
50004 371 7 198
OK:

The value of "Swirl Valve Actuator Position" changes according to the amount "Actuator Test of Swirl Flap" is operated, and the swirl flap operates smoothly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF FAN HIGH SPEED)

NG

10.REPAIR OR REPLACE SWIRL CONTROL VALVE
3.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF FAN HIGH SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan High Speed
50004 371 10

d.

Check that the cooling fan operates.

OK:

The cooling fan operates normally



Result:
Proceed to
OK
NG



OK

4.CHECK DIFFERENTIAL PRESSURE SENSOR

NG

4.CHECK DIFFERENTIAL PRESSURE SENSOR
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Filtered Pressure Value at Particle Filter Upstream.

Powertrain > Engine and ECT > Data List
Tester Display
Filtered Pressure Value at Particle Filter Upstream
50003 371 117

d.

Read the value.

OK:

Difference between Data List item "Filtered Pressure Value at Particle Filter Upstream" and Data List items "Atmosphere Pressure" and "MAP" is within 8 kPa.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (ADAPTATION VALUE OF DIFFERENTIAL PRESSURE AT PARTICLE FILTER)

NG

9.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.READ VALUE USING GTS (ADAPTATION VALUE OF DIFFERENTIAL PRESSURE AT PARTICLE FILTER)
NOTICE:

The EGR valve is closed during the test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Adaptation Value of Differential Pressure at Particle Filter.

Powertrain > Engine and ECT > Data List
Tester Display
Adaptation Value of Differential Pressure at Particle Filter
50003 371 116

d.

Start the engine and warm it up until the engine coolant temperature is 80°C (176°F) or higher.


e.

Test 1

i.

Idle the engine for 2 seconds.


ii.

Read the value for 10 seconds.

OK:

With the ignition switch ON, "Adaptation Value of Differential Pressure at Particle Filter" value is within 3.5 kPa.




f.

Test 2

i.

Maintain the engine speed at 2000 rpm for 2 seconds.


ii.

Maintain the engine speed at 2000 rpm and read the value for 10 seconds.

OK:

With the ignition switch ON, "Adaptation Value of Differential Pressure at Particle Filter" value is within 7.5 kPa.




g.

Test 3

i.

With the engine running without load at approximately 3800 rpm, wait for 2 seconds.


ii.

With the engine running without load at approximately 3800 rpm, read the value for 10 seconds.

OK:

With the ignition switch ON, "Adaptation Value of Differential Pressure at Particle Filter" value is within 20 kPa.




Result:
Proceed to
OK
NG



OK

6.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)

NG

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
6.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Check DPF catalytic converter for damage.

i.

Check downstream of the DPF catalytic converter and inside the exhaust tailpipe for soot deposits.

OK:

No soot deposits.




Result:
Proceed to
OK
NG



OK

7.DPF REGENERATION PROCEDURE

NG

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
7.DPF REGENERATION PROCEDURE
NOTICE:

Check the following items before beginning the DPF regeneration procedure. If there is a malfunction with any of the following items, it may not be possible to perform DPF rejuvenation normally.

·

Engine oil level normal

·

10 L of fuel or more remaining

·

No malfunction in intake system



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / DPF Rejuvenation Timing Reset.

Powertrain > Engine and ECT > Utility
Tester Display
DPF Rejuvenation Timing Reset
50005 371 4372

d.

Driving test.

i.

Start the engine and warm it up until the engine coolant temperature is 80°C (176°F) or higher.


ii.

Turn all electrical loads on (air conditioner, seat heater, etc.).


iii.

Drive the vehicle at an average vehicle speed of 90 km/h (56 mph) or more for 2 hours or more.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Distance Since Last Succeeded Regeneration.

Powertrain > Engine and ECT > Data List
Tester Display
Distance Since Last Succeeded Regeneration
50003 371 126

f.

After DPF regeneration completes, check that "Distance Since Last Succeeded Regeneration" is 0 km.


NOTICE:

If the DPF regeneration procedure cannot complete, perform step 8 (REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)).


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Replace the exhaust manifold converter sub-assembly (DPF catalytic converter).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>MONOLITHIC CONVERTER>REMOVAL


b.

Perform the DPF history information reset and NOx storage catalyst learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


b.

Perform the differential pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE SWIRL CONTROL VALVE
a.

Repair or replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL

HINT:

When the swirl control valve is replaced, perform initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END