Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1450  Fault Path for EGR Valve Long Time Drift  


DESCRIPTION

Refer to DTC P0401.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0401

HINT:

For more information on the EGR control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1450 Fault Path for EGR Valve Long Time Drift When difference between first EGR valve learning value and current learning value exceeds threshold.
(3 trip detection logic)
EGR valve position sensor (EGR valve assembly) Does not come on DTC stored

Related Data List
DTC No. Data List
P1450
·

First Learnt Offset-Value of EGR Valve

·

Last Learnt Offset-Value of EGR Valve



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning V alues Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (FIRST LEARNT OFFSET-VALUE OF EGR VALVE AND LAST LEARNT OFFSET-VALUE OF EGR VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / First Learnt Offset-Value of EGR Valve and Last Learnt Offset-Value of EGR Valve.

Powertrain > Engine and ECT > Data List
Tester Display
First Learnt Offset-Value of EGR Valve
Last Learnt Offset-Value of EGR Valve
50003 371 95,96

d.

Read the value.

OK:

Deviation value should be less than 10%.


HINT:

EGR value is operated correctly if there is no difference among the above values.



Result:
Proceed to
OK
NG



OK

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P1450)

NG

3.REPLACE EGR VALVE ASSEMBLY
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P1450)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P1450 B




A

END

B

3.REPLACE EGR VALVE ASSEMBLY
3.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Perform EGR learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END