Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2002  Diesel Particulate Filter Efficiency Below Threshold Bank 1  


DESCRIPTION

HINT:

For more information on the diesel particulate filter (DPF) catalyst regeneration control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2002 Diesel Particulate Filter Efficiency Below Threshold Bank 1 The fault is detected when the quotient of the integrated differential pressure and the integrated threshold value falls below a limit value.
(3 trip detection logic)
·

Differential pressure sensor

·

Open or short in differential pressure sensor circuit

·

Exhaust manifold converter sub-assembly (DPF catalytic converter)

·

Air hose

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2002 Adaptation Value of Differential Pressure at Particle Filter

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the DPF catalyst, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the differential pressure sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B127-1 (VC) - B112-70 (VCPX) Always Below 1 Ω
B127-2 (PEX) - B112-85 (PEX) Always Below 1 Ω
B127-3 (E2) - B112-71 (EPEX) Always Below 1 Ω
B127-1 (VC) or B112-70 (VCPX) - Body ground Always 10 kΩ or higher
B127-2 (PEX) or B112-85 (PEX) - Body ground Always 10 kΩ or higher
B127-3 (E2) or B112-71 (EPEX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351158C26
0.302,1.146 0.75,1.365 0.448,0.219 0.948,1.792 1.354,1.281 true 2.438,1.792 2.083,1.281 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.375,1.167 0.844,1.365 0.469,0.198 10 false B127 0.844,1.813 1.313,2.01 0.469,0.198 10 false VC 2.396,1.813 2.865,2.01 0.469,0.198 10 false E2
*a Front view of wire harness connector
(to Differential Pressure Sensor)


a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B127-1 (VC) - B127-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION

NG

9.REPLACE ECM
3.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION
a.

Check hose pipes between exhaust system and differential pressure sensor. (for correct installation, arrangement (kinks), permeability (coking possible) and cracks).

OK:

Part is securely installed.



Result:
Proceed to
OK
NG



OK

4.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)

NG

8.CONNECT AIR HOSE
4.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Check that the DPF catalytic converter is installed.

OK:

DPF catalytic converter is installed.


HINT:

If the DPF catalytic converter is not installed, the exhaust tailpipe turns black from soot.



b.

Check that the DPF catalytic converter is not damaged.

OK:

DPF catalytic converter is not damaged.


HINT:

If the DPF catalytic converter is not installed, the exhaust tailpipe turns black from soot.

·

If the DPF catalytic converter is damaged, the exhaust tailpipe and edge of the filter turn black from soot.

·

Disconnect the front exhaust pipe assembly from the exhaust manifold converter sub-assembly (DPF catalytic converter) and check for soot stuck inside the exhaust manifold converter sub-assembly (DPF catalytic converter).




Result:
Proceed to
OK
NG



OK

5.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

7.INSTALL OR REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
5.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


b.

Perform the differential pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2002)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2002)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P2002 B




A

END

B

9.REPLACE ECM
7.INSTALL OR REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Install or replace the exhaust manifold converter sub-assembly (DPF catalytic converter).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>MONOLITHIC CONVERTER>REMOVAL


b.

Perform DPF history information reset and NOx storage catalyst learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONNECT AIR HOSE
a.

Install the air hose.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END