Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P245B  Exhaust Gas Recirculation Cooler Bypass Control Circuit Range / Performance Bank 1  


DESCRIPTION

Refer to DTC P245A.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P245A

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245B Exhaust Gas Recirculation Cooler Bypass Control Circuit Range / Performance Bank 1 EGR cooler bypass switching valve assembly circuit over temperature for 0.05 seconds.
(3 trip detection logic)
·

EGR cooler bypass switching valve assembly

·

Open or short in EGR cooler bypass switching valve assembly circuit

·

Cooling fan system

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF FAN HIGH SPEED AND LOW SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed and Actuator Test of Fan Low Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan High Speed
50004 371 10
Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan Low Speed
50004 371 11
OK:

Cooling fan operates according to operation.



Result:
Proceed to
OK
NG



OK

2.INSPECT EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY

NG

11.REPAIR OR REPLACE COOLING FAN SYSTEM
2.INSPECT EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Inspect the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - ECM)

NG

10.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR cooler bypass switching valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B109-2 (ECBV) - B112-16 (ECBV) Always Below 1 Ω
B109-2 (ECBV) or B112-16 (ECBV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351155C04
0.333,1.083 0.729,1.292 0.396,0.208 2.5,1.76 1.885,1.292 false 0.156,0.188 0.469,0.344 0.313,0.156 10 false *a 0.375,1.104 0.823,1.365 0.448,0.26 10 false B109 2.563,1.74 3.01,2 0.448,0.26 10 false +B
*a Front view of wire harness connector
(to EGR Cooler Bypass Switching Valve Assembly)


a.

Disconnect the EGR cooler bypass switching valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B109-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

7.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the EGR cooler bypass switching valve assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B109-1 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B109-1 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK ECM POWER SOURCE CIRCUIT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Replace the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE COOLING FAN SYSTEM
a.

Repair or replace the cooling fan system.

Click hereEngine / Hybrid System>2WW COOLING>COOLING FAN SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED