Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P3148  Cylinder 1 High Pressure Injector High Side Circuit Shorted to Coil  P3151  Cylinder 2 High Pressure Injector High Side Circuit Shorted to Coil  P3154  Cylinder 3 High Pressure Injector High Side Circuit Shorted to Coil  P3157  Cylinder 4 High Pressure Injector High Side Circuit Shorted to Coil  


DESCRIPTION

The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.

HINT:
·

Injector driver is built into the ECM.

·

For more information on the injector assembly and fuel injection control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P3148 Cylinder 1 High Pressure Injector High Side Circuit Shorted to Coil Short circuit between high-side and low-side of the power stage (cylinder No. 1).
(1 trip detection logic)
·

Open or short in No. 1 injector assembly circuit

·

No. 1 injector assembly

·

ECM


Comes on DTC stored
P3151 Cylinder 2 High Pressure Injector High Side Circuit Shorted to Coil Short circuit between high-side and low-side of the power stage (cylinder No. 2).
(1 trip detection logic)
·

Open or short in No. 2 injector assembly circuit

·

No. 2 injector assembly

·

ECM


Comes on DTC stored
P3154 Cylinder 3 High Pressure Injector High Side Circuit Shorted to Coil Short circuit between high-side and low-side of the power stage (cylinder No. 3).
(1 trip detection logic)
·

Open or short in No. 3 injector assembly circuit

·

No. 3 injector assembly

·

ECM


Comes on DTC stored
P3157 Cylinder 4 High Pressure Injector High Side Circuit Shorted to Coil Short circuit between high-side and low-side of the power stage (cylinder No. 4).
(1 trip detection logic)
·

Open or short in No. 4 injector assembly circuit

·

No. 4 injector assembly

·

ECM


Comes on DTC stored

HINT:
·

If DTC P3148, P3151, P3154 and/or P3157 is stored, the following symptoms may appear:

·

Engine stall




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM and/or injector assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT INJECTOR ASSEMBLY
a.

Inspect the injector assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

5.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Disconnect the injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-2 (#10) - B112-29 (IJ1+) Always Below 1 Ω
I1-1 (#1) - B112-59 (IJ1-) Always Below 1 Ω
I2-2 (#20) - B112-28 (IJ2+) Always Below 1 Ω
I2-1 (#2) - B112-58 (IJ2-) Always Below 1 Ω
I3-2 (#30) - B112-27 (IJ3+) Always Below 1 Ω
I3-1 (#3) - B112-57 (IJ3-) Always Below 1 Ω
I4-2 (#40) - B112-26 (IJ4+) Always Below 1 Ω
I4-1 (#4) - B112-56 (IJ4-) Always Below 1 Ω
I1-2 (#10) or B112-29 (IJ1+) - Body ground Always 10 kΩ or higher
I1-1 (#1) or B112-59 (IJ1-) - Body ground Always 10 kΩ or higher
I2-2 (#20) or B112-28 (IJ2+) - Body ground Always 10 kΩ or higher
I2-1 (#2) or B112-58 (IJ2-) - Body ground Always 10 kΩ or higher
I3-2 (#30) or B112-27 (IJ3+) - Body ground Always 10 kΩ or higher
I3-1 (#3) or B112-57 (IJ3-) - Body ground Always 10 kΩ or higher
I4-2 (#40) or B112-26 (IJ4+) - Body ground Always 10 kΩ or higher
I4-1 (#4) or B112-56 (IJ4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of malfunctioning cylinder.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>REMOVAL


b.

Register the injector assembly compensation code.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END